V-tech LS1250-B Bedienungsanleitung
User’s manual
www.euphones.vtech.com
LS1250-B
1
1. IMPORTANT SAFETY INSTRUCTIONS
When using your telephone equipment, basic safety precautions should always
be followed to reduce the risk of re, electric shock and injury, including the
following:
Read and understand all the instructions.
Follow all warnings and instructions marked on the product.
Unplug this product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
Do not use this product near water (for example, near a bath tub, kitchen
sink, swimming pool).
Do not expose the telephone to direct sunlight or extreme cold environment.
Do not put the telephone close to heating sources such as radiators,
cookers, etc.
Do not overload wall outlets and extension cords as this can result in the risk
of re or electric shock.
Unplug this product from the wall outlet and refer servicing to VTech/
distributor under the following conditions:
When the power supply cord or plug is damaged or frayed.
If the product does not operate normally by following the operating
instructions.
If the product has been dropped and the cabinet has been damaged.
If the product exhibits a distinct change in performance.
Avoid using a telephone (other than a cordless type) during an electrical
storm. There may be a remote risk of electric shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak.
Use only the supplied NiMH (Nickel Metal Hydride) batteries! The operation
periods for the handsets are only applicable with the default battery
capacities.
The use of other battery types or non-rechargeable batteries/primary cells
can be dangerous. These may cause interference and/or unit damages. The
manufacturer will not be held liable for damage arising from such
non-compliance.
Do not use third party charging bays. The batteries may be damaged.
Please note the correct polarity while inserting the batteries.
Battery should not be exposed to excessive heat such as bright sunshine or
re and immersed in water.
1.
2.
3.
4.
5.
6.
7.
•
•
•
•
8.
9.
10.
11.
12.
13.
14.
2
DISPOSAL WARNING
When this crossed-out wheeled bin symbol is attached to a
product, it means the product is covered by the European
Directive 2002/96/EC.
All electrical and electronic products/battery should be disposed
of separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.
The correct disposal of your old appliance/battery will help prevent potential
negative consequences for the environment and human health.
For more detailed information about disposal of your old appliance/battery,
please contact your city ofce, waste disposal service or the shop where you
purchased the product.
If you have questions about this product, or having difculty with setup or
operation, contact our Customer Service Centre.
POWER ADAPTOR INFORMATION
Power
adaptor
Ten Pao International Ltd. - Model: S003IV0600045,
Input 100-240V AC 50/60Hz 150mA,
Output 6VDC 450mA (EU plug).
Battery Handset: NI-MH PACK x1, 2.4V, 750mAh
Doorbell: ALKALINE CELL, AAx2, 1.5V; 2800mAh
For pluggable equipment, the socket outlet shall be installed near the equipment
and shall be easily accessible.
1.
2.
3.
3
2. SET UP THE TELEPHONE
2.1 Package Contents
The package contains the following items:
Telephone base and power adapter
Handset (1 for IS7121A, 2 for IS7121-2A)
Handset charger and charger adapter (1 for IS7121-2A)
Doorbell with wall mount cover
Telephone Wall mount bracket
Battery compartment cover (1 for IS7121A, 2 for IS7121-2A)
NiMH Rechargeable battery pack (1 for IS7121A, 2 for IS7121-2A)
AA Alkaline batteries (2)
Screw for doorbell (bottom)
Screw for doorbell (wall mount)
Wall anchors
Double-sided adhesive tape
Telephone line cord
User’s manual
Warranty card
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
4
2.2 Connect the Base Station
note
Use only the supplied power adapter.•
A DSL lter (not
included) is required
if you have DSL high-
speed Internet service.
The DSL lter must
be plugged into the
telephone wall jack.
To telephone
wall jack
To wall power
outlet
12
5
2.3 Install and Charge the Handset Batteries
notes
Use only the supplied NiMH rechargeable batteries.
If you do not use the handset for a long time, disconnect and remove the
batteries to prevent possible leakage.
•
•
Battery Pack
BT164392/BT264392
2.4V 550mAh Ni-MH
WARNING: DO NOT BURN OR
PUNCTURE BATTERIES
Made in China CR1222
1 2
3 4
CHARGE light
remains on
when charging.
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
CR1232
Battery Pack / Bloc-piles :
(2.4V Ni-MH)
WARNING / AVERTISSEMENT :
DO NOT BURN OR PUNCTURE BATTERIES.
NE PAS INCINÉRER OU PERCER LES PILES.
Made in China / Fabriqué en chine
THIS SIDE UP / CE CÔTÉ VERS LE HAUT
CR1232
6
2.4 Installation Options
Your telephone base is ready for tabletop use. If you want to mount your telephone
on a wall, follow the steps below to connect the telephone base with a standard
dual-stud telephone wall mounting plate. You may need a professional to install the
wall mounting plate.
2.4.1 Tabletop to Wall Mount Installation
If you have already installed the telephone for tabletop use, unplug the
telephone line cord from the telephone wall jack, and unplug the telephone
base power adapter from the wall outlet. Remove the telephone line cord and
the power adapter cord from the grooves.
1.
2. Route the telephone line cord through the rectangular hole on the wall mount
bracket. Position the lower portion grooves on the telephone base to the lower
portion tabs on the wall mount bracket. Make sure the upper portion grooves
of the telephone base are above the upper portion tabs on the wall mount
bracket. Push the telephone base down until it clicks securely in place.
7
3. Plug the telephone line cord into the telephone wall jack or DSL lter. Align the
holes on the bracket with the standard wall plate and slide the bracket down
until it locks securely.
4. Plug the power cord into an electrical outlet not controlled by a wall switch.
Bundle the telephone line cord and power adapter cord neatly with twist ties.
8
2.4.2 Wall Mount to Tabletop Installation
To change the telephone base from the wall mount position to tabletop position,
follow the steps below.
If the telephone line cord and power adapter cord are bundled, untie them rst.
Slide the wall mount bracket up and remove it from the wall plate. Unplug the
telephone line cord (or DSL lter) from the wall. Unplug the power adapter from
the power outlet.
Slide the telephone base up and remove it from the wall mount bracket.
See section Connect the Base Station.
1.
2.
3.
4.
9
2.5 Doorbell Battery Installation
Remove the wall mount cover at the back.
Install two AA batteries into the battery compartment, matching the polarity
markings (+ and -) inside the battery compartment.
1.
2.
Inhaltsverzeichnis
Andere V-tech IP-Telefon Handbücher
V-tech
V-tech LS6185A Bedienungsanleitung
V-tech
V-tech DS3111-2 - DECT 6.0 Cordless Phone Bedienungsanleitung
V-tech
V-tech ErisTerminal SIP Deskset VSP736 Bedienungsanleitung
V-tech
V-tech ErisTerminal ET635 Bedienungsanleitung
V-tech
V-tech VSP735 Bedienungsanleitung
V-tech
V-tech VSP735 Bedienungsanleitung
V-tech
V-tech VT9013 Bedienungsanleitung
V-tech
V-tech VSP608 Bedienungsanleitung
V-tech
V-tech ErisTerminal VSP726 Bedienungsanleitung
V-tech
V-tech IS8251 Bedienungsanleitung
V-tech
V-tech 15850 Bedienungsanleitung
V-tech
V-tech VT-DS6121 Bedienungsanleitung
V-tech
V-tech CM18445 Bedienungsanleitung
V-tech
V-tech DS6621 Bedienungsanleitung
V-tech
V-tech ErisTerminal VSP725A Bedienungsanleitung
V-tech
V-tech Vonage IP 8100-3 Bedienungsanleitung
V-tech
V-tech ErisTerminal SIP Deskset VSP736 Bedienungsanleitung
V-tech
V-tech CS6228-3 Bedienungsanleitung
V-tech
V-tech ErisTerminal ET605 Bedienungsanleitung
V-tech
V-tech LS6125 Bedienungsanleitung
