Valor 975 Bedienungsanleitung
Page 1 of 5
#975 ZERO CLEARANCE KIT
Sept 2003
INSTALLATION INSTRUCTIONS
approved for use only with VALOR MODEL 922 Adorn Fireplace
1. GENERAL
Model 975ZCK zero clearance kit must be used when installing Fireplace Model 922 into
an enclosure constructed of combustible material and connected to an approved venting
system. Either the 923 Adorn or the 539/549 Windsor Arch cast fronts may be used with
the 922 fireplace installed in the 975 Zero Clearance Kit.
2. FRAMING.
Minimum clearances to combustible materials and framing details are shown in fig.1.
Though not mandatory, we recommend that a hard surfaced hearth area be maintained in
front of the fireplace for both aesthetic and maintenance purposes. This may be finished
in brick, ceramic tile, marble, etc. Raising the hearth slightly will help to minimize dust
and lint accumulation under the unit. Refer to the 922 installation manual for mantle
clearances as they vary with the different from trims.
To enable the heater to be installed correctly the height of the finished hearth must
be known before installing this kit, please note the bottom of the kit must be
installed at the planned finished hearth height (including tile etc.).
Fig. 1 framing dimensions
4000 483
Page 2 of 5
3. ZERO CLEARANCE KIT COMPONENTS
The complete #975ZCK contains the following:
Fig. 2 Kit parts
•Double wall
Z.C box
•Top shield
•Sheet metal
cement board
support
•4-top stand-
offs
•4” dia. vent
connector
•4” dia. x 14”
long Alu flex
liner.
•2 - 4” dia. S.S
gear clamps
•Bag of screws
4. ASSEMBLE THE ZERO CLEARANCE KIT
•Push the vent connector through the top of the zero clearance box, long side down,
and secure using three screws.
•Secure the top shield to the zero clearance box using six sheet metal screws (see fig
2)
•Secure the standoffs to the top spacer using 16 screws (fig 2).
Page 3 of 5
•5. SECURE THE ZERO CLEARANCE KIT TO THE FRAMING
•Place the kit in the framing. Note – bottom of the zero clearance kit should be installed
flush with the top of finished hearth. Allow for raised hearth.
•Hook the sheet metal cement board support over the top flange and secure through two
holes. ( see fig 3 )
•Secure the front flange of the zero clearance kit to the framing.( see fig 3 )
•Connect 4” dia “B” type vent to the vent connector on top of the zero clearance box.
•Attach the 4” dia flex liner to the vent connector, located on the underside of the top
panel, using one of the gear clamps provided.
•Non-combustible material (i.e. wonder board, cement board, etc.)
must be attached to the framing and the front flanges of the zero
clearance box as shown in fig. 4.
•All wall and hearth finishes may now be applied.
Fig.3. ZC kit installed in framing
Page 4 of 5
6. Finishing the Wall
Fig.4 Non combustible material location.
923 Adorn Front
Non-Combustible material such as Wonderboard must be used around the perimeter of the Z.C
Kit to the extents shown in fig 4. Combustible mantles (in some cases) may be allowed within
the perimeter of the Wonderboard – refer to the 922 installation
manual for mantle clearances for the various front trims.
Drywall/Sheetrock may be used beyond the perimeter of the
Wonderboard .
539 Windsor Arch Front with Plate
7. INSTALLING THE APPLIANCE
The unit can now be installed exactly as in a masonry
fireplace, see 922 installation and owner’s manual. Refer
to installation manual for mantle clearances as they vary
with the different front trims.
Please note that the second gear clamp, supplied with
this kit, and is to secure the 4” dia flex. vent to the
vent collar on the appliance.
549 Windsor Arch Front w/o Plate
Page 5 of 5
PLEASE LEAVE INSTALLATION AND OPERATING INSTRUCTIONS WITH THE
HOMEOWNER.
LIMITED WARRANTY POLICY
Miles Industries Ltd. warrants all components of the model 975 zero clearance kit for a period of two years from the
date of purchase against defects in materials or workmanship. This warranty covers only the cost of defective parts
and applies only to the original consumer purchaser. The replacement of defective parts by Miles Industries Ltd.
will be without charge during the warranty period. This warranty does not extend to (1) components damaged by
accident, neglect, misuse, abuse, alteration, and negligence of others, including the installation thereof by
unqualified installers’ (2) the costs of removal, reinstallation or transportation of defective parts or (3) incidental or
consequential damages.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED,
INCLUDING THE WARRANTY OF MERCHANTABILITY OF FITNESS FOR PURPOSE AND OF ALL
OTHER OBLIGATIONS OR LIABILITIES. MILES INDUSTRIES LTD DOES NOT ASSUME, NOR HAS IT
AUTHORIZED ANY PERSON INCLUDING ITS SALES REPRESENTATIVES TO ASSUME FOR IT, ANY
OTHER OBLIGATION OR LIABILITY IN CONNECTION WITH THE SALE OR USE OF THE MODEL 975
ZERO CLEARANCE KIT.
The model 975 zero clearance kit must be installed by a qualified installer in accordance with the instructions
furnished. The defective components should be returned at your expense to the dealer from where the product was
purchased or authorized service agent. Any components returned for warranty repair/replacement must be
accompanied by the sales invoice evidencing proof of purchase and date of purchase. Miles Industries Ltd. reserves
the right to repair and return any defective component.
Manufactured and distributed in Western Canada and USA by
Miles Industries Ltd.
829 West Third Street, North Vancouver B.C, CANADA, V7P 3K7
Ph. (604) 984-3496 Fax (604) 984-0246
Copyright 2003
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Valor Kaminzubehör Handbücher
Valor
Valor 1600J L1 Bedienungsanleitung
Valor
Valor LEGEND G3 Series Bedienungsanleitung
Valor
Valor L2 1700K Bedienungsanleitung
Valor
Valor 1100IN Bedienungsanleitung
Valor
Valor GV60NTK Montageanleitung
Valor
Valor LINEAR SERIES Bedienungsanleitung
Valor
Valor LX2 Series Bedienungsanleitung
Valor
Valor H3 Series Bedienungsanleitung
Valor
Valor LEGEND G3 763BPB Bedienungsanleitung
Valor
Valor 555CFK Bedienungsanleitung
Valor
Valor 1240BPK Bedienungsanleitung
Valor
Valor H6 Series Bedienungsanleitung
Valor
Valor BSK645 Bedienungsanleitung
Valor
Valor 739-72ILN/P Montageanleitung
Valor
Valor L1 Series Bedienungsanleitung
Valor
Valor G3 Series Bedienungsanleitung
Valor
Valor 720SWK Bedienungsanleitung
Valor
Valor 746CTK-VIK Bedienungsanleitung
Valor
Valor 1595CFKV2 Handbuch
Valor
Valor L3 Bedienungsanleitung
Beliebte Kaminzubehör Handbücher anderer Marken
Town & Country Fireplaces
Town & Country Fireplaces 22150051 Bedienungsanleitung
Travis Industries
Travis Industries 33 DVI Bedienungsanleitung
Superior
Superior ASD3628-TI Bedienungsanleitung
pleasant hearth
pleasant hearth OFP28WG Bedienungsanleitung
IHP
IHP Astria Series Bedienungsanleitung
Firegear
Firegear FG-H-2110SS Bedienungsanleitung
