Valor 530 536CXB Installations- und Betriebshandbuch

4001168/02

Note: This kit must be installed or serviced by a qualied installer, service agency or gas supplier.

These instructions are to be used in conjunction with the main installation instructions for the

above listed heater models.

WARNING: If the information in these instructions is not followed exactly, a re or explosion

may result causing property damage, personal injury or loss of life.

FOR PRESIDENT ZC INSTALLATION WITH A VALOR 530 ENGINE.

FOR 530 ENGINE CONFIGURATIONS AND VENTING,

REFER TO MAIN INSTALLATION BOOKLET SUPPLIED WITH THE

ENGINE.

#536CXB

President ZC Cast Front

CSA approved for use only with

Valor 530

Model Heaters

INSTALLATION BOOKLET

Designed and manufactured by / for

Miles Industries Ltd.

190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1

Tel. (604) 984-3496 Fax (604) 984-0246

www.milesreplaces.com

INSTALLER: Leave this manual with the appliance.

CONSUMER: Retain this manual for future reference.

Casting Tolerances

Due to the nature of cast iron, dimensional consistency may vary from one unit to the next and some variation

in surface nish and atness is to be expected. We have done our best to control and make allowance for this;

however some variation is inevitable.

1 Front Casting Assembly

1 Top Bafe

1 Framing Plate w/Brackets

1 Plinth

1 Rear Base Support

1 ZC stand-off LH

1 ZC stand-off RH

1 Insulation Layer

1 Pack of Screws

Kit Contents

Top Baffle

Front Casting Rear Base Support

Plinth

Stand-offs (2)

Insulation

Framing Plate

w/Brackets

26”

(framing plate)

31-1/4”

21-3/4”

(cast front)

27-7/8”

7/8”

High

raised

plinth

Ceiling ‘A’

‘B’ 1”max.

1/2”min.

1”max.

1/2”min.

11”min.

36”min.

36” min. to

combustibles

9”

Mantel

Optional Top Outlet

ZC Stand-offs

6-5/8”dia.

6-5/8”

dia.

21-5/8”

25-1/4”

31”

5” 7/8”

plinth

insul.

2”

26-1/4”

20”

26”

11”

9”

5”

‘D’

‘E’

Mantel

leg

See table

2”

Mantel depth “A” Min. clearance “B”

Up to 7” 4”

Above 7” up to 8” 5”

Above 8” up to 9” 7”

Above 9” up to 10” 8”

Above 10” up to 12” 9”

More than 12” 9”+extra 1” for every

1” depth above 12”

Mantel leg

projection “D”

Min. clearance from

appliance side “E”

Up to 8” 0”

More than 8” 6”

Dimensions &

Clearances

The Valor model 530 heater with the 536CXB President ZC Cast Front comes ready for installation as a zero

clearance unit into combustible type framing, without need for a separate zero clearance kit. The 530 installed

without the standard zero clearance stand-off spacers may also be installed into existing solid-fuel burning replaces

provided space and local codes permit.

Hearth Requirements

A 7/8” high plinth is supplied to raise the heater and ensure a base at the proper height for the cast front to sit on

regardless of oor nish height. If not using the plinth supplied, you MUST make allowance for oor nish and raise

(shim) the heater up so the bottom of the heater sits at the nished oor/hearth height, otherwise, the cast front will

not sit at the proper height.

Anon-combustible hearth is not required in front of this appliance.

Floor Requirements

The 530 heater is approved for installation directly on any combustible material other than soft ooring material

such as carpet or vinyl.

Mantel Requirements

The 536CXB President ZC Cast Front may be installed with a combustible mantel provided clearances are

maintained as indicated in the Dimensions and Clearances below and in the Framing diagrams on the following

pages. Be aware that although safe, some combustible materials and nishes at the listed clearances may, over

time, discolor, warp, or show cracks. Care should be taken when choosing materials—consult your replace dealer.

INSTALLATION WITH 530 ENGINE

FRAMING

The President ZC Front comes supplied

with a framing plate for zero clearance

applications. The framing plate is

painted black and may be left exposed

beyond the perimeter of the cast iron

front or may be covered with non-

combustible material if desired.

A non-combustible hearth is not

necessary in front of this appliance.

The appliance is approved to install

directly on wood sub-ooring.

Any framing construction must be

clear of stand-offs.

Be aware that the area of 7½” x

26¼” (19 cm x 67 cm) immediately

above the framing plate must be

constructed with non-combustible

materials as shown in gures.

•

non-combustible finish

and backing required

Tighten screws after wall finish

to pull brackets tight

Cast Front

Framing Plate

Cover brackets

Cover Framing Plate

up to holes

Wall Finish

(note: any material

covering framing plate

or within 7-1/2”at top

must be non-combust.

non-combustible finish

& backing required

Mount Brackets to Heater

Install Framing Plate

flush with framing or

butt drywall to plate

and run finish over plate

Raised plinth

not shown

Framing Plate

Header Location for

Rear Vent Installations

Brackets Screwed tight

to Plate

Wall Finish

Combustible or

non-combustible

Framing Plate Protudes

by desired wall finish

thickness

Bend Tabs out

for desired wall

finish thickness

Tab Detail

Cast Front

Covers Brackets

Non-Combust.

Mat’l only

Above

Framing Plate

Raised plinth

not shown

Framing plate exposed

Framing plate covered

Top of finished

hearth or floor

Wall Finish

26-1/4”

31-1/2”

to header &

wall finish

(includes

plinth -

reduce by

7/8”if not

using plinth)

7-1/2”

minimum

This part of wall

must be

non-combustible

(cement board or

similar)

Minimum 11”

(Allow extra for rear vent elbows)

Top of finished

hearth or floor

Wall Finish

Note: Header

is raised to

accomodate top

vent clearances

39”

to header

(includes

plinth;

reduce by

7/8”if not

using plinth)

31-1/2”

to header

(includes

plinth;

reduce by

7/8”if not

using plinth)

7-1/2” minimum

This part of

wall must be

non-combustible

(cement board

or similar)

Minimum 11” 26-1/4”

Rear vent framing

Top vent framing

INSTALLATION

Fit the top bafe under the top panel of the appliance

case. Secure with 2 thread forming screws.

Fit the stand-off spacers. The stand-off spacers for

these installations are supplied at. They are left and

right handed.

! Warning: Failure to install the stand-off spacers

may result in a re hazard.

Remove the 2 screws near each of the rear top

corners of the appliance and the 2 screws near

each side of the top back corners.

Bend the spacers as shown.

Screw the spacers to the rear of the appliance

using the screws just removed.

Bend the side wings of the spacers to align the 2

holes in each spacer with those in the appliance

sides. Secure the spacers using the screws just

removed.

Mount the framing plate to the appliance.

Secure the framing plate and brackets to the sides

of the appliance case with 4 thread cutting screws

supplied. Screw from the outside through the access

holes in the framing plate.

Note: There are alternate methods of nishing around

the framing plate—either leaving it exposed or

recessing it and covering it up with the wall nish. See

page 4.

4”

(102 mm)

total

insulation

Cut out insulation

for top vent installation

Pull forward to expose

width of 4”

Install the plinth and the rear base support below the rebox

(optional).

The purpose of the plinth is to allow the appliance to be placed

on a rough suboor, such as plywood, without regard for the

additional thickness of oor nishes as the appliance bottom

must otherwise be placed at the nished hearth height or the

front trims will not t properly on the appliance.

Detach the burner module from the appliance by removing

its 11 screws.

Fit the rear base support under the rear of the appliance

attaching it to the appliance back panel with 2 x ⅜” thread

cutting (pointed end) screws.

Fit the front plinth under the appliance front with 2 thread

forming screws.

Install the top insulation layer. For top vent outlet appliances,

cut out a circle at the center of the insulation layer for the vent

collar. Place the insulation layer on top of the appliance case

inboard of the stand-off spacers.

! Warning: Failure to install the insulation layer may cause

a re hazard and void warranty.

If the hooks have been shipped loose with the cast front,

x them to the front at its top corners. Hang the front on the

appliance.

CLEANING

It will be necessary to clean the glass periodically.

During startup, condensation, which is normal, forms

on the inside of the glass and causes dust, lint or other

particles to cling to the glass surface.

Initially, paint, while curing, may deposit a slight lm on

the glass. We therefore recommend that, during the rst

few weeks of use, the glass be cleaned 2 or 3 times with

non-abrasive common household cleaners and warm

water.

Ammonia based cleaners should not be used.

Subsequently the glass should be cleaned 2 or 3 times a

season depending on the circumstances.

Do not clean the glass while it is hot.

Dust can be brushed from the ceramic fuel effects and

rebox walls after removing the front unit and opening

the window.

Removing the front unit

Unhook the cast front. Lift it up by holding the decorative

grille. DO NOT lift by holding the top.

Opening the window

Always securely replace the window before

lighting.

The inside of the window can be cleaned by pulling

forward and rotating the 2 clamping bars at the top

corners of the window and swinging the window part way

down as shown.

! Be careful not to distort or damage the spring-

loaded bolts—don’t swing the window down more

than is necessary!

To completely remove the window, also unscrew the

2 spring-loaded bolts at the bottom of the window as

shown.

After retting the window, apply light hand pressure

against the window frame sides to bed-in the window

seal.

Dust can also be removed from the burner using a soft

brush after removing the ceramic fuel effects.

When cleaning, make sure that no particles are

brushed into the slots of the burner.

Always completely remove the window before

removing the ceramic fuel effects.

REPAIR PARTS LIST

#Description Number Alternate no. Qty

1 Front Unit 568979 040A519 1

2Door Hinge Bolt 568999 420K558 1

3Ashpan Door 568989 540K048AZ 1

4Washer 532529 100B810 1

5Magnet unit 569009 020A085 1

6Front Casting 568929 050A255AZ 1

7 Front Casting Hook RH 568949 330A923 1

8Front Casting Hook LH 568939 330A922 1

9Side Shield 568959 330A928 2

10 Top Casting 568969 550K065AZ 1

11 Top Bafe 569019 340B252AZ 1

12 Rear Base Support 569079 340B236 1

13 Plinth 569059 350K967 1

14 Framing Plate 4000469 4000469 1

15 Heater Mounting Bracket 4000489 4000489 2

16 ZC Stand-off LH 569039 340B235 1

17 ZC Stand-off RH 569029 340B234 1

18 Insulation Layer 569049 620B987 2

#536CXB

Devanture de fonte

President ZC

homologuée par la CSA pour utilisation

exclusive avec le foyer Valor 530

GUIDE D’INSTALLATION

Note: Ce kit doit être installé ou réparé par un installateur qualié, une agence de service certiée

ou un fournisseur de gaz. Ces instructions doivent être utilisées conjointement avec les

instructions d’installation du modèle de foyer Valor indiqué ci-dessus.

MISE EN GARDE: Si les instructions fournies dans le présent manuel ne sont pas suivies à

la lettre, un feu ou une explosion pourraient résulter et causer des dommages matériels, des

blessures ou la mort.

POUR INSTALLATION AVEC LE FOYER VALOR 530.

POUR LA CONFIGURATION ET L’ÉVACUATION DU FOYER VALOR

530, CONSULTEZ LE MANUEL D’INSTALLATION FOURNI AVEC LE

FOYER.

INSTALLATEUR : Laissez cette notice avec l’appareil.

CONSOMMATEUR : Conservez cette notice pour consultation ultérieure.

Conçue et fabriquée par / pour

Miles Industries Ltd.

190 – 2255 Dollarton Highway, North Vancouver, C.-B., CANADA V7H 3B1

Tél. : 604-984-3496 Téléc. : 604-984-0246

www.milesreplaces.com

Inhaltsverzeichnis

Sprachen:

Andere Valor Kamin im Innenbereich Handbücher

Valor

Valor STONEFIRE SF10BL Bedienungsanleitung

Valor

Valor 650JLN Bedienungsanleitung

Valor

Valor quantum BR644 VA Bedienungsanleitung

Valor

Valor Legend 739ILN Handbuch

Valor

Valor Heartbeat Oxysafe 426 Bedienungsanleitung

Valor

Valor LT1 2500KN Bedienungsanleitung

Valor

Valor DIMENSION ELECTRIC Series Bedienungsanleitung

Valor

Valor Wellington Bedienungsanleitung

Valor

Valor LINEAR SERIES Bedienungsanleitung

Valor

Valor 1800JN Betriebsanleitung

Valor

Valor H6 Series Montageanleitung

Valor

Valor 639 Montageanleitung

Valor

Valor 530XAN Montageanleitung

Valor

Valor Dream Fireslid 9500433 Montageanleitung

Valor

Valor LEGEND G4 785XN Montageanleitung

Valor

Valor Ultimate Turbochim BR517S Montageanleitung

Valor

Valor G3 739 Bedienungsanleitung

Valor

Valor 953 Gebrauchsanweisung

Valor

Valor H3 1000JN Planungshandbuch

Valor

Valor H5 1100MN Bedienungsanleitung

Valor

Valor LX Series Planungshandbuch

Valor

Valor DEC1 Handbuch

Valor

Valor Legend 937AN Bedienungsanleitung

Valor

Valor 961 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch