Valor LT2 2700K Bedienungsanleitung

Valor Fireplaces • 190—2255 Dollarton Highway • North Vancouver, BC • V7H 3B1

Tel: 604.984.3496 or 1.800.468.2567 • Fax: 604.984.0246 or 1.800.268.0333

www.valorﬁreplaces.com

October 2023

1/3

Cement Board

LT2 2700K

Material Speciﬁcations

Non-Combustible

Material which will not ignite and burn. Such materials

are those consisting entirely of steel, iron, brick, tile,

concrete, slate, glass or plasters, or any combination

thereof.

Materials that are reported as passing ASTM E 136,

Standard Test Method for Behavior of Materials in a

Vertical Tube Furnace at 750°C shall be considered

non-combustible materials.

Combustible

Materials made of or surfaced with wood, compressed

paper, plant ﬁbers, plastics, or other material that

can ignite and burn, whether ﬂame proofed or not,

or plastered or unplastered shall be considered

combustible materials.

Non-Combustible Cement Board

The LT2 Linear ﬁreplace requires a 1/2” (13mm) thick

non-combustible cement board to be used as a wall

surface immediately surrounding the unit’s opening—

see diagram for minimum coverage.

Extending the cement board well beyond the minimum

shown will help avoid cracking due to diﬀerential

expansion of materials.

Pre-drill cement board with oversized holes and do

not over-tighten screws to avoid cracking due to heat

expansion.

Standard gypsum wall board may be used beyond the

perimeter of the cement board.

inches [mm] With 2775LFB trim With 2730CIK trim

AMin. 20-1/2 [521] Min. 20-1/8 [511]

B19-5/8 [498] 21 [533]

CMin. 8-11/16 [221] Min. 8 [203]

DMin. 4 [102] Min. 3-3/8 [84]

EMin. 49-13/16 [1265] Min. 51 [1296]

Min. 58” (1473 mm)

Min. 47-3/8” (1203 mm)

Flush with bottom of unit;

add extra cement board

if overlapping framing.

Minimum coverage area of non-combustible board.

Any wall nish applied to shaded area must be non-combustible.

LT2 replace outline

(including stand-os)

Non-combustible

board required

thickness:

1/2 inch (13 mm)

Joints preferred at corners

to prevent cracking

(see page 3)

Valor Fireplaces • 190—2255 Dollarton Highway • North Vancouver, BC • V7H 3B1

Tel: 604.984.3496 or 1.800.468.2567 • Fax: 604.984.0246 or 1.800.268.0333

www.valorﬁreplaces.com

Wall Finish — Trims

October 2023

2/3

LT2 2700K

Finishing Over Non-Combustible Board

Additional material such as tile, etc., may be applied

over top of the non-combustible board or you may

choose to leave it ﬁnished clean with no tile, etc.

Be aware that a trim is always required. Finish should

not cover the trims.

2775LFB Trim

Only the 2775LFB style trim will accept tile, etc. tucked

behind it (up to 1/2” thick for the 2775LFB).

2730CIK Trim

The 2730CIK trim must be installed BEFORE non-

combustible board. Non-combustible board and

ﬁnishes are applied to the perimeter of the trim frame.

Non-combustible board and ﬁnish CANNOT be tucked

under this trim.

Clean Installation

Kit (2730CIK) does

not adjust forward.

Non-combustible

board ﬁnishes up

to perimeter of

the trim. Must be

installed before

ﬁnish.

Narrow trim

(2775LFB) can adjust

up to 1/2” forward

of surface of non-

combustible board

lean Installation

(

2730CIK

)

does

ot ad

ust

orward.

on-combustible

oard

ﬁ

nishes u

erimeter o

he trim. Must be

installed be

ﬁ

nish.

Nar

row tr

(

2775LFB) can ad

to 1/2”

orward

sur

ace o

non-

ombustible boar

Valor Fireplaces • 190—2255 Dollarton Highway • North Vancouver, BC • V7H 3B1

Tel: 604.984.3496 or 1.800.468.2567 • Fax: 604.984.0246 or 1.800.268.0333

www.valorﬁreplaces.com

Wall Finish — Avoid Cracking

October 2023

3/3

LT2 2700K

Cracks

Provide joints

either here or

here

Avoiding Cracking Wall Finishes

If a clean ﬁnish with no tile, etc. is desired, joints in the

non-combustible board and the transition to gypsum

board will require special attention if future cracking

is to be controlled. Be aware that temperatures on the

non-combustible wall surface above the appliance can

approach 200°F (93°C).

Below are some tips on how to best avoid any cracking:

• Allow materials to dry thoroughly before ﬁnishing the

wall. Non-combustible board has the ability to absorb

up to 30 percent of its weight in water and may shrink

as much as 1/8” over a 48” length when drying from

a saturated condition. Running the ﬁreplace for an

extended period before ﬁnal ﬁnishing will help drive

out moisture.

• Always pre-drill screw holes through non-combustible

board and use screws with self-milling head.

• Always use mesh tape over joints.

• Always stagger joints in wall board.

• Behind joints, double up studs or use studs “on the

ﬂat” to add extra support to the joint. Adhesive on

the backside of wall board behind any joints can help

control diﬀerential movement.

• Use multiple, thinner coats of joint compound and al-

low to dry thoroughly between coats.

• Ensure framing materials are dry.

• After ﬁnishing the wall, introduce heat gradually to

slowly dry any excess moisture rather than drying too

fast.

• Avoid notching non-combustible board or tiles around

corners of window opening and instead provide a joint

that intersects the corner.

• Avoid using large one-piece slab of material with a

cut-out in the middle as a surround for the ﬁreplace.

Expansion above the opening will cause cracking at

inside corners. Provide a joint that intersects the inside

corner to avoid cracking.

WARNING:

HeatShift System MUST be installed on this

appliance.

Andere Valor Kaminzubehör Handbücher

Valor

Valor 784EC Bedienungsanleitung

Valor

Valor Portrait 549 Series Bedienungsanleitung

Valor

Valor 546LFB ZC Portrait Ledgeview Front Bedienungsanleitung

Valor

Valor LEGEND G3 Series Bedienungsanleitung

Valor

Valor 748CTK-VIK Bedienungsanleitung

Valor

Valor Legend G4 Series Bedienungsanleitung

Valor

Valor 1435 Bedienungsanleitung

Valor

Valor PORTRAIT BSK578 Barrier Screen Kit Bedienungsanleitung

Valor

Valor 757 Bedienungsanleitung

Valor

Valor PORTRAIT BSK539-549-550 Bedienungsanleitung

Valor

Valor LINEAR SERIES Bedienungsanleitung

Valor

Valor 1100IN Bedienungsanleitung

Valor

Valor LX1 Series Bedienungsanleitung

Valor

Valor H6 Series Bedienungsanleitung

Valor

Valor G3.5 Series Bedienungsanleitung

Valor

Valor 1600J L1 Bedienungsanleitung

Valor

Valor BSK613 Bedienungsanleitung

Valor

Valor LT1 Series Bedienungsanleitung

Valor

Valor 720SWK Bedienungsanleitung

Valor

Valor L2 SERIES Bedienungsanleitung

Valor

Valor Legend G4 Series Bedienungsanleitung

Valor

Valor L2 1700K Bedienungsanleitung

Valor

Valor L2 SERIES Bedienungsanleitung

Valor

Valor L2 SERIES Bedienungsanleitung

Beliebte Kaminzubehör Handbücher anderer Marken

Exodraft

Exodraft Xzense Bedienungsanleitung

Whalen

Whalen Ruso MNFP62BF23-6 Bedienungsanleitung

Lopi

Lopi Hearthview 864 Bedienungsanleitung

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Bedienungsanleitung

EdilKamin

EdilKamin SERBATOIO 250 Kurzanleitung

Bronpi

Bronpi KIT-1 Bedienungsanleitung

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Bedienungsanleitung

Travis Industries

Travis Industries 33 DVI Bedienungsanleitung

Superior

Superior ASD3628-TI Bedienungsanleitung

pleasant hearth

pleasant hearth OFP28WG Bedienungsanleitung

IHP

IHP Astria Series Bedienungsanleitung

Firegear

Firegear FG-H-2110SS Bedienungsanleitung

Nibe

Nibe Contura C i31 Bedienungsanleitung

kozy heat

kozy heat KZK-052 Bedienungsanleitung

SimpliFire

SimpliFire SF-WM36 Bedienungsanleitung

Bluegrass Living

Bluegrass Living BC18NR Kurzanleitung

pleasant hearth

pleasant hearth IRIS SCROLL Bedienungsanleitung

Cooke

Cooke Glass Wind Guard Bedienungsanleitung