UTEK ULTRALOQ Bedienungsanleitung
ULTRALOQBoltFingerprint
Installation and User Guide
( )
V2.0
• Do not use a power drill for installation.
• Install and test the lock with the door open to avoid being
locked out.
• Please read all the instructions before contacting customer
support.
• Please contact customer support before returning the
product to the store.
• Do not install the batteries before installing the lock!
• Follow the instructions in sequential order!
• This lock is designed for the following operating temperatures:
Outside: -4°F(-20°C)to149°F(65°C)
Inside: 14 °F (-10 °C) to 131 °F (55 °C)
• Suggest to use AA Alkaline Battery, or manufacture suggested
Lithium Battery. Don’t use Rechargeable Battery.
To ensure the best service, please register your account at
www.u-tec.com/register.html
Need Help?
For technical documents and more
Please visit support.u-tec.com
Important Notes
Statements
- 1 -
Before using all ULTRALOQ products, please read all
applicable terms, rules, policies and usage provisions found at
www.u-tec.com/company/privacy. By using your
ULTRALOQ, you agree to be bound by the U-tec Privacy Policy.
ULTRALOQ Terms & Policies
Note:The Exterior Assembly of ULTRALOQ Bolt
Fingerprint is waterproof, but the Interior Assembly is not
waterproof at all due to the battery box.
ENGLISH
- 2 -
Packing List
Screw AStrike Bolt
Screw FScrew E AA Alkaline Batteries
May not be included
for some regions
Interior
Assembly
Exterior
Assembly
Interior Assembly
Mounting Plate
Screw C Screw DScrew B
User Guide Drill Template Reset Needle
DrillTemplate
(V1.6)
Faceof the door Edgeofthe door
Centerline
Backset
2
3
/
4
”
(70mm)
2
3
/
8
”
(60mm)
1
3
/
4
”
(44mm)
1
3
/
8
”
(35mm)
Centerline
Backset
2
3
/
4
”
(70mm)
2
3
/
8
”
(60mm)
1
3
/
4
”
(44mm)
1
3
/
8
”
(35mm)
Fold
(V1.6)
Plantillade Perforación
Carade la puerta Bordedelapuerta
Eje
Carade la puertaBordede la puerta
Eje
Doblar
Entradade
lacerradura
Entradade
lacerradura
Fold
Doblar
DrillTemplate
(V1.6)
(V1.5)
Plantillade Perforación
Faceof the doorEdge of the door
2”(50mm)
2”
(50mm)
Backup KeyDoor Sensor
Installation Guide
Installation Video
- 3 -
1. Preparing Door
Check the door’s dimensions.
Step 1
Measure to confirm that the door is between
13
/
8”
~
13
/
4”
(35 mm-45 mm) thick.
If your door is thicker than
13
/
4”
, please visit support.u-tec.com
to get help.
Step 2
Measure to confirm that the diameter of the hole is
21
/
8 ”
(53
mm) or
11
/
2 ”
(38 mm)
Step 3
Measure to confirm that the backset is either
23
/
8 ” or 23
/
4
”
(60 mm or 70 mm).
Step 4
Measure to confirm that the diameter of the hole in the door
edge is
1”
(25 mm).
Step 5
Measure to confirm the depth of the hole in the frame is at least
1''(25 mm).
If you have a new door, please drill the holes according to Drill
Template.
Please scan this QR code to watch the easy
step by step installation video before
attempting to install ULTRALOQ.
Or you can also view the webiste directly.
www.u-tec.com/lock/Bolt_F_WiFi/guide
1”
25 mm
53 mm
(35 mm ~ 45 mm)
13
/
8”
~
13
/
4”
2
3
/
4 ”
2
3
/
8 ”
(70 mm)
OR
(60 mm)
38mm
1
1
/
2
”
1''(25 mm)
21
/
8 ”
- 4 -
2. Installing Bolt and Strike
Note: Bolt is set for 2
3
/
8
” backset initially. It can be
adjusted to 2
3
/
4
” if needed.
To adjust it please make sure the bolt is retracted,
then, press it, twist and pull it or push it to your desired
length.
Step 2
Install Strike into the door frame.
Step 1
Install Bolt into the door. Make sure the UP icon goes up.
23
/ 8 ”
2 3
/
4
”
(60 mm)
(70 mm)
Adjust the Bolt
basket length
Screw A
Screw C
Screw B
ENGLISH
- 5 -
Step 1
Keep Bolt retracted and the cylinder tailpiece horizontal.
Install ExteriorAssembly. Please do not insert the
mechanical key during installation .
Step 2
Align its two sticks with two holes on Bolt. The cable goes
through the hole below Bolt.
If your door has a
11
/
2 ”
(38 mm) bore hole, remove the
spacer as shown.
3. Installing Exterior Assembly
- 6 -
Step 1
Route the cable through the hole on Interior Assembly
Mounting Plate.
Step 2
Secure Interior Assembly Mounting Plate to Exterior
Assembly using Screws D.
4. Installing Interior Assembly Mounting Plate
Screw D
ENGLISH
Pull Up
- 7 -
5. Installing Interior Assembly
Step 1
Remove the battery cover of the Interior Assembly.
Step 2
Insert the connector of the cable to the socket on Interior
Assembly. When you plug the connector, please make sure the
black teeth faces up. Press the connector in firmly until it is
completed seated.
Step 3
Rotate the knob and keep it in a vertical position to stay
unlocked.
Step 4
Attach Interior Assembly to Mounting Plate and tighten 2
Screws E.
Warning: Please do not install the batteries before installing interior assembly,
otherwise the keypad may not be powered on.
Screw E
Unlocked
The door sensor lets you know whether the door is open or
closed through the App. When the auto lock is enabled in the
App, your ULTRALOQ will only lock it self when the door is
closed.
Please do not mount the door sensor on the keypad side.
Please do not mount the door sensor on the kind of metal
door that interferes with the magnet inside the door sensor
(In this case, the door sensor sticks to the metal door
magnetically).
The door sensor can be installed on the wooden door or the
kind of metal door that will not interfere with the door sensor
(In this case, the door sensor will not stick to the door
magnetically).
- 8 -
7. Installing the Door Sensor(Optional)
6. Installing the Batteries and Performing the
Door Handing Process
This step will teach your lock the orientation of your door and is
crucial to lock operation.
Step 1
Rotate the turn and keep it in a vertical position to stay
unlocked.
Step 2
Insert 8 AA Alkaline Batteries and keep the batteries on the
battery pull tab. Then install the battery cover.
Note：Any Fingerprint or pressing any digit button for 4 times can unlock
ULTRALOQ Bolt Fingerprint in Factory Default Mode.
Step 3
Direction calibration: Please keep Bolt
unlocked and press and hold the
number 5 until you hear two short
beeps, then the lock will rotate to start
the direction self-calibration.
To avoid deadbolt jamming, please note
that this step should be done after the
lock is installed on the door.
ENGLISH
Note: Please refer to the guide in U-tec App for more information.
Door
Frame
Option 1 Installing with Sticker
Peel o either side of the sticker and push it against the door
frame about 10s. Peel o the other side and secure the door
sensor on the sticker firmly. Put on the door sensor cover at last.
Option 2 Installing with Screw F
Push the door sensor against the wall and secure it with Screw
F. You may need to drill a hole first if the door frame is hard to
screw in with Screw F directly. Put on the door sensor cover at
last.
UP
Door
Frame
UP
Door
Frame
Note:Door sensor should be
mounted as close to the edge
of your door frame as possible,
or within 0 to 1''(25 mm) from
the edge, and as close to the
bottom of the extended
deadbolt as possible, or within
0 to 1''(25 mm) from the edge.
- 9 -
Door
Frame
Inhaltsverzeichnis
Sprachen:
