Utilitech DUSK-TO-DAWN AHR100-00 Bedienungsanleitung

Questions, problems, missing parts? Before returning to your retailer, call our customer

service department at 1-866-994-4148, 8 a.m. - 6 p.m., EST, Monday - Thursday,

ITEM #0319896

MODEL #AHR100-00

DUSK-TO-DAWN

LIGHT

Français p. 13

Español p. 25

8 a.m. - 5 p.m., EST, Friday.

Lowes.com

AB13132

TABLE OF CONTENTS

Safety Information ....................................................................................................................

Package Contents ....................................................................................................................

Preparation ...............................................................................................................................

Installation Instructions .........................................................................................................

Bulb Replacement .........................................................................................................

Care and Maintenance .........................................................................................................

Troubleshooting ....................................................................................................................

Warranty ..............................................................................................................................

SAFETY INFORMATION

Please read and understand this entire manual before attempting to assemble, operate or install

the product. If you have any questions regarding the product, please call customer service at

1-866-994-4148 8 a.m. - 6 p.m., EST Monday - Thursday, 8 a.m. -5 p.m., EST, Friday.

Understanding Hazard Signal Words:

DANGER: Indicates a potentially hazardous situation that, if not avoided, could result in

death or serious injury.

WARNING: Indicates a potentially hazardous situation that, if not avoided, may result in

damage to the product.

WARNING: READ AND UNDERSTAND ALL SAFETY AND OPERATING INSTRUCTIONS

IN THIS MANUAL BEFORE ATTEMPTING TO INSTALL OR OPERATE THIS PRODUCT.

DANGER: Consult a qualified electrician if you are not certain about the installation

process. All wiring must be installed in accordance with the National Electrical Code (Canadian

Electrical Code in Canada). Always install wiring connections in accordance with local code,

ordinances and the National Electrical Code. Please contact a qualified electrician if you have

any questions regarding the installation.

DANGER: Fixture must be connected to a 120-volt, 60 hertz power source.

DANGER: Turn power off at the circuit breaker or fuse box before

starting installation!

DANGER: DO NOT rely on wall switch alone to turn off power.

READ ALL INSTRUCTIONS! SAVE THESE INSTRUCTIONS!

Lowes.com

PACKAGE CONTENTS

Part Description Quantity

Fixture Housing Assembly with Ground Screw

Photocontrol

Lens Assembly

100-watt Metal Halide Type M90/E Bulb

Protective Screen

Cover Plate

AB Photocontrol Socket (pre-installed in part A)

(PRE-INSTALLED

IN PART A)

Lowes.com

PREPARATION

Before beginning assembly of product, make sure all parts are present. Compare parts with

package contents list and diagram above. If any part is missing or damaged, do not attempt to

assemble the product. Contact customer service for replacement parts.This light fixture is

designed to fit standard junction boxes as defined by the National Electrical Code. As an

alternative, this light fixture may be installed using conduit connection. Please contact a qualified

electrician if you have any questions regarding the installation. If any part is missing or damaged,

or you are unsure how to proceed with assembly, do not attempt to install or use the product.

Estimated Assembly Time: 30 - 60 minutes

Tools Required for Assembly (not included): Phillips screwdriver, small adjustable wrench, wire

cutters/strippers, power drill with 3/16 in. (4.8 mm) drill bit, step ladder. (not included).

HARDWARE CONTENTS

Quantity Picture

(Shown to size)

Part Description

1/4 in. x 2 in.

Lag Screw

M4 x 18

Screw

1/4 in.

Washer

Nut

Wire Nut 2

M4 x 4

Screw

GG (Preinstalled in Fixture Housing)

Lowes.com

INSTALLATION INSTRUCTIONS

DANGER: Fixture must be connected to a 120 Volt, 60 Hz power

source.

DANGER: Turn power off at the circuit breaker or fuse box before

starting installation!

DANGER: DO NOT rely on wall switch alone to turn off power.

Fig. 1

Step 1: Attach Fixture Housing Assembly

Select a location on a flat wall with structurally sound wood and from 10 to 25 feet (3 to 7.6 m)

from the ground. The wood should be at least one inch (25 mm) thick to safely secure the fixture.

The fixture (A) can be mounted with three lag screws (AA) and washers (BB) which are provided.

Using the fixture (A) as a mounting template, mark three mounting holes. We suggest drilling

3/16 in. (4.8 mm) pilot holes for the lag screws. Install the bottom two (AA) with washers (BB)

first. Screw in the lag screws (AA) so that there is about 3/8 in. (9.5 mm) of space under (BB).

Place (A) on these two (AA) and install the top (AA) and (BB). Tighten the top (AA) first, and then

tighten the remaining (AA) (see Fig 1).

OFF

Lowes.com

Fig. 3

Fig. 2

Step 2: Connect Supply Wiring

INSTALLATION INSTRUCTIONS continued

Secure your outdoor cable or flexible conduit to

the cover plate (E) with a fitting in accordance with

the National Electrical Code (Canadian Electrical

Code in Canada). Thread the black and white

fixture wires through the hole in (E) as shown (see

Fig 2). Connect the fixture wires to the service

wires using the wire nuts (FF) provided (black to

black and white to white). This fixture must be

grounded. Connect the service ground wire under

the head of the green ground screw and secure to

the fixture.

Step 3: Attach Cover Plate

Install (E). Secure with the screws (CC),

washers (DD) and nuts (EE) (see Fig 3).

Lowes.com

Fig. 4

INSTALLATION INSTRUCTIONS continued

Step 4: Attach Lens Assembly

Step 5: Install Bulb

Step 6: Attach Protective Screen

Install the lens assembly (C) with three

screws (GG) secured to the fixture (see

Fig 4).

Screw in the 100W Metal Halide type

M90/E bulb (D) provided.

Install protective screen (F). Hook notch

onto (C), lift and snap into place (see Fig

4).

Lowes.com

Fig. 5 Fig. 6

See installation steps 5 & 6

WARNING: Your Metal Halide Security Light is designed to operate safely with ONLY a 100-watt

metal halide type M90/E bulb.Replace with only a 100-watt Metal Halide type M90/E bulb.Installation

of any other bulb type may cause damage to the fixture.

DANGER: Turn power off at the circuit breaker or fuse box before

replacing bulb.

DANGER: DO NOT rely on wall switch alone to turn off power.

OFF

INSTALLATION INSTRUCTIONS continued

For optimal performance the arrow on the photocontrol (B) should be facing north after (A) is installed.

If adjustment is needed, loosen the screw in the center of the white photocontrol receptacle (AB) two

turns. Rotate (AB) so that the arrow will point north when installed and retighten screw. Note: There is

a stop to prevent (AB) from turning all the way around. If you have trouble turning (AB), try turning it in

the other direction.

Install (B) by aligning the arrow on top of (B) with arrow on (AB). Push down and twist clockwise.

CAUTION: (B) will only plug in one way. Align the large prong on (B) with the large opening in (AB).

BULB REPLACEMENT

Step 7: Install Photocell

To test operation during the daytime, cover (B). Turn the power on. Light should turn on and reach

full brightness within 10 minutes. Expose (B) to daylight. Light should turn off within two minutes.

With (B) exposed, the light will operate automatically: ON at dusk and OFF at dawn.

(Top View)

Lowes.com

Part Description Quantity

Ballast

Ignitor

Lamp socket

CARE AND MAINTENANCE

Ballast assembly replacment.

Quantity Picture

(Shown to size)

Part Description

M5 x 12

Screw

Washer

Wire Nut 5

M4 x 8

Screw

SA SB SC

Ballast assembly parts are installed and tested at the time of manufacture. No fur-

ther user assembly is needed.

Use a qualified electrician.

Ballast sub-assembly parts

SI Capacitor 1

M4 x 12

Screw 2

Lowes.com

The ballast assembly can be replaced without the cutting of any wires. Use a qualified electrician.

Perform ballast replacement after removing light fixture from the wall.

CARE AND MAINTENANCE

Ballast assembly replacment.

Step 1: Remove protective screen (F).

Step 2: Remove bulb (D).

Step 3: Loosen the three lens assembly

screws (GG) and remove lens assembly.

Step 4: Remove the two screws (SD)

and washers (SE) connecting the

ballast (SA) to fixture housing (A) (see

Fig 7).

DANGER: Turn power off at the circuit breaker or fuse box before

starting balast replacement.

DANGER: DO NOT rely on wall switch alone to turn off power.

OFF

Fig. 7

Lowes.com

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Utilitech Laterne Handbücher

Utilitech

Utilitech 0366096 Bedienungsanleitung

Beliebte Laterne Handbücher anderer Marken

KYOWA

KYOWA KW-9114 Bedienungsanleitung

Stahl

Stahl ECOLUX 6610 Series Bedienungsanleitung

SNOWJOE

SNOWJOE SUNJOE 24V-LGT500-CT Bedienungsanleitung

PRG

PRG VARI LITE VL5 Bedienungsanleitung

Raytec

Raytec VARIO2 series Bedienungsanleitung

ENSA

ENSA LEDBT18WS2 Bedienungsanleitung

LUG

LUG OFFICE LB LED N/T Bedienungsanleitung

GE Wallighter 250 Bedienungsanleitung

Draper

Draper RLEDL19/B Bedienungsanleitung

Green Lighting

Green Lighting TRI-SENSOR GL4612LU Bedienungsanleitung

Panasonic

Panasonic EY3741B57 Bedienungsanleitung

Clas Ohlson

Clas Ohlson LCC8T Bedienungsanleitung

Coolon

Coolon WDN-140 Bedienungsanleitung

Holiday Travel

Holiday Travel 834873 Bedienungsanleitung

BEGA

BEGA 84 036 Bedienungsanleitung

BEGA

BEGA 33 596 Bedienungsanleitung

Dale Tiffany

Dale Tiffany GT701162 Bedienungsanleitung

Wagan

Wagan Brite Nite Pop-Up USB Lantern Bedienungsanleitung