Valcom V-9947A Bedienungsanleitung

VSP-V-9947A

Issue 8

1947947

V-9947A

LINE POWERED LOUD RINGER/HORN

INTRODUCTION

The V-9947A, is a Line Powered Loud Ringer/Horn

which provides amplified electronic tones for signalling

in large or noisy areas. This instruction contains the

specifications and information necessary to install,

operate, and maintain the V-9947A.

This equipment has received FCC type KX registration

number and has a REN of 2.7A. The FCC Registration

Number, BAF9I7-19317-RG-N, will be listed in the

affidavits filed with the telephone company; it will also

be recorded in the system log kept by installation and

maintenance personnel. The local telephone company

is to be notified of the FCC Registration Number when

this equipment is installed.

SPECIFICATIONS

Design

The V-9947A is a ringer/horn containing circuitry to

generate incoming call indication via a warble or single

tone when activated by 70-120 Vac ring voltage

(Ringer Equivalency Number 2.7A).

To plan a system utilizing the V-9947A, refer to the

Ringer Distance Chart to determine approximate

distances covered. The number given (ft) is the side to

side distance for mounting the speakers. It is also the

distance in front of the speaker that a good quality

signal can be heard.

Applications

•C. O. audible ringing.

•Loud ring.

Features

•Omni-directional mounting bracket.

•Self-contained tone generator, amplifier, volume

control, and horn speaker.

•Single or warble tone output.

•Activated by 70-120 Vac ring voltage.

•Tones continuous for duration of ring cycle.

•Weatherproof.

•Units may be multipled for simultaneous access.

•Separate power supply not required.

Dimensions/Weight

•6.5"H x 8.2"W x 10.4"D, plus mounting bracket.

•(16.51cm H x 20.83cm W x 26.42cm D)

•3.3 lbs. (1.5 kg)

Power Requirements

•20-30 Hz, 35 mA maximum, however, the V-

9947A is line driven and a separate power supply

is not required.

Environment

•Temperature: -20 to +55 degrees C

•Humidity: 0-95% non-precipitating

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

2947947

INSTALLATION

Lead Connections

Connect the tip (green) and ring (red) leads of the ringer

to the corresponding leads of the telephone the ringer is

to be used in conjunction with.

•To produce a warble tone, the black and white

leads remain unconnected.

•To produce a single tone, connect the black and

white leads to each other (See Figure 3).

Connecting Speaker to Base

The speaker may be attached to the base before or after

the base is mounted.

•Loosen position adjustment knob.

•Insert the ball of the base into the socket of the

speaker.

•Tighten the position adjustment knob.

Mounting

The V-9947A should be mounted 12' to 25' high to

obtain optimum results. This ringer may be used for

either interior or exterior signalling applications.

•Mount the base to a wall using the two holes

provided. Knockout holes are provided for punch

out should additional holes be desired.

•A "C" clamp is provided with the ringer to allow

mounting to a beam. Place the bolt through the

hole in the bottom of the base to secure the "C"

clamp to the beam. (See Figure 1). It is suggested

that the horn be mounted to the underside of the "I"

beam so as to provide the maximum of positioning

adjustments.

•Connection to an electrical backbox is

accomplished by channeling wire through the ball

of the base and making appropriate connections.

The base has holes punched for a double-gang

square box, but by punching out additional

knockout holes, the base can be mounted to a

single-gang or octagon box. (See Figure 2).

The V-9947A may be rotated or moved up and down to

obtain the desired position by loosening the position

adjustment knob at the bottom of the unit (See Figures

1 and 2) approximately 1 turn. Make required

adjustment and re-tighten the knob.

TECHNICAL ASSISTANCE

When trouble is reported, verify there are no broken

connections between the telephone and the ringer.

Ascertain volume control is turned up.

Assistance in troubleshooting is available from the

factory. When calling, you should have a VOM and a

test set available and be calling from the job site. Call

(540) 427-3900 and ask for Technical Support, or call

(540) 427-6000 for Valcom 24-hour Automated

Support or visit our website at http://www.valcom.com.

Valcom equipment is not field repairable. Valcom, Inc.

maintains service facilities in Roanoke, VA. Should

repairs be necessary, attach a tag to the unit clearly

stating company name, address, phone number, contact

person, and the nature of the problem. Send the unit to:

Valcom, Inc.

Repair and Return Dept.

5614 Hollins Road

Roanoke, VA 24019-5056

100

10 20 30 40 50 60 70 80 90 100 110 120 ft.

Distance

(

acin

in Feet

Ambient

Noise

Level

(dB)

RINGER DISTANCE CHART

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

3947947

I-Beam

"C" Clamp

Speaker Base

Position

Adjustment

Knob

Figure 1 - Mounting to a Beam with a "C" Clamp

Electrical

Backbox

Position

Adjustment

Knob

Wire

Speaker

Base

ure 2 - Mountin

to an Electrical Backbox

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

4947947

VALCOM LIMITED WARRANTY

Valcom, Inc. warrants its products to be free from defects in materials and workmanship under conditions of normal use and service for

a period of one year from the date of shipment. The obligation under this warranty shall be limited to the replacement, repair or refund

of any such defective device within the warranty period, provided that:

1. inspection by Valcom, Inc. indicates the validity of the claim,

2. the defect is not the result of damage, misuse, or negligence after the original shipment,

3. the product has not been altered in any way or repaired by others and that factorysealed units are unopened

(A service charge plus parts and labor will be applied to units defaced or physically damaged),

4. freight charges for the return of products to Valcom are prepaid,

5. all units 'out of warranty' are subject to a service charge. The service charge will cover minor repairs

(Major repairs will be subject to additional charges for parts and labor).

This warranty is in lieu of and excludes all other warranties, expressed or implied, and in no event shall Valcom, Inc. be liable

for any anticipated profits, consequential damages, loss of time or other losses incurred by the buyer in connection with the

purchase, operation or use of the product.

This warrantyspecifically excludes damage incurred in shipment. In the event a product is received in damaged condition, the carrier

should be notified immediately. Claims for such damage should be filed with the carrier involved in accordance with the F.O.B. point.

Headquarters:

Valcom, Inc.

1111 Industry Avenue

Roanoke, VA 24013

Phone: (540) 427-3900

FAX: (540) 427-3517

In Canada:

CMX Corporation

35 Van Kirk Drive #11 and 12

Brampton, Ontario L7A1A5

Phone: (905) 456-1072

FAX: (905) 456-2269

Tip

Ring

Green

Red

White

Black

V-9947A

To C. O. Line

or Analog

Station Port

Connect together to

produce single tone.

Warble tone is produced

when not connected.

FIGURE 3

Technical Manuals Online! - http://www.tech-man.com

firealarmresources.com

Andere Valcom Horn Handbücher

Valcom

Valcom VIP-480AL Bedienungsanleitung

Valcom

Valcom FlexHorn V-1030M Bedienungsanleitung

Valcom

Valcom V-1090 Flexhorn Bedienungsanleitung

Valcom

Valcom VIP-130AL-IC Bedienungsanleitung

Valcom

Valcom Revolution VIP-142-SA Bedienungsanleitung

Valcom

Valcom VIP-480AL-SA Bedienungsanleitung

Valcom

Valcom VIP-142 Bedienungsanleitung

Valcom

Valcom IP Solutions VIP-483 Bedienungsanleitung

Valcom

Valcom V-1050C Bedienungsanleitung

Valcom

Valcom V-1069 Bedienungsanleitung

Valcom

Valcom VIP-130L-IC Bedienungsanleitung

Valcom

Valcom V-1080 Flexhorn Bedienungsanleitung

Valcom

Valcom V-1048C Bedienungsanleitung

Valcom

Valcom V-1090 Flexhorn Bedienungsanleitung

Valcom

Valcom VIP-148AL-IC Bedienungsanleitung

Valcom

Valcom V-1048B Bedienungsanleitung

Valcom

Valcom InformaCast VIP-148L-IC Bedienungsanleitung

Valcom

Valcom VIP-148AL Bedienungsanleitung

Valcom

Valcom PagePac V-5331200 Bedienungsanleitung

Valcom

Valcom Flexhorn VIP-490AL-IC Bedienungsanleitung

Valcom

Valcom V-1030C Bedienungsanleitung

Valcom

Valcom V-1038 Bedienungsanleitung

Valcom

Valcom V-1069A Bedienungsanleitung

Valcom

Valcom V-9945A Bedienungsanleitung

Beliebte Horn Handbücher anderer Marken

Elk Products

Elk Products 45 Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock DB3 Series Bedienungsanleitung

Altec Lansing

Altec Lansing 811B HF HORN Bedienungsanleitung

RF Elements

RF Elements UltraHorn CC Series Bedienungsanleitung

Edwards Signaling

Edwards Signaling 869DSTR-G1 Series Montageanleitung

Electro-Voice

Electro-Voice HPT94 Bedienungsanleitung

Toa

Toa LE-M124 Bedienungsanleitung

EAW

EAW MR-102B Bedienungsanleitung

AUSTRALIAN MONITOR

AUSTRALIAN MONITOR MH30 Bedienungsanleitung

Pequod

Pequod TWISTER 3.1 Bedienungsanleitung

United Pacific

United Pacific 46151 Bedienungsanleitung

Wolo

Wolo OCEAN ALERT 170 Bedienungsanleitung

Vixen Horns

Vixen Horns VXO8315B/4114B Bedienungsanleitung

Altec

Altec 151A PAGING HORN Bedienungsanleitung

aidapt

aidapt VM953 Programmierhandbuch

auna

auna MEG1-HY Bedienungsanleitung

ACR Electronics

ACR Electronics ACR-EM-1A - REV Y Montageanleitung

Behringer

Behringer Eurosound Megaphone XT Bedienungsanleitung