Utilitech 148003 Bedienungsanleitung

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

WARNING:

FOR YOUR PROTECTION, ALWAYS

DISCONNECT PUMP FROM POWER

SOURCE BEFORE HANDLING.

2 in. on

.4 in. off

Discharge

1-1/4 in.

Pipe

Base

1. Install the snap-

on strainer (C) by

lining up the pump

(A) base to match

the strainer. Push

down gently until it

latches.

2. Attach 1-1/4 in. pipe or

tting (not included) to

pump (A) discharge,

or screw the garden

hose adapter/check

valve (B) into the pump

discharge.

NOTE: Be sure the

garden hose adapter/

check valve is installed

with the word ‘Top’

facing up.

3. If using garden hose

(not included), thread

the female end of the

garden hose into the

male end of the garden

hose adapter (B).

For best performance,

unwind the hose before

starting the pump.

4. Place pump (A) in an

upright position on

the pool cover where

water will collect. Do

not suspend pump (A)

by the discharge hose

or power cord.

Be sure pump (A) is

not sitting in mud,

sand, or debris.

5. Plug the pump into a properly

grounded, GFCI 115 V

outlet. For safety, the pump

should always be electrically

grounded to a suitable

electrical ground, such as a

grounded water pipe, properly

grounded metallic raceway, or

ground wire.

6. The pump (A) will turn

on when the water

level around the pump

reaches approximately

2 in. Water must contact

the pump sensors in

order for it to turn on.

When the water level

drops to approximately

.4 in., pump (A) will run

for 10 additional seconds

and then turn o󰀨.

QUICK START GUIDE. SEE INSTRUCTION

MANUAL FOR COMPLETE DETAILS.

ITEM #0955587

UTILITY POOL COVER PUMP

MODEL #

148003

SW1181 B

Printed in China

Andere Handbücher für 148003

Inhaltsverzeichnis

Andere Utilitech Wasserpumpe Handbücher

Utilitech

Utilitech UT25PCP Bedienungsanleitung

Utilitech

Utilitech 148008 Bedienungsanleitung

Utilitech

Utilitech 148013 Bedienungsanleitung

Utilitech

Utilitech 148012 Bedienungsanleitung

Utilitech

Utilitech UT100USP Bedienungsanleitung

Utilitech

Utilitech UT2100IGPP Bedienungsanleitung

Utilitech

Utilitech 148008 Bedienungsanleitung

Utilitech

Utilitech PPWB Bedienungsanleitung

Utilitech

Utilitech PPTP1 Bedienungsanleitung

Utilitech

Utilitech #PPLSP100-SS Bedienungsanleitung

Utilitech

Utilitech 50AC-110N Bedienungsanleitung

Utilitech

Utilitech 148007 Bedienungsanleitung

Utilitech

Utilitech 148137 Bedienungsanleitung

Utilitech

Utilitech EFCWJ10-L Bedienungsanleitung

Utilitech

Utilitech PPSU33 Bedienungsanleitung

Utilitech

Utilitech 148003 Bedienungsanleitung

Utilitech

Utilitech 148003 Bedienungsanleitung

Utilitech

Utilitech 50AC-110 Handbuch

Utilitech

Utilitech PPWF50 Bedienungsanleitung

Utilitech

Utilitech PPTPC50 Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung