Valor Churchill LFE Bedienungsanleitung

3002206/02

OWNER’S GUIDE

THIS APPLIANCE IS FOR USE WITH NATURAL GAS (G20)

THIS APPLIANCE IS FOR USE IN THE UNITED KINGDOM (GB) AND THE

REPUBLIC OF IRELAND (IE) ONLY.

This guide is intended to help you care for your gas fire. Please read thoroughly before

using and keep for future reference

For Service Phone 0845 960 5040

Manufactured exclusively for British Gas & Scottish Gas by Valor Heating, Wood Lane,

Erdington, Birmingham B24 9QP

This guide to be left with the owner

Churchill LFE

(GC No. 32-032-30)

OUTSET RADIANT/CONVECTOR

LIVING FLAME EFFECT GAS FIRE

(Manufacturer ref. 3413)

OWNER’S GUIDE

Page 2

Safety First.

This fire is CE Approved and designed to meet the appropriate British Standards and

Safety Marks.

Quality and Excellence

This fire has been manufactured to the highest standards of quality and excellence and

has been manufactured under a BS EN ISO 9001 quality system accepted by the British

Standards Institute.

The Highest Standards

The manufacturer is a member of the Society of British Gas Industries, which works to

ensure high standards of safety, quality and performance.

Careful Installation

The manufacturer is a CORGI registered company. This gas fire must be

installed by a competent CORGI Registered Installer in accordance

with our Installer Guide and should not be fitted directly on to a

carpet or floor of combustible material.

Because our policy is one of constant development and improvement, details may vary

slightly from those given in this publication

OWNER’S GUIDE

Page 3

LIST OF CONTENTS

CUSTOMER CARE

This gas fire has been designed to meet the most stringent quality, performance and

safety requirements to provide our customers with many years’ trouble-free service.

Your owner guide aims to improve your understanding and appreciation of your gas fire

by providing simple and informative instructions to ensure that you benefit from the

excellent performance and features it has to offer.

SAFETY ..............................................................................................................................4

APPLIANCE DIMENSIONS............................................................................................6

OPERATING YOUR FIRE ..............................................................................................7

CLEANING ........................................................................................................................9

MAINTENANCE ............................................................................................................ 11

OWNER’S GUIDE

Page 4

Graph 1 Combustible shelf clearances

SAFETY

IF YOU SMELL GAS

DON’T SMOKE

EXTINGUISH ALL NAKED FLAMES

DON’T TURN ELECTRICAL SWITCHES ON OR OFF

TURN OFF THE GAS SUPPLY AT THE METER

OPEN DOORS AND WINDOWS TO GET RID OF THE GAS

IMMEDIATELY CALL THE GAS EMERGENCY SERVICE – SEE YOUR

LOCAL TELEPHONE DIRECTORY

•Have the fire installed by a competent person. In the United Kingdom, installation

must be in accordance with the latest edition of the Gas Safety (installation & use)

Regulations. In the Republic of Ireland, installation must be in accordance with all

national and local regulations in force.

•Have the chimney swept prior to installation if it was previously used for solid fuel.

•Have the fire installed in accordance with the installation instructions

•Provide a minimum clearance as shown in graph 1 above the top of the outer case to

any shelf made of wood or other combustible material.

OWNER’S GUIDE

Page 5

•Provide a suitable guard that complies with BS 6539 or 6778 for the protection of

young children, the elderly and the infirm. Such a guard is also recommended for the

protection of pet animals. (Although this fire conforms to all the applicable standards,

it is a heating appliance and certain parts of its surface will become hot.)

Note: The glass panel acts as a fireguard conforming to BS1945:1971 and satisfies the

Heating Appliance (Fireguard) (Safety) Regulations 1991.

•Wait three minutes before attempting to relight if the fire is switched off or the flames

are extinguished for any reason. (Your fire is fitted with a safety device which will

automatically shut off the gas supply to the fire if, for any reason, the flames go out.)

•Get advice about the suitability of any wall covering near your fire. Soft wall coverings

(e.g. embossed vinyl, etc.) which have a raised pattern are easily affected by heat. They

may, therefore, scorch or become discoloured when close to a heating appliance.

Please bear this in mind whenever you are considering redecorating.

•Provide a minimum side clearance as detailed in figure 1. Please bear this in mind if

ever you are considering altering the room.

DON’T

•Hang clothing, towels or any other fabrics over the fire.

•Fill in the space behind the case.

•Use the fire with a damaged coal piece or with the coal incorrectly positioned.

•Use the fire if the glass window is damaged.

•Allow any combustible material (e.g. Wallpaper, plastic tiling, wood panelling etc.) on

the fireplace wall below the shelf.

•Attempt to clean or service the fire until it has been switched off and allowed to cool

completely.

OWNER’S GUIDE

Page 6

APPLIANCE DIMENSIONS

Figure 1 Dimensions

OWNER’S GUIDE

Page 7

OPERATING YOUR FIRE

PLEASE NOTE

When operating your fire for the first time, some vapours may be given off which may

cause a slight odour and could possibly set off any smoke alarms in the immediate

vicinity. These vapours are quite normal with new appliances. They are totally harmless

and will disappear after a few hours use.

The Oxysafe flame sensing & flue blockage safety system.

For your safety, this appliance is fitted with a flue blockage safety device which will shut

down the appliance in the event of abnormal flue conditions. This device is NOT a

substitute for an independently mounted Carbon Monoxide detector.

The device will also automatically shut off the gas supply to the fire if the pilot flame

goes out due to lack of oxygen or for any other reason.

If this device starts to repeatedly shut off the gas, get expert advice.

This device incorporates a probe which senses that the heat from the pilot flame is

correct. If this probe is cool, the device will prevent any gas flow unless the control knob

is held in at the ignition position.

If, for any reason, the flames go out when the fire is hot or if the fire is turned off when

hot, always wait at least three minutes before attempting to relight.

To light the fire

The control is shown in Figure 2.

•Depress the control knob and turn partially to

the 1/IGN position until you feel some

resistance.

•Keep the knob depressed at this position for a

few seconds to allow gas to flow to the burner.

•While keeping the knob depressed, turn to the

1/IGN position. While turning, a spark should

light the pilot.

•Keep the knob depressed at the 1/IGN position

for a further 10 seconds then release it. The

centre section of the coal will be alight at this

position.

•Depress the control knob slightly and turn it to

your desired burner setting.

•The control knob should be depressed slightly

before turning whenever you are changing the burner setting.

Figure 2 The Control

OWNER’S GUIDE

Page 8

Figure 3 Lighting with a taper

•The burner settings are;

1/IGN...........Centre section on low. Outer sections off.

2....................Centre section fully on. Outer sections off.

3....................Centre section fully on. Outer sections on low.

4....................Centre section fully on. Outer sections fully on.

•We recommend that the fire is set at position 4 for the first 10 minutes after lighting to

warm up the chimney and so obtain full efficiency quickly.

•If operating the appliance for long periods it is beneficial occasionally to change the

settings. This will also help to remove any carbon deposits that may form during

operation.

Note: If the fire goes out while setting the control, repeat the full lighting procedure. If

the fire repeatedly goes out, have the fire serviced.

To turn the fire off

•Partially depress the control knob and turn clockwise to OFF. Release the knob.

•Wait at least 3 minutes after turning the fire off before relighting.

Lighting with a taper

In the unlikely event of failure of the ignition

spark, the pilot can be lit with a taper or long

spill after the window surround has been

removed. Removal of the surround is

described in the “Cleaning Window Glass”

chapter on the next page.

Light the pilot by inserting the taper or spill

below the centre of the window while the

control is kept depressed at the 1/IGN

position. See figure 3.

When the pilot has lit follow the rest of the

instructions in the instructions headed “To

light the fire”.

OWNER’S GUIDE

Page 9

Figure 5. Window removal

Figure 4. Window surround removal

CLEANING

To maintain the high performance and

quality finish of your gas fire, please follow

these guidelines:

•Before attempting to clean the fire,

please remember to turn off the fire and

wait for the appliance to cool. The fire

will retain heat for some time before

cleaning can begin.

•If any pieces of debris are found in the

fire box, have the chimney inspected

before further use.

Metal Parts

•Clean the metal parts with a slightly

damp cloth and then dry.

•Do not use abrasive cleaners as these will

scratch the fire surface.

Window Glass

•Remove any stains on the window with a

non-abrasive cleaner such as a ceramic hob

cleaner. Do not use abrasive cleaners.

•The fire has been designed to so that you can

remove the window without having to call in

a service engineer. This allows you to clean

the inside of the window.

To remove the window:

1. Detach the window surround by sliding it upwards and then swinging the bottom

forwards. Lift and store carefully. See figure 4.

2. Remove the window unit by turning the screws each side of the window frame ¼ turn

anticlockwise. A screwdriver is provided with your fire for turning the screws. Lift

the window unit clear. See figure 5.

OWNER’S GUIDE

Page 10

Figure 7. Coal bed location

Figure 6. Window surround fitting

3. After cleaning, replace and

secure the window unit to the

firebox by turning the two screws

1/4turn clockwise with the

screwdriver.

Refit the window surround by

sliding the surround upwards to

locate its upper tabs in the slots

underneath the outer case hood.

Push the bottom of the surround

fully against the case cross panel.

Drop the surround down so that

the two screw heads at the back of

the surround locate in the

keyholes in the cross panel. See

figure 6.

Ceramic Coal

•This product uses a fuel effect piece containing

Refractory Ceramic Fibres (RCF), which are man-

made vitreous silicate fibres. Excessive exposure to

this material may cause temporary irritation to eyes,

skin and respiratory tract. Consequently, it makes

sense to take care when handling this article to

ensure that the release of dust is kept to a minimum.

•Although light coatings of soot are usually burnt

off during normal use, the coal may benefit from

occasional cleaning.

•Should any soot accumulation become excessive,

the fuel effect piece should be removed from the

fire for cleaning. Cleaning should be carried out in

a well ventilated area or in the open air by gently brushing with the pieces held away

from your face so that you avoid inhaling the dust. We do not recommend the use of a

normal domestic vacuum cleaner which may blow dust back into the air.

•The coal can be lifted out of the fire box when the window surround and glass have

been removed as described on page 8.

•When replacing the coal, make sure that it rests on the ledges at the sides of the firebox

and that its back face is touching the horizontal rib at the back of the firebox. See

figure7.

•Replace the window and surround after cleaning.

Inhaltsverzeichnis

Andere Valor Kamin im Innenbereich Handbücher

Valor

Valor L1 Series Betriebsanleitung

Valor

Valor BELVOIR DIMENSION Bedienungsanleitung

Valor

Valor Black Beauty Radiant Montageanleitung

Valor

Valor LEGEND G4 780IN (NG) Handbuch

Valor

Valor ALPHA 647 Bedienungsanleitung

Valor

Valor 1337MFP Bedienungsanleitung

Valor

Valor Valorflame 450 Benutzerhandbuch

Valor

Valor H5 1100MN Planungshandbuch

Valor

Valor 500FS Gebrauchsanweisung

Valor

Valor 1700IN Betriebsanleitung

Valor

Valor LEGEND 739JLN Logs Betriebsanleitung

Valor

Valor LEGEND G4 785ILN (NG) Montageanleitung

Valor

Valor 495 Bedienungsanleitung

Valor

Valor LX1 Series Bedienungsanleitung

Valor

Valor G4 780MNGK Bedienungsanleitung

Valor

Valor Portrait 530ILN/ILP Betriebsanleitung

Valor

Valor 639 Montageanleitung

Valor

Valor Firelite OXYSAFE 2 Bedienungsanleitung

Valor

Valor Wonderfire BR419 Bedienungsanleitung

Valor

Valor RetroFire RF24DN Montageanleitung

Valor

Valor BR419 VA Bedienungsanleitung

Valor

Valor Heartbeat Oxysafe 426 Versionshinweis

Valor

Valor Legend 936XN Montageanleitung

Valor

Valor HORIZON 535 Bedienungsanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch