V-tech QW2432 Bedienungsanleitung

When using your telephone equipment, basic safety precautions should always

be followed to reduce the risk of fire, electric shock and injury to persons, including

the following:

1. Read and understand all instructions.

2. Follow all warnings and instructions marked on the product.

3. Unplug this product from the wall outlet before cleaning. Do not use liquid

cleaners or aerosol cleaners. Use a damp cloth for cleaning.

4. Do not use this product near water (for example, near a bath tub, kitchen

sink, or swimming pool).

5. Do not place this product on an unstable cart, stand, or table. The product

may fall, causing serious damage to the product.

6. Slots and openings in the cabinet and the back or bottom are provided

for ventilation. To protect it from overheating, these openings must not be

blocked by placing the product on the bed, sofa, rug, or other similar surface.

This product should never be placed near or over a radiator or heat register.

This product should not be placed in a built-in installation where proper

ventilation is not provided.

7. This product should be operated only from the type of power source

indicated on the marking label. If you are not sure of the type of power

supply to your home, consult your dealer or local power company.

8. Do not allow anything to rest on the power cord. Do not locate this product

where the cord will be abused by persons walking on it.

9. Never push objects of any kind into this product through cabinet slots as

they may touch dangerous voltage points or short out parts that could result

in a risk of fire or electric shock. Never spill liquid of any kind on the product.

10. To reduce the risk of electric shock, do not disassemble this product, but

take it to an authorized service facility. Opening or removing cabinet parts

other than specified access doors may expose you to dangerous voltages

or other risks. Incorrect reassembling can cause electric shock when the

appliance is subsequently used.

11. Do not overload wall outlets and extension cords as this can result in the

risk of fire or electric shock.

Important Safety Instructions

12. Unplug this product from the wall outlet and refer servicing to an authorized

service facility under the following conditions:

A. When the power supply cord or plug is damaged or frayed.

B. If liquid has been spilled into the product.

C. If the product has been exposed to rain or water.

D. If the product does not operate normally by following the operating

instructions. Adjust only those controls that are covered by the

operating instructions, because improper adjustment of other controls

may result in damage and will often require extensive work by an

authorized technician to restore the product to normal operation.

E. If the product has been dropped and the cabinet has been damaged.

F. If the product exhibits a distinct change in performance.

13. Avoid using a telephone (other than a cordless type) during an electrical

storm. There may be a remote risk of electric shock from lighting.

14. Do not use the telephone to report a gas leak in the vicinity of the leak.

SAVETHESE INSTRUCTIONS

Important Safety Instructions

The QW2432 is an advanced cordless telephone that operates in the 2.4GHz

frequency range. Your QW2432 is capable of supporting up to a maximum of

4 Handsets. Using additional Handsets, up to three people can be conferenced

on a call (2 Handsets and the Base Speakerphone), or two extensions can be

conferenced on a call, while two other extensions can be talking internally, using

the Intercom feature.

This manual is designed to familiarize you with the QW2432 cordless telephone.

To order additional Handsets (model QW2422) or headsets, call Qwest at

800-244-1111.

Introduction

IMPORTANT

Please record the Base ID#(BS ID) printed on the underside of the 2432 Base

in the space below. Please be certain to include all 15 digits/characters.

Base ID#

Parts Check List

5. Battery Pack

6. Wall Mounting Bracket

7. Belt Clip

8. Owner's Manual

1. Base Unit

2. Handset

3. AC Power Adapter

4. Telephone Cord

OWNER’S MANUAL

QW2432

The Handset Layout

1. Antenna

2. Message Waiting Indicator

3. Earpiece

4. Headset Jack (2.5mm)

5. Scroll Keys

6. On (Flash)

7. Dialing Key (0-9)

8. Handsfree Speakerphone

9. LCD Display

10. Select

11. Off (Clear)

12. Battery Compartment

13. Intercom

14. Services Key

15. Microphone

The Base Unit Layout

Phone Cord Jack

AC Power Jack

Messages Key

Dialing Keys (0-9)

Speakerphone Key

Message Waiting Indicator

In Use Indicator

Power Indicator

Charge Indicator

Mute Key

Hold Key

Flash Key

Redial Key

3-Way Calling Key

Cancel Call Waiting Key

Volume Keys

Charging Contacts

Page/Intercom Key

QW2432

Setup

Plug the AC power adapter into an electrical outlet, and the DC connector into

the back of the base unit.

Connecting to phone line

Plug one end of the telephone line cord into the jack on the back of the base

unit. Plug the other end of this cord into the wall jack.

Checking for dial tone

After the battery is charged press

on the Handset. The Phone icon

will appear on the handset display, and you will hear dial tone. If not, see In

Case of Difficulty.

Tone/Pulse selection

See BASE SETTINGS for details.

CAUTION: Use only the Qwest power supply provided with your Qwest

Unit.

To AC outlet

To telephone

jack

To telephone

socket outlet

AC adapter

IMPORTANT:

For best performance the QW2432

Should be installed as follows:

In an elevated location, in the center of

the room, with no obstructions nearby.

In a location that is away from other

electricalappliancessuchasmicrowave

ovens, personal computers, or

televisions.

Getting Started

Follow the steps below:

1. Remove the battery cover by

pressingon the indentand sliding

downward.

2. Place the new battery pack in the

handset with the metal contacts

aligned with the charge contacts

in the battery compartment.

3. Replace the battery cover by

sliding it upwards.

4. If the new battery pack is not

already charged, place the

handset in the base unit, or a

remotecharging stand, andallow

it to charge for 12 hours. After

initial charge, a maintenance

charge of 8 hours should be

sufficient.

Installation of Battery Pack in Handset

The original Handset that is shipped with your QW2432 system will be

automatically registered to the Base. This Handset is HANDSET 1.

As you register additional Handsets to the system, they will be assigned extension

numbers in the following order: HANDSET2, HANDSET3, and finally HANDSET

Whenever a Handset battery pack is installed, the Handset will automatically

begin SEARCHING FOR BASE (if previously registered), or it will prompt you

to ENTER BASE ID to register the new Handset.

Getting Started

Spare Battery Charger/Power Backup Function

The QW2432 can use a the spare battery in the Base Unit to provide operational

backup in the event of a power failure. With a fully charged battery pack in the

spare battery charger, you will still be able to place and receive calls from the

Handset for up to 5 hours.

The spare battery pack can also be used to replace a drained handset battery,

ensuring uninterrupted use.

A spare battery can be purchased from most retail stores that carry

electronic equipment.

NOTE :

When using the QW2432 during Power Backup mode, audio quality may be

compromised due to reduced Power availability.

CAUTION: TO

REDUCE RISK OF FIRE,

USE ONLY VTECH

80-5017-00-00

CAUTION: TO

REDUCE RISK OF FIRE,

USE ONLY VTECH

80-5017-00-00

BATTERY

INSTALL

THIS

SIDE UP

QW2432

1. Open the spare battery charger

by pressing the release button,

located on the right-hand side of

the Base Unit. A drawer will open

to reveal the spare battery

compartment.

2. Place a battery pack in the

drawer with the charge contacts

facing up and to the left.

3. Push the drawer closed.

The spare battery takes 24 hours to

fully charge a drained battery.

Getting Started

Charging Of Handset Battery Pack

The Handset of your QW2432 cordless telephone is powered by a rechargeable

battery pack. It charges automatically whenever the Handset is in the Base Unit.

You should charge the battery pack for 12 hours when you first receive

your phone. You'll know the battery pack needs charging when:

•The low battery message is displayed :

•The handset seems completely

dead, the LCD is completely

clear and does not activate when

you press the keys.

CAUTION:TOREDUCETHERISKOFFIREORINJURYTOPERSONS

BY BATTERY, READ AND FOLLOW THESE INSTRUCTIONS.

1. Use only the approprlate type and size battery pack specified in the

instruction manual provided for this product.

2. Do not dispose of the battery pack in a fire. The cell may explode. Check

with State and local codes for possible special disposal instructions.

3. Do not open or mutilate the battery pack. Released electrolyte is corrosive

and may cause damage to the eyes or skin. It may be toxic if swallowed.

4. Exercise care in handling battery in order not to short the battery with

conducting materials such as rings, bracelets, and keys. The battery or

conductor may overheat and cause burns.

5. Charge the battery pack provided with or identified for use with this product

only in accordance with the instructions and limitations specified in the

instruction manual.

6. Observe proper polarity orientation between the battery pack and battery

charger.

Inhaltsverzeichnis

Andere V-tech Schnurloses Telefon Handbücher

V-tech

V-tech DS6421-2 Bedienungsanleitung

V-tech

V-tech DECT 6.0 IS6100 Bedienungsanleitung

V-tech

V-tech DS6161 Bedienungsanleitung

V-tech

V-tech t 2435 Bedienungsanleitung

V-tech

V-tech 2431 - VT Cordless Phone Bedienungsanleitung

V-tech

V-tech FS6220-2 Bedienungsanleitung

V-tech

V-tech CS1500 Bedienungsanleitung

V-tech

V-tech i6725 Bedienungsanleitung

V-tech

V-tech sbc20-2432 Benutzerhandbuch

V-tech

V-tech T2340 - 2.4 GHz Dual Handset System Benutzerhandbuch

V-tech

V-tech DS6311-2 Bedienungsanleitung

V-tech

V-tech Three Handset Connect to CELL™ Answering System with Caller... Bedienungsanleitung

V-tech

V-tech T2451 - 2.4 GHz Analog Cordless Phone Bedienungsanleitung

V-tech

V-tech CS6909 Bedienungsanleitung

V-tech

V-tech VC7151 Bedienungsanleitung

V-tech

V-tech DS8141 Bedienungsanleitung

V-tech

V-tech vt9113 Bedienungsanleitung

V-tech

V-tech S1310 Bedienungsanleitung

V-tech

V-tech PDL GX Bedienungsanleitung

V-tech

V-tech Cordless Phone with Digital Answering System and Caller... Bedienungsanleitung

V-tech

V-tech LS6117-18 Bedienungsanleitung

V-tech

V-tech USB 7200 Bedienungsanleitung

V-tech

V-tech CS6858-33 Bedienungsanleitung

V-tech

V-tech VT1940 Bedienungsanleitung

Beliebte Schnurloses Telefon Handbücher anderer Marken

3Com

3Com NBX Bedienungsanleitung

Panasonic

Panasonic KX-TGK210HK Bedienungsanleitung

Panasonic

Panasonic KX-TCA181EX Bedienungsanleitung

BT FREESTYLE 3200 Bedienungsanleitung

AT&T

AT&T CL84102 Bedienungsanleitung

BREZZICNI

BREZZICNI CL-3622 Bedienungsanleitung

Panasonic

Panasonic KX-TG1831NZ Bedienungsanleitung

Panasonic

Panasonic KX-TG7301E Bedienungsanleitung

Furuno

Furuno FM-4721 Bedienungsanleitung

Sanyo

Sanyo CLT-J70 Bedienungsanleitung

Amplicomms

Amplicomms BigTel 201 Bedienungsanleitung

GE 26992 Bedienungsanleitung

AT&T

AT&T E1812B Bedienungsanleitung

Sanyo

Sanyo CLT-670 Bedienungsanleitung

GE 15432970 Bedienungsanleitung

Curtis

Curtis TC595 Bedienungsanleitung

Gigaset

Gigaset Gigaset 3000 Micro Bedienungsanleitung

Poly

Poly VVX D230 Einrichtungshandbuch