VADDIO CeilingVIEW 70 PTZ HideAway Bedienungsanleitung

Installation and User Guide

Camera and Electronic Products for Integrators

pricing are subject to change without notice. CeilingVIEW, WallVIEW ControlVIEW, EZCamera and PowerRite are registered

trademarks of Vaddio, Inc. All other trademarks are property of their respective owners. Form Number 341- 075 Rev. D

CeilingVIEW 70 PTZ HideAway

Installed PTZ Ceiling Camera with Recessed, Motorized Camera Lift System

Vaddio’s CeilingVIEW 70 PTZ HideAway camera system is

designed to provide system integrators with an easy to install,

recessed, in ceiling, motorized camera lift system (see Figure 1).

The system features a Sony® EVI-D70 PTZ Camera mounted into a

recessed, metal ceiling camera enclosure with ceiling tile support

and is equipped with Vaddio’s EZCamera™ Cabling System which

allows the integrator to use Cat. 5 cabling to run power, video and

camera control. The camera lift has a motorized extension arm,

that when retracted, conceals the camera. When the camera is

activated the extension arm lowers and reveals the camera.

Contact closure or voltage sensing can be used to activate the lift

system remotely or the camera IR remote control can be used to

activate the lift with the ON/OFF button. The VISCA control

interface is included to allow the camera to work with any other

VISCA compatible control device. The PowerRite™ power supply

regulates the right amount of power needed for the camera over the

Cat. 5 cabling.

Before operating the Vaddio CeilingVIEW 70 PTZ HideAway,

please read the entire manual thoroughly. The camera system was

designed, built and tested for use indoors with the provided power

supply. The use of a power supply other than the one provided or

outdoor operation has not been tested and could damage the

camera and/or create a potentially unsafe operating condition.

The information contained in this manual will help you install and

operate your Vaddio CeilingVIEW 70 PTZ HideAway. If these

instructions are misplaced, Vaddio keeps copies of Specifications,

Installation and User Guides and most pertinent product drawings

for the Vaddio product line on the website. These documents can

be downloaded from www.vaddio.com free of charge.

SAVE THESE

INSTRUCTIONS

INTENDED USE

INTRODUCTION

Figure 1: Vaddio

CeilingVIEW 70

PTZ HideAway

shown retracted

(left) and lowered

into operating

position (right)

CeilingVIEW 70 PTZ HideAway – Document 341- 075 Rev. D

Page 2 of 14

Read and understand all instructions before using. Do not operate

the camera if the camera has been dropped or damaged. In this

case, a Vaddio technician must examine the product before

operating. To reduce the risk of electric shock, do not immerse in

water or other liquids and avoid extremely humid conditions.

Carefully remove the device and all of the parts from the packaging.

Unpack and identify the following parts:

•One (1) CeilingVIEW 70 PTZ Camera Module

•One (1) White trim ring with IR sensor attached

•One (1) Vaddio Quick-Connect Box

•One (1) Sony RM-EV100 IR Remote Controller

•One (1) Vaddio PowerRite 18VDC Power Supply

•One (1) AC power cable for Power Supply

•One (1) 12’ (4.57m) S-Video cable

•One (1) 12’ (4.57m) Composite Video cable

•Two (2) Adjustable ceiling tile support rails

•One (1) RJ-45 to DB9 EZCamera™ serial control converter

•Mounting Hardware

•Installation and User Guide (341-075 Rev. C)

UNPACKING

Use only the power supply provided with the CeilingVIEW 70 PTZ

HideAway camera system. Use of any unauthorized power supply will

void any and all warranties.

IMPORTANT

SAFEGAURDS

INSTALLATION

REMOVE the safety tape and then REMOVE the shipping hold-down

screw in the back of the camera module as indicated below (see Figure 2.

If power (over the Cat. 5 POWER/VIDEO cable) is connected to the

camera before the shipping hold-down screw is removed, serious

damage to the camera may result.

Remove

Sticker

Camera Top

Power/Video

RJ-45 Jack

Remove

Shipping

Screw

Camera Top

Figure 2: Top of camera shown with safety tape (left) and location of

shipping hold down screw and Power/Video Jack (right).

CeilingVIEW 70 PTZ HideAway – Document 341- 075 Rev. D

Page 3 of 14

CAMERA

FRONT

CEILING TILE

The CeilingVIEW 70 PTZ HideAway is an integrated

document/object camera specifically designed for installation in a

suspended ceiling above a table or work surface. Recommended

ceiling heights are between 8 and 12 feet.

•Be sure to check above the ceiling tile where you plan to install

the camera to make sure the area is clear and that there is

enough room for the CeilingVIEW Camera Module and all of its

components.

•Keep in mind that other than viewing straight down, the

CeilingVIEW PTZ has the capability of panning +/-170 degrees

from center.

•The camera may be used with any 2’ tile. The camera module

enclosure and the tile support rails allow for flexibility and

positioning freedom when used with 2'x2' and 2'x4' ceiling tiles.

•For cutting ease, remove the marked ceiling tile and place on a

suitable and safe work surface.

Note: If camera is to be controlled as part of a multi camera system, please

refer to the section CHANGING CAMERA DEFAULT SETTINGS located on

Page 7 of this manual.

To mount the CeilingVIEW 70 PTZ HideAway:

1) Attach a string or plumb bob to the ceiling tile with a thumbtack.

2) Position the string directly over ample table space or work

surface to allow easy document and object positioning.

3) Using a sharp utility knife, score a 6-3/4" diameter circle into the

front of the tile centered on the string.

4) Carefully cut out the 6-3/4" hole.

5) Place the tile support rail on the backside of the tile and center

over the hole. Carefully place camera in cutout hole from the

back of tile (see Figures 3 and 4) and attach to support rails.

Getting

Started

Before

Installing

Step by Step

Mounting

Instructions

Figure 3:

Side View of CeilingVIEW

Camera Module

For installation reference,

the cutout area by the IR

detector cable hole is on

the side of the camera.

CeilingVIEW 70 PTZ HideAway – Document 341- 075 Rev. D

Page 4 of 14

6) Using the supplied thumbscrews and washers, attach the

support rails to the CeilingVIEW PTZ camera (see Figure 4).

Place rail edge between two washers and tighten thumbscrew

securely. Note: The thumbscrew sits on top of the rail, not through

the holes on the rail.

7) The Cat.5 cable (plenum rated as code dictates) is run from the

ceiling location where the camera is to be mounted, to where

the Quick-Connect Box is located (see Figure 5). Both the S-

Video and Composite Video outputs are active.

8) If needed, Cat.5 plenum rated cable(s) may be purchased from

Vaddio to connect your camera for video, power control and

control daisy-chaining between multiple cameras (see Figure 6).

CAMERA

THUMB SCREW

24" BRACKET

WASHERS

Figure 4:

Side View and Close-up

of Camera module and

support rail

Cabling the

Camera

S-Video

Output to

Display

Device

Composite

Video

Output to

Dis

Power from

PowerRite Power

Supply

Cat. 5 to/from

POWER/VIDEO

Jack on Camera

Module

Figure 5:

Quick-Connect

Box and

connections

Figure 6:

Daisy Chain Control

Connections between

cameras

(Vaddio Cameras shown, left to right:

CeilingVIEW 70 PTZ HideAway,

WallVIEW 70 PTZ and WallVIEW 50i

PTZ HideAway)

RS-232

Control

IN IN INOUT OUT

CeilingVIEW 70 PTZ HideAway – Document 341- 075 Rev. D

Page 5 of 14

CAMERA

CEILING TIL

IR board

connector

IR cable

and plug

Trim Ring

9) Connections (see Figure 7):

a. Attach the installed Cat.5 cable routed from the

POWER/VIDEO jack on the back of the camera to the

Quick Connect Box.

b. If a RS-232 control cable is to be used, it should be

attached to the RS-232 IN jack.

c. If a second or third camera is to be used, attach a cable to

the RS-232 OUT jack and route to the next camera.

10)The camera and ceiling tile should be carefully replaced in the

suspended ceiling at this time.

11)Locate the white trim ring assembly and plug the IR cable into

the IR board connector on the trim ring lip (see Figure 8). Take

care not to pull any more than about 2 inches of cable from the

camera enclosure. The connectors will fit together only one way

with a positive click. (Note: DO NOT hang the trim ring from the

camera by the IR cable) Carefully move trim ring into position on

bottom of ceiling tile while feeding IR cable back into camera

enclosure and secure with the two supplied white screws.

Finishing Up

Figure 7:

RJ-45 Connections on back

of Camera Module

•POWER/VIDEO

•RS-232 IN

•RS-232 OUT (for daisy-

chain control)

Figure 8:

Connecting the IR

sensor on Trim Ring

to the IR cable

Connections

CeilingVIEW 70 PTZ HideAway – Document 341- 075 Rev. D

Page 6 of 14

12) With the Cat.5 cable routed from the POWER/VIDEO jack on

the back of the camera to the Quick Connect Box, connect the

supplied Vaddio PowerRite power supply. The camera will lower

into position and the S-Video and Composite Video signals will

be live and viewable after the camera is fully lowered and in the

“Home” position (Reminder: Use of a power supply other than the

provided Vaddio power supply will void warranty and may cause camera

and equipment damage).

The Camera can be controlled with the Sony RM-EV100 IR Remote

Controller or through RS-232 using VISCA control protocols.

The Sony RM-EV100 IR Remote Controller controls the following

functions when used with a CeilingVIEW 70 PTZ HideAway (see

Figure 9). A fresh set of AA batteries (not included) should be

installed in the provided Sony remote control. To operate, aim

remote at camera and depress desired button.

If you are using a control system (i.e. Crestron or AMX), plug the

Cat.5 cable from the RS-232 IN jack on the camera to your control

system using the Cat.5 to DB9 serial adapter supplied by Vaddio. If

you are controlling more than one camera, plug the Cat.5 cable from

the RS-232 OUT jack on the first camera to the RS-232 IN jack on

the second camera. Repeat procedure if third camera is to be used.

If control of motor only is desired, there is an external connector

provided on the top of the camera. This contact is normally open

and the motor will be in the retracted state. By providing a contact

closure across this connection when power is available and

connected via the Cat. 5 POWER/VIDEO cable, the motor will lower,

Initial

Camera

Power Up

CONTROLLING

THE CAMERA

Figure 9:

RM-EV100 IR Remote Controller

•Power on/off

oOn = Lowers camera

oOff = Retracts the camera

•Camera Select: 1, 2, 3

•Focus: Auto

Manual (Near & Far)

•Zoom: Slow – Tele, Wide

Fast – Tele, Wide

•Back Light: Back Light Compensation

•Pan-Tilt: Left, Right, Up, Down, Reset

•Home: Home/Centered Position

•Position: Preset, Reset

•Presets: 6 (1 through 6)

•Cancel: Not Used

•L/R Direction Set: Std, Rev

IR Remote

Control

Systems

Motor Control

Only (limited

use)

CeilingVIEW 70 PTZ HideAway – Document 341- 075 Rev. D

Page 7 of 14

FRONT

IMAGE FLIP IR SELECT

COVER

PLATE

RETAINER

SCREWS

COVER

PLATE

COVER

PLATE OFF

but will not power up the camera. Release of the closure will retract

the camera. The IR Remote Controller or RS-232 commands can

power up and lower/retract the camera only. The mating connector

can be found at Radio Shack (in the US) under part number 274-226

(see Figure 10).

Please refer to Figure 11 for this procedure.

•Camera must first be lowered into place and power unplugged.

•Place camera on suitable work surface.

•Remove the 4 cover plate retainer screws.

•Carefully lift off cover plate while threading the IR cable back through hole.

•Looking between the rear of the EVI-D70 camera body and the interconnect

circuit board, locate the 2 switches (it may be necessary to slightly tilt the

camera assembly to get the best view of the switches).

•The default setting for the image flip function is ON. Move this switch to the

left to disable.

•The default setting for IR select is 1. If this to be camera number 2 in a 2

camera system, set this switch to position 2. If this camera is number 3 in a 3

camera system, set switch to positions3.

•Carefully thread the IR cable back through the cover plate and secure plate to

camera enclosure using the 4 retaining screws.

Motor Control Connection

Figure 10:

Motor Control connection

shown

Mating Connector –

Radio Shack # 274-226

CHANGING CAMERA

DEFAULT SETTINGS

Figure 11: Cover Plate Removal and default settings access

CeilingVIEW 70 PTZ HideAway – Document 341- 075 Rev. D

Page 8 of 14

Vaddio supplies this control specification for the CeilingVIEW 70 PTZ HideAway

camera. This VISCA control set (as used in Sony EVI cameras) is used in

conjunction with additional Vaddio control commands (see comment section on

Table 1) for added functionality of the camera lift.

Communication Speed: 9600 bps (default)

Start bit: 1

Stop bit: 1

Data bits: 8

Parity: None

The control codes for the CeilingVIEW 70 PTZ HideAway are the same codes

used with the EVI-D70 pan/tilt/zoom camera. Vaddio is not translating these

codes and does not add any translation or memory capability to enable use of the

EVI-D70 camera as a main or auxiliary camera with videoconferencing system

codecs or the associated IR remote controllers.

For best control results, use the provided RM-EV100 IR Remote Controller or the

VISCA Commands (detailed in Table 1 below) with an external control system.

Table 1: VISCA Command List

RS-232

Command Set Command Command Packet* Comments

AddressSet Broadcast 88 30 01 FF Address setting

IF_Clear Broadcast 88 01 00 01 FF I/F Clear

CommandCancel 8x 2p FF p: Socket No.(=1or2)

On 8x 01 04 00 02 FF Power ON – Lowers Camera Lift

Mechanism and Turns camera ON

CAM_Power

Off(Standby) 8x 01 04 00 03 FF Power OFF – Retracts Camera Lift

Mechanism and Turns camera OFF

Stop 8x 01 04 07 00 FF

Tele(Standard) 8x 01 04 07 02 FF No

Wide(Standard) 8x 01 04 07 03 FF

Tele(Variable) 8x 01 04 07 2p FF p=0（Low）～7（Fast）

Wide(Variable) 8x 01 04 07 3p FF

CAM_Zoom

Direct 8x 01 04 47 0p 0q 0r 0s FF pqrs: Zoom Position

D-Zoom On 8x 01 04 06 02 FF Digital Zoom ON/OFF

CAM_Dzoom

D-Zoom Off 8x 01 04 06 03 FF

Stop 8x 01 04 08 00 FF

Far(Standard) 8x 01 04 08 02 FF

Near(Standard) 8x 01 04 08 03 FF

Far(Variable) 8x 01 04 08 2p FF p=0（Low）～7（High）

Near(Variable) 8x 01 04 08 3p FF

Direct 8x 01 04 48 0p 0q 0r 0s FF pqrs: Focus Position

Auto Focus 8x 01 04 38 02 FF AF ON/OFF

Manual Focus 8x 01 04 38 03 FF

CAM_Focus

Auto/Manual 8x 01 04 38 10 FF

RS-232

MMAND LI

Communication

Specification *Communication Example:

For the VISCA Packet “8x 01 04 07 03 FF”

(CAM_Zoom_Wide), “x” corresponds with

the number and order of the camera in the

control chain (daisy chain) where x = 1 for

the first camera, x = 2 for the second

camera, etc…

Control

Disclaimer

Command List

CeilingVIEW 70 PTZ HideAway – Document 341- 075 Rev. D

Page 9 of 14

Command List

(Continued)

One Push Trigger 8x 01 04 18 01 FF One Push AF Trigger

Infinity 8x 01 04 18 02 FF Forced Infinity

Near Limit 8x 01 04 28 0p 0q 0r 0s FF pqrs: Focus Near Limit Position

Normal 8x 01 04 58 02 FF AF Sensitivity Norm/Low

AF Sensitivity

Low 8x 01 04 58 03 FF

CAM_ZoomFocus Direct 8x 01 04 47 0p 0q 0r 0s 0t 0u 0v

0w FF

pqrs: Zoom Position

tuvw: Focus Position

Auto 8x 01 04 35 00 FF Normal Auto

Indoor 8x 01 04 35 01 FF Indoor Mode

Outdoor 8x 01 04 35 02 FF Outdoor Mode

One Push WB 8x 01 04 35 03 FF One Push WB Mode

ATW 8x 01 04 35 04 FF Auto Tracing White Mode

Manual 8x 01 04 35 05 FF Manual Control Mode

CAM_WB

One Push Trigger 8x 01 04 10 05 FF One Push WB trigger

Reset 8x 01 04 03 00 FF R Gain Manual setting

Up 8x 01 04 03 02 FF

Down 8x 01 04 03 03 FF

CAM_RGain

Direct 8x 01 04 43 0p 0q 0r 0s FF pqrs: R Gain

Reset 8x 01 04 04 00 FF B Gain Manual setting

Up 8x 01 04 04 02 FF

Down 8x 01 04 04 03 FF

CAM_BGain

Direct 8x 01 04 44 0p 0q 0r 0s FF pqrs: B Gain

Full Auto 8x 01 04 39 00 FF Automatic exposure mode

Manual 8x 01 04 39 03 FF Manual control mode

Shutter Priority 8x 01 04 39 0A FF Shutter priority auto exposure mode

Iris Priority 8x 01 04 39 0B FF Iris priority auto exposure mode

CAM_AE

Bright 8x 01 04 39 0D FF Bright mode (Manual）

Auto 8x 01 04 5A 02 FF AutoSlowShutter ON/OFF

CAM_SlowShutter

Manual 8x 01 04 5A 03 FF

Reset 8x 01 04 0A 00 FF Shutter setting

（1/4sec～1/10000sec）

Up 8x 01 04 0A 02 FF

Down 8x 01 04 0A 03 FF

CAM_Shutter

Direct 8x 01 04 4A 00 00 0p 0q FF pq: Shutter Position

Reset 8x 01 04 0B 00 FF Iris setting

Up 8x 01 04 0B 02 FF

Down 8x 01 04 0B 03 FF

CAM_Iris

Direct 8x 01 04 4B 00 00 0p 0q FF pq: Iris Position

Reset 8x 01 04 0C 00 FF Gain setting

CAM_Gain

Up 8x 01 04 0C 02 FF

CeilingVIEW 70 PTZ HideAway – Document 341- 075 Rev. D

Page 10 of 14

Command List

(Continued)

Down 8x 01 04 0C 03 FF

Direct 8x 01 04 4C 00 00 0p 0q FF pqrs: Gain Position

Reset 8x 01 04 0D 00 FF Bright setting

Up 8x 01 04 0D 02 FF

Down 8x 01 04 0D 03 FF

CAM_Bright

Direct 8x 01 04 4D 00 00 0p 0q FF pqrs: Bright Position

On 8x 01 04 3E 02 FF Exposure Compensation ON/OFF

Off 8x 01 04 3E 03 FF

Reset 8x 01 04 0E 00 FF

Exposure Compensation amount setting

Up 8x 01 04 0E 02 FF

Down 8x 01 04 0E 03 FF

CAM_ExpComp

Direct 8x 01 04 4E 00 00 0p 0q FF pqrs: ExpComp Position

On 8x 01 04 33 02 FF Back Light Compensation

CAM_BackLight

Off 8x 01 04 33 03 FF

On 8x 01 04 59 02 FF Setting for AE

Off 8x 01 04 59 03 FF

CAM_SpotAE

Position 8x 01 04 29 0p 0q 0r 0s FF pq: X(0 to F) , rs: Y(0 to F)

Reset 8x 01 04 02 00 FF Aperture Control

Up 8x 01 04 02 02 FF

Down 8x 01 04 02 03 FF

CAM_Aperture

Direct 8x 01 04 42 0p 0q 0r 0s FF pqrs: Aperture Gain

On 8x 01 04 61 02 FF Mirror Image ON/OFF

CAM_LR_Reverse

Off 8x 01 04 61 03 FF

On 8x 01 04 62 02 FF Freeze Picture ON/OFF

CAM_Freeze

Off 8x 01 04 62 03 FF

Off 8x 01 04 63 00 FF Picture Effect setting

Neg.Art 8x 01 04 63 02 FF

CAM_PictureEffect

B&W 8x 01 04 63 04 FF

On 8x 01 04 01 02 FF ICR Mode ON/OFF

CAM_ICR

Off 8x 01 04 01 03 FF

On 8x 01 04 51 02 FF Auto ICR ON/OFF

CAM_AutoICR

Off 8x 01 04 51 03 FF

Reset 8x 01 04 3F 00 pp FF p: Memory number （=0 to 5）

Set 8x 01 04 3F 01 pp FF

CAM_Memory

Recall 8x 01 04 3F 02 pp FF

On 8x 01 04 75 02 FF Mute ON/OFF

Off 8x 01 04 75 03 FF

CAM_Mute

On/Off 8x 01 04 75 10 FF

CAM_Display On 8x 01 04 15 02 FF Display On/Off

Andere Handbücher für CeilingVIEW 70 PTZ HideAway

Inhaltsverzeichnis

Andere VADDIO Sicherheitskamera Handbücher

VADDIO

VADDIO Wallview CCU HD-20 HD-SD Bedienungsanleitung

VADDIO

VADDIO WIDESHOT WALLVIEW MINI 999-6911-100 Bedienungsanleitung

VADDIO

VADDIO RoboSHOT 12 Series Bedienungsanleitung

VADDIO

VADDIO RoboSHOT 12 HDMI Bedienungsanleitung

VADDIO

VADDIO ZOOMSHOT 20 Bedienungsanleitung

VADDIO

VADDIO CANON XU-81 Bedienungsanleitung

VADDIO

VADDIO 999-6900-000W Bedienungsanleitung

VADDIO

VADDIO CLEARVIEW HD-20SE Bedienungsanleitung

VADDIO

VADDIO WallVIEW CCU HD-19 Bedienungsanleitung

VADDIO

VADDIO WallVIEW PRO 300 Bedienungsanleitung

VADDIO

VADDIO WallVIEW CCU HD-19 Bedienungsanleitung

VADDIO

VADDIO WallView Bedienungsanleitung

VADDIO

VADDIO RoboSHOT HDBT Series Bedienungsanleitung

VADDIO

VADDIO CLEARVIEW HD-20SE Bedienungsanleitung

VADDIO

VADDIO RoboSHOT 12E HDBT Bedienungsanleitung

VADDIO

VADDIO ZOOMSHOT WALLVIEW SR 999-6918-001 Bedienungsanleitung

VADDIO

VADDIO WallVIEW 50i Bedienungsanleitung

VADDIO

VADDIO WALLVIEW DVI/HDMI HD-20 Bedienungsanleitung

VADDIO

VADDIO WALLVIEW DVI/HDMI HD-20 Bedienungsanleitung

VADDIO

VADDIO WALLVIEW DVI/HDMI HD-20 Bedienungsanleitung

VADDIO

VADDIO 999-9200-050 Bedienungsanleitung

VADDIO

VADDIO IntelliSHOT 999-21100-000 Bedienungsanleitung

VADDIO

VADDIO RoboSHOT HDMI Series Bedienungsanleitung

VADDIO

VADDIO RoboSHOT Bedienungsanleitung

Beliebte Sicherheitskamera Handbücher anderer Marken

Okina USA

Okina USA SIR36-870VF650LP Bedienungsanleitung

Divio

Divio NDR155PA Bedienungsanleitung

Canon

Canon VB-C500D Bedienungsanleitung

Easy Access

Easy Access EasyGuard Bedienungsanleitung

Vivotek

Vivotek FD9389-EHV-v2 Bedienungsanleitung

TUYA

TUYA COSMO W2 Bedienungsanleitung

Eusso

Eusso UNC7500-IR Einrichtungshandbuch

urmet domus

urmet domus 1096/204 Bedienungsanleitung

VC VC20 series Bedienungsanleitung

Axis

Axis Q1614 Bedienungsanleitung

ieGeek

ieGeek DD201 Bedienungsanleitung

Vicon

Vicon V662-D-1 Betriebsanleitung

Grundig

Grundig GCH-K0274P Bedienungsanleitung

Lorex

Lorex VANTAGE LBC7032 Bedienungsanleitung

4xem

4xem WPT Bedienungsanleitung

Samsung

Samsung SCV-3082 Bedienungsanleitung

Vitek

Vitek VTC-C544 Bedienungsanleitung

Lumens

Lumens VC-A50PNW Bedienungsanleitung