Valor PORTRAIT 575LFK Bedienungsanleitung

4002695-06

575LFK Lift Freestanding Kit

Installation Instructions

CSA approved for use with Valor Models 530I Heaters ONLY

Includes installation instructions for 576LCP and 578LF kits

To complete the installation

of this kit you need the

following items:

• 530I Portrait Engine

• 575LFK Lift Freestanding

Kit

• 578LF Lift Front

• 576LCP Lower Cover

Panel (optional)

Notes: This kit must be installed or serviced by a qualiﬁed

installer, service agency or gas supplier. These instructions are to

be used in conjunction with the main installation instructions

for the above listed heater models.

The application of this kit does not affect the venting

capabilities or method of preparation of the 530 heater as

described in the 530 heater installation manual.

INSTALLER

Leave this manual

with the appliance.

CONSUMER

Retain this manual

for future reference.

576LCP—

Lower Cover

Panel

530I—

Portrait Engine

578LF—Lift Front

575LFK—Lift Freestanding Kit

(back panel comes with 578 kit)

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

WARNING

A barrier designed to reduce the risk of burns from the hot viewing

glass is provided with this appliance and shall be installed

for the protection of children and other at-risk individuals.

PORTRAIT

Overview (530I, 575LFK, 576LCP and 578LF sold separately)

Basic Installation Sequence

• Assemble sides of casing, bottom and top front

brackets.

• Assemble bottom brackets to heater.

• Fit heater in casing and bolt in place.

• Assemble rear brackets to heater and ﬁx to casing.

• Gas ﬁt and vent heater.

• Hook the rear panel, the top panel and inﬁll panel.

• Install ﬁrebox grille and complete installation of

heater as per heater installation instructions.

• Install bracket and place lower cover panel if used.

• Hook window frame cover and front.

Tips

• Wear gloves or ensure to manipulate the cast

iron/concrete pieces with clean hands to avoid

any stain.

• Remove the 530 window and all items inside the

appliance before installing to lighten it.

• In steps 4, 5 and 7 in the following instruc-

tions, assemble the parts loosely, just enough

for them to hold together. This will allow you

to ﬁt all the parts more easily. Then, in step

10, after all the parts are ﬁtted together and

adjusted, tighten all the screws.

Kits Contents

575LFK Lift Freestanding Kit (required)

• Casing left side

• Casing right side

• Top panel

• Top inﬁll panel

• Convection bafﬂe

• Front hanging bracket

• Rear hanging brackets (2)

• Bottom support brackets (2)

• Engine brackets (2)

• Hardware

576LCP Lower Cover Panel (optional)

• Lower cover panel

• Support bracket

• Hardware

578LF Lift Front (required)

• Front trim with screen

• Window frame cover

• Back panel

• Firebox grille

Bottom support

brackets

Engine

brackets

Firebox grille

Convection

bafﬂe

Front

hanging

bracket

Top panel

Top inﬁll panel

Rear

hanging

brackets

Casing left

hand side

Casing right

hand side

Back panel

Window frame cover

Front trim

Lower cover panel

Support bracket

37-15/16”(964 mm)

29-1/8”(739.7 mm)

23-11/16”(601.6 mm) 13-5/16”

(338.5 mm)

24-5/8”(625 mm)

Ceiling

576LCP

optional

panel

36”

(914 mm)

min.

See table

14-5/8”(371.5 mm)

3”

(76.2 mm)

min.

4-15/16”

(109.5 mm)

Zero

clearance

Gas line access

point through

casing

Gas line access

point 8-1/2”(216 mm)

Gas line connection

point 3/8”NPT FEMALE

at valve

Zero clearance

Sidewall

Mantel

Minimum 53-7/8” (1368.4 mm)

Zero clearance

Minimum

17-1/4”

(438.1 mm)

Minimum 38” (967.3 mm)

Minimum

12-1/4”

(311.5 mm)

90°

Front View Top ViewRight Side View

Corner Dimensions

Dimensions & Clearances to Combustibles

Mantel

Depth ‘A’ 0–15”

(0–381 mm) 16”

(406 mm) 18”

(457 mm) 20”

(508 mm) 22”

(559 mm)

Mantel

Height ‘B’ 2”

(51 mm) 3”

(76 mm) 5”

(127 mm) 7”

(178 mm) 9”

(229 mm)

Casting Tolerances

Due to the nature of cast iron and concrete, dimen-

sional consistency may vary from one unit to the

next and some variation in surface ﬁnish and ﬂat-

ness is to be expected. We have done our best to

control and make allowance for this; however some

variation is inevitable.

Floor Requirements

The 530 heater is approved for installation directly

on any combustible material other than soft ﬂooring

material such as carpet or vinyl.

Mobile Home Floor Fixing

The Lift FS must be ﬁxed to the ﬂoor through the

ﬂoor when used in a mobile home.

Mantel Requirements

The Lift FS may be installed with a combustible

mantel provided clearances are maintained as

indicated below. Be aware that although safe,

some combustible materials and ﬁnishes at the

listed clearances may, over time, discolor, warp,

or show cracks. Care should be taken when

choosing materials—consult your ﬁreplace dealer.

Combustible Mantel Clearances

Tip

In steps 4, 5 and 7 in the following instructions,

assemble the parts loosely, just enough for them

to hold together. This will allow you to ﬁt all the

parts more easily. Then, in step 10, after all the

parts are ﬁtted together and adjusted, tighten all

the screws.

Installation

1. Identify the front and rear of one cast iron/concrete

side panel. The front of the panel has a protruding

piece at the top.

2. Install the bottom support brackets. Loosen off the

bottom screws and insert the screw heads in the

keyholes of the brackets as shown. Make sure the

brackets are oriented properly. Tighten the screws.

front

Rear view

outer edge with

two holes

Bottom brackets orientation

inner edge with

downward lip Rear view

Rear view

Front view, left side

Lip goes

to the front

Top

Bottom

Front view

3. On the other side panel, loosen off the bottom

screws. Place the ﬁrst panel at the desired location.

Place the second panel as indicated and attach

the bottom support brackets sliding them over the

screw heads of the panel. Tighten the screws.

4. Loosely ﬁx the front hanging bracket to the side

panels with one black machine screw on each side.

5. Fix the engine brackets to the bottom of the

appliance with one machine screw on each side as

indicated. Either bracket can be used on either side

of the appliance.

6. Slide the appliance into the casing from the top.

Loosely ﬁx the appliance to the casing with a nut

and bolt on each side at the front and one nut and

bolt at the rear left-hand corner.

7. Remove two screws on each side of the back panel

of the appliance case. Secure the top rear support

brackets to the appliance case using the screws

previously removed. Loosely ﬁx the appliance to the

casing with one self-tapping screw per side.

8. Slide the convection bafﬂe under the top panel of

the appliance case. Fix the convection bafﬂe using

two machine screws provided.

9. Prepare the heater for venting—top or rear outlet as

necessary. Refer to the heater installation manual.

Please note that depending on the vent collar

location, the casing top and/or back panel must

be ﬁtted over the vent collar. Do not install the

vent pipes before you install these panels.

10. Adjust the position of the heater in the casing as

necessary. Fit the top panel and tighten all the

screws loosely ﬁtted in steps 4, 6 and 7. Ensure

the heater is centered and leveled with the casing.

Remove the top panel.

11. Hook the rear panel to the rear hanging brackets.

Cut out the knock-out ﬁrst if rear venting. The rear

panel is provided with the 578 kit.

12. Adjust the stove to its ﬁnal position.

13. If necessary, level the stove using the leveling bolts

inside the front legs of the casing.

Grille inserted

parallel to

ﬁrebox edge

14. Fit the top panel of the casing. If necessary, level

the top panel using the leveling screws at the top

rear corners of the casing. Fit the inﬁll panel if rear

venting.

15. Install and connect the venting. See the heater

installation manual for more information.

16. Remove the window. Connect the gas. See the

heater installation manual for more information.

17. 555CFK Circulating Fan Kit. If you are installing a

fan kit, we recommend that you proceed now.

18. BEFORE you install the ceramic panels, install

the ﬁrebox top grille provided with the 578 kit as

follows:

LOGS & ROCKS VERSIONS ONLY. Grille cannot

be used with coal fuelbed version. Install the grille

panel inside the appliance:

a. Insert the grille in the ﬁrebox by aligning one

of its side edge to the edge of the ﬁrebox as

indicated.

b. Raise the grille

up to cover the

top ﬁrebox ports

and hold with

one hand.

Note: The port

cover strip

supplied with

the heater is not

required.

Window frame

cover—rear view

Top

c. Place the rear

brick wall. It

should support

the grille. If not,

keep holding it

while you place

the side brick

walls. Refer to

the ﬁreplace

installation

manual for more

information on installing the brick walls.

19. Finish the installation of the heater including all

the checks necessary for function. Reinstall the

window.

20. Hook the window trim cover provided with the 578

kit on the top edge of the window frame.

21. If the 576 optional panel will be used, install it now.

a. Fix its support bracket to the bottom front

bracket of the casing using two screws.

b. Slide in the cover panel at a angle to insert it

between the casing’s legs. Center it and lean it

against its support.

22. Hook the 578 front trim to the casing top front

bracket as shown.

Maintenance

Dust down the surface regularly with a soft brush and

occasionally follow up with a wipe over with a wet cloth.

A sealer has been applied to the surface, no cleaning

agents nor polishes should be used. In case of an

accidental spill, soak up the liquid IMMEDIATELY with

a dry cloth and follow up with a wipe down with a wet

cloth.

The front steel trim can be cleaned with Windex. To

clean the barrier screen, use a soft brush.

If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this

appliance.

To clean the stove glass window, refer to the owner’s

manual supplied with the appliance. DO NOT clean

with ammonia.

WARNING

DO NOT TOUCH THE BARRIER SCREEN OR

STOVE WHILE THEY ARE HOT!

Let the stove

cool first before cleaning it.

FOR SAFETY PURPOSE, ensure the

barrier screen is re-installed on the

stove front after maintenance.

Repair Parts List

575LFK—Lift Freestanding Kit

Code Description Part Numbers

1 Top inﬁll panel 4002060

2 Top panel 4002059

3 Casing left side assembly 4002993

4 Casing right side assembly 4002992

5 Left side rear hanging bracket 4002977

6 Right side rear hanging bracket 4002978

7 Convection bafﬂe 4002075BY

8 Front hanging bracket 4002964AZ

9 Catch (2) 4002688

10 Engine brackets (2) 4002678AZ

11 Bottom brackets (2) 4002677AZ

M6 x 18 top leveling screws (2) 4003031

Bottom leveling screws (2) 4003021

Hardware Kit 4003030

578LFCH—Lift Front Charcoal

Code Description Part Numbers

1 Back panel 4002071AZ

2 Firebox grille 4002101EB

3 Window frame cover 4002279BY

4 Heat duct 4002081BY

5 LS lead-in 4002693AZ

6 RS lead-in 4002692AZ

7 Lower lead-in 4002687AZ

8 Barrier screen 4003429

9 Steel trim charcoal 4002691CH

576LCP—Lower Cover Panel

Code Description Part Numbers

1 Support Bracket 4002990

2 Fluted Panel 4002857

Screws 8 x 3/8 (2) 100A757

Designed and Manufactured by / for

Miles Industries Ltd.

190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1

Tel. 604-984-3496 Fax 604-984-0246

www.valorﬁreplaces.com

Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication.

575LFK 576LCP

578LFCH

PORTRAIT

Concept (530I, 575LFK, 576LCP et 578LF sont vendus séparément)

LE PREMIER

FOYER À GAZ RADIANT

Poêle Lift 575LFK

Directives d’installation

Homologué par la ACN (CSA) pour utilisation avec le foyer Valor 530I SEULEMENT

Inclut les directives d’installation pour les ktis 576LCP et 578LF

Les articles suivants sont requis pour

compléter l’installation de ce kit :

• Foyer Portrait 530I

• Poêle Lift 575LFK

• Devanture Lift 578LF

• Panneau du bas 576LCP (facultatif)

Notes : Ce kit doit être installé ou réparé par un installateur qualiﬁé, une agence de service certiﬁée

ou un fournisseur de gaz. Ces instructions doivent être utilisées conjointment avec les instructions

d’installation du modèle de foyer Valor indiqué ci-dessus.

L’application de ce kit n’affecte pas l’évacuation ou les méthodes de préparation de l’appareil tels que

décrits dans le guide d’installation du foyer 530I as described in the 530 heater installation manual.

575LFK—Lift Freestanding Kit

(back panel comes with 578 kit)

Devanture Lift 578LF

Foyer Portrait 530I

576LCP—

Panneau

du bas

(facultatif)

INSTALLATEUR : Laissez cette notice avec l’appareil.

CONSOMMATEUR : Conservez cette notice pour consultation ultérieure.

UNE SURFACE VITRÉE CHAUDE PEUT

CAUSER DES BRÛLURES.

LAISSEZ REFROIDIR LA SURFACE VITRÉE

AVANT D’Y TOUCHER.

NE PERMETTEZ JAMAIS À UN ENFANT

DE TOUCHER LA SURFACE VITRÉE.

AVERTISSEMENT

Une grille de protection conçue pour réduire les risques de brûlures sur la vitre

chaude de la fenêtre est fournie avec cet appareil et doit être installée pour la

protection des enfants et autres individus à risques.

Conseils

• Portez des gants ou assurez-vous de manipuler

les pièces de béton avec les mains propres pour

éviter de les tacher.

• Enlevez la fenêtre du foyer de même que tous

les morceaux emballés dans sa cavité avant de

l’installer aﬁn de l’alléger.

• Aux étapes 4, 5 et 7 de l’installation,

assemblez les pièces sans serrer les vis

complètement, les serrant juste assez pour

que les pièces tiennent ensemble. Ceci

facilitera le montage. Ensuite, à l’étape

10, après avoir fait tous les ajustements

nécessaires pour que tout soit d’aplomb,

serrez les vis pour solidiﬁer le montage.

Étapes d’installation

• Assemblez les côtés du poêle avec les supports de

montage du bas et la barre de suspension avant.

• Assemblez les supports de montage du foyer.

• Insérez le foyer dans le casier du poêle.

• Assemblez les supports de suspension à l’arrière du

foyer et ﬁxez-les aux côtés du casier.

• Installez l’alimentation de gaz et montez le système

d’évacuation.

• Accrochez le panneau arrière et placez le panneau

du dessus et le couvre-évent.

• Installez la grille de boîte de foyer et complétez

l’installation selon les directives fournies avec le

foyer.

• S’il y a lieu, installez le support du panneau du bas

et le panneau.

• Accrochez la bordure de fenêtre et la devanture.

Contenu des kits

Poêle Lift 575LFK (requis)

• Côté gauche du poêle

• Côté droit du poêle

• Panneau du dessus

• Couvre-évent

• Déﬂecteur de convection

• Barre de suspension avant

• Support de suspension arrière (2)

• Supports de montage du bas (2)

• Supports du foyer (2)

• Quincaillerie

Panneau du bas 576LCP (facultatif)

• Panneau

• Support

• Quincaillerie

Devanture Lift 578LF (requise)

• Devanture avec grille de protection

• Bordure de fenêtre

• Panneau arrière

• Grille de boîte de foyer

Supports de

montage du bas

Supports

du foyer

Grille de boîte

de foyer

Déﬂecteur

convection

Barre de

suspension

avant

Panneau du dessus

Couvre-évent

Supports de

suspension

arrière

Côté

gauche

du poêle

Côté

droit du

poêle

Panneau

arrière

Bordure de fenêtre

Devanture 578LF

Panneau

Support

Inhaltsverzeichnis

Sprachen:

Andere Valor Kamin im Innenbereich Handbücher

Valor

Valor Legend G3.5 700JN Bedienungsanleitung

Valor

Valor 1440 Bedienungsanleitung

Valor

Valor Heartbeat OXYSAFE 2 Bedienungsanleitung

Valor

Valor 2100SFK Bedienungsanleitung

Valor

Valor HORIZON 534JN Betriebsanleitung

Valor

Valor H3 1000JN Planungshandbuch

Valor

Valor 961 Bedienungsanleitung

Valor

Valor Black Beauty Radiant Montageanleitung

Valor

Valor 347 Helmsley Bedienungsanleitung

Valor

Valor 780MN Bedienungsanleitung

Valor

Valor Legend G4 Series Betriebsanleitung

Valor

Valor 530SAN Montageanleitung

Valor

Valor 762 Gebrauchsanweisung

Valor

Valor L2 SERIES Betriebsanleitung

Valor

Valor LEGEND G4 780JN (NG) Montageanleitung

Valor

Valor HORIZON 613CCB Bedienungsanleitung

Valor

Valor AutoFire G4 Bedienungsanleitung

Valor

Valor Heartbeat Oxysafe 2 339 Gebrauchsanweisung

Valor

Valor Inspire 600FS Gebrauchsanweisung

Valor

Valor 1100JN Betriebsanleitung

Valor

Valor LEX2 Bedienungsanleitung

Valor

Valor HORIZON 534JN Bedienungsanleitung

Valor

Valor BR622 Bedienungsanleitung

Valor

Valor COSYFLAME TURBOCHIM 528 Montageanleitung

Beliebte Kamin im Innenbereich Handbücher anderer Marken

Brigantia

Brigantia 35-DVRS31N-2 Betriebsanleitung

Nordpeis

Nordpeis Bergen Bedienungsanleitung

Superior

Superior BCT2536TMN Bedienungsanleitung

Quadra-Fire

Quadra-Fire 5100I-GD-B Bedienungsanleitung

Renaissance

Renaissance RUMFORD 1000 Bedienungsanleitung

Lacunza

Lacunza IV-800 Bedienungsanleitung

Baxi

Baxi 940 Gebrauchsanweisung

Dru

Dru Maestro 60/2 Tall RCH Bedienungsanleitung

Diamond Fireglass

Diamond Fireglass SS-O22 Bedienungsanleitung

HearthStone

HearthStone Windsor Bay 8830 Programmierhandbuch

Napoleon

Napoleon ASCENT B42 Bedienungsanleitung

Enviro

Enviro E33GI Bedienungsanleitung

Smeg

Smeg L30 FABE Montageanleitung

KEDDY

KEDDY K700 Bedienungsanleitung

Godin

Godin 3451 Bedienungsanleitung

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Bedienungsanleitung

Desa

Desa CCFPDFT Bedienungsanleitung

Miles Industries

Miles Industries Vogue 1300IRN Handbuch