Utax XC 9148 Handbuch

instruction handbook

wide format copy-/plotsystem

XC 9148

(1)

Thank you for purchasing the Multi-Function Printer XC 9148.

This Hardware Operation Guide contains functional and operational explanations for the XC 9148.

Please read this Hardware Operation Guide carefully before using the printer.

Please keep this Hardware Operation Guide for future reference.

1. When this product is installed in North America.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) this device must

accept any interference received, including interference that may cause undesired operation.

2. When this product is installed in Europe

This equipment complies with the requirements in Pub.22 of CISPR Rules for a Class B

computing device.

Operation of this equipment in a residential area may cause unacceptable interference to radio

and TV reception requiring the operator to take whatever steps are necessary to correct the

interference.

Do not install Machine around other electronic equipment or other precision instruments.

Other devices may be effected by electrical noise during operation.

If the Machine is installed near other electronic equipment, such as a TV or a radio,

interference to said equipment, such as noise or flickering, may occur.

Use a separate power line and install the PRINTER as far as possible from said equipment.

The International ENERGY STAR ® Office Equipment Program is an international program that

promotes energy saving through the penetration of energy efficient computers and other office

equipment. The program backs the development and dissemination of products with functions that

effectively reduce energy consumption. It is an open system in which business proprietors can

participate voluntarily. The targeted products are office equipment such as computers, monitors,

printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and logos are

uniform among participating nations.

The symbol shown indicates that this product conforms to Directive

2002/96/EC of the European Parliament and the council of 27 January

2003 on waste electrical and electronic equipment (WEEE) and does not

apply to countries outside of EU.

As an ENERGY STAR ® Partner, Katsuragawa Electric Co., Ltd. has determined

that this product meets the ENERGY STAR ® guidelines for energy efficiency.

The symbol shown indicates that this product conforms to

SJ/T11364-2006 of People’s Republic of China Electronic

Industry Standard and does not apply to countries outside of

People’s Republic of China.

The symbol shown indicates that this product conforms to GB

18455-2001 11364-2006 of National Standard of the People’s

Republic of China and does not apply to countries outside of

People’s Republic of China.

(2)

Safety Warnings

The following warnings are very important in order to safely use this product.

These notes are important in preventing danger to the operator or operation of the printer.

The following symbols are found throughout the USER’S Manual and have the following meaning:

WARNING

This WARNING mark means that there is a possibility of death or serious

injury if you ignore or do not follow the said instruction.

CAUTION

This CAUTION mark means that there is a possibility of injury or physical

damage if you ignore or do not follow the said instruction.

When marked with this symbol, “DO NOT ATTEMPT”

When marked with this symbol, “pay close attention to”

(3)

WARNING

1. The Power source should be as follows:

In U.S.A. : 120V plus/minus10%, 50/60Hz, 15A or higher

In Europe : 220-240V plus6% or minus10%, 50/60Hz, 10A or higher

2. Use a circuit with a dedicated breaker.

3. Install the product as close to the wall outlet as possible.

4. If you wish to move the printer, please contact your service personnel.

Ground the product with a correct ground source or you may be electrically

shocked.

1. Do not plug in the printer into a multi-wire connector in which some other

equipment is plugged into.

It may cause a fire due to outlet overheating.

2. Do not damage the Power Cord by stepping on or placing heavy items

on it.

If the Power Cord is damaged, it may cause a fire or you may receive

an electric shock. REPLACE THE CORD IF DAMAGED!

1. Do not put a flower vase, a flowerpot or any water-filled item on the

product.

Spilt water could cause a fire or an electric shock.

2. If the product generates an abnormal smell or noise, turn it off and

unplug it from the wall electrical outlet immediately.

1. Do not remove the screw and do not open the cover if not instructed to

do so in this User’s Manual. If you ignore this warning, you may be burnt

or receive an electric shock due to a hot item or electrically charged part

inside of the printer.

2. Do not disassemble or tamper with the printer.

It may result in a fire or an electrical shock.

Do not throw the toner into a fire or other sources of heat, as it can

explode.

(4)

CAUTION

There are hot items inside of the printer.

Take great care not to touch these items when you remove mis-fed media.

Do not pull the cord when you unplug the printer as you may damage the

Power Cord.

Do not install the printer in a humidified room or a dusty room.

Also, do not install the printer on an unstable floor as injuries may occur.

1. Unplug the printer before you move it.

The power cord may be damaged and it may result in a fire or electric

shock.

2. If you do not use the printer for a long duration (holidays, company

shutdown) turn off and unplug the printer from the outlet for safety.

Ventilate the room well if you print in a small area.

(5)

POWER CORD INSTRUCTION

The installation of (or exchange to) a power plug which fits in the wall outlet of the

installation location shall be conducted in accordance with the following:

WARNING

Select a power plug which meets the following criteria;

- The plug has a voltage and current rating appropriate for the product’s rating

marked on its name plate.

- The plug meets regulatory requirements for the area.

- The plug is provided with a grounding pin or terminal.

If the appropriate plug does not fit the wall outlet in the installation, the customer shall

install an appropriate outlet.

Connector Type:

Configuration Standard Rating Usually found in

IEC60320:C13 10A 250V (IEC)

15A 125V (UL)

Plug Type: Model Rating 220-240V

Configuration Standard Rating Usually found in

CEE7/7 10A 250V European countries

KS C 8305 10A 250V Korea

AS/NZS 3112 10A 250V Australia

New Zealand

GB1002

GB2099.1

10A 250V China

IRAM 2073 10A 250V Argentina

BS 1363 10A 250V United Kingdom

SASO 2203 10A 250V Saudi Arabia

BS 546A

IS-1293

SABS-1293

15A 250V United Kingdom

India

South Africa

SEV 1011 10A 250V Switzerland

Chapter 1 Before Use1-1

Chapter 1

Before Use

page

1. 1 Installation Requirements 1-2

1. 2 Originals Prohibited from Duplication 1-3

1. 3 Features 1-4

1. 4 Specifications 1-5

1. 4. 1 General 1- 5

1. 4. 2 Printer part 1- 6

1. 4. 3 Scanner part 1- 8

1. 5 Appearance 1-9

1. 5. 1 Front view 1- 9

1. 5. 2 Rear view 1-10

1. 6 Specifications for the Scan Original 1-11

1. 7 Specifications for the Printing Paper 1-14

1. 7. 1 Papers not available to use 1-14

1. 7. 2 Keeping the paper in the custody 1-15

1. 7. 3 Treatment against environmental condition 1-16

Chapter 1 Before Use1-2

1. 1 Installation Requirements

The following conditions are required for installation of the equipment.

1. POWER SOURCE should be rated as follows.

In U.S.A. : 120V plus/minus 10%, 50/60Hz, 15A or higher

In Europe : 2V plus 6% or minus10%, 50/60Hz, 10A or higher

2. The equipment must be on an exclusive circuit.

3. The outlet must be near the equipment and easily accessible.

1. Make sure to connect this equipment to a grounded outlet.

2. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near

the equipment and shall be easily accessible.

The site temperature range = 10 to 32 degrees Centigrade, with the humidity between

15% to 85% RH. (NON CONDENSING)

Keep the printer away from water sources, boilers, humidifiers or refrigerators.

1. The installation site must not have open flames, dust or ammonia gases.

2. The equipment must not be exposed to the air vents from air conditioners.

It may affect the image quality.

3. The equipment should not be exposed to the direct sunlight.

Please draw curtains to block any sunlight.

When you open the Movable Unit, do not expose the Photoconductive Drum

to strong (intense) light as this will damage the Drum.

Ozone will be generated while this equipment is use, although the quantity generated

is within safe levels. (see certifications)

Ventilate the room, if required.

Keep ample room around the equipment to ensure comfortable operation.

(Refer to the following figure.)

The equipment must be leveled and the floor strength must be ample to sustain the

weight of the equipment.

Device

(Front)

(Rear)

30cm/12” or larger

80cm/32” or larger

90cm/35.4” or larger

for Paper Tray (option)

* L + R = 35cm/14” or larger

(R must be larger than L)

(L = 5cm/2” or larger

recommended)

Chapter 1 Before Use1-3

1. 2 Originals Prohibited from Duplication

It is not necessarily allowed to copy every kind of original.

You may be punished by the law if only you possess the copy of some kind of original.

We recommend you to consider enough before you copy such original.

[Originals prohibited from copying by the law]

1. It is not allowed to copy Currency (Bill, Money, Bank Note, etc.), Government issued

Negotiable Instruments (National Bonds, Security, Local Debt Bonds, etc.).

2. It is not allowed to copy Foreign Currency or Foreign Negotiable Instruments.

3. It is not allowed to copy unused postal stamps or government postcards without permission

to make replica from Government.

4. It is not allowed to copy Government issued revenue stamps, certificate stamps which are

prescribed by Liquor Tax Act or the Commodity Tax Act.

[Special items to be cared]

1. It is warned by the government to copy private issued securities (stock certificate, draft,

check, goods ticket, etc.), commutation ticket or book of tickets, excluding that some specific

company copies such originals as many as it requires for its own business.

2. We recommend you not to copy freely such originals as government issued passport, public

or private issued licenses, automobile inspection certification, IDs and tickets like pass or

meal.

Reference Law Prohibited items to copy

Regulations to control fake currency and

Bond.

Currency (Bill, Money, Bank Note, etc.),

Government issued Negotiable Instruments

(National Bonds, Security, Local Debt Bonds,

etc.)

Control Law against Forged & faked

Foreign Currency, Bill, Bank Note and Bond

Foreign Currency or Foreign Negotiable

Instruments

Forged postal stamps control law Unused postal stamps or government postcards

Forged revenue stamps control law Government issued revenue stamps, and

certificate stamps prescribed by Liquor Tax Act

or Commodity Tax Act

Currency similarity securities Control Law Private issued securities (stock, draft, check,

goods ticket, etc.), commutation or book tickets

[Originals protected by the copyright]

It is prohibited to copy such originals as book, music, paintings, printed copy, maps, drawings,

movie and pictures which are protected by the copyright, except for personnel or family use or

similar purpose.

Chapter 1 Before Use1-4

1. 3 Features

(1) The XC 9148 is a single footprint Multi-Function Printer which can copy, scan and print.

Advanced drivers and comprehensive print utilities make the XC 9148 an advanced,

easy to use system. (some functions may be optional)

(2) KIP HDP technology generates no waste toner.

(3) The combination of the KIP HDP Plus imaging system with mono-component minute toner

produces high definition lines, distinctive greyscale and consistent blacks.

(4) The maximum paper width is 36” (914mm) wide, and the minimum is 11” (279mm). The

maximum paper length is 6m (with 36” paper) or, and the minimum is 8.5” (210mm).

(5) Up to 600dpi print resolutions with an enhanced scanning system produces the highest quality

images controlled by an advanced KIP Image Process System.

(6) Easy access to USB port allows users to provide efficient productivity by using “File to Print” /

“Scan to USB” (option).

(7) 2-way print ejection (top / rear) suits the preference of the user’s print handling.

(8) Various media source; roll media feeding (2 rolls), cut sheet manual feeding, Paper Tray

multiple cut sheet feeder (option)

(9) Contactless IC card reader for more efficient accounting management (option)

(10) User-friendly touch screen control panel with tilt / swivel

Inhaltsverzeichnis

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung