Valor MADRONA MFCS01 Bedienungsanleitung

4003648-06

MFCS01 or MFCS02

Madrona Traditional Stove Casting -

Arched front

MF28—Madrona Engine

(sold separately)

MF28—Madrona Engine

(sold separately)

MFCS01 or MFCS02

Madrona Traditional Stove Casting -

Square front

Note: This kit must be

installed or serviced by a

qualified installer, service

agency or gas supplier.

These instructions are to be

used in conjunction with the

main installation instructions

for the above listed heater

model.

Madrona Traditional Stove Casing

MFCS01 (black) or MFCS02 (Majolica brown)

Approved for use with Valor heater models MF28 ONLY

HOT GLASS WILL

CAUSE BURNS.

DO NOT TOUCH GLASS

UNTIL COOLED.

NEVER ALLOW CHILDREN

TO TOUCH GLASS.

DANGER

A barrier designed to reduce the risk of burns from the hot

viewing glass is provided with this appliance and must be

installed for the protection of children and other at-risk

individuals.

INSTALLER: Leave this

manual with the appliance.

CONSUMER: Retain this

manual for future reference.

INSTALLATION MANUAL

Madrona

To complete the installation of this kit you need:

• MF28 Madrona Engine + one of the following Casing:

• Black Arched model: MFCS01-1 + MFCS01-2

• Black Square model: MFCS01-1 + MFCS01-3

• Majolica Arched model: MFCS02-1 + MFCS02-2

• Majolica Square model: MFCS02-1 + MFCS02-3

Overview

Kits Contents

BLACK STOVE:

Arched version MFCS01-1 + MFCS01-2

Square version MFCS01-1 + MFCS01-3

MFCS01-1 - black

• Infill plate

• Top panel

• Legs (4)

• RH side panel

• LH side panel

• Hardware pack

MFCS01-2 - black

• Base panel

• Arched front panel

• Arched barrier screen

• Fret traditional

MFCS01-3 - black

• Base panel

• Square front panel with

square barrier screen

MAJOLICA BROWN STOVE:

Arched version MFCS02-1 + MFCS02-2

Square version MFCS02-1 + MFCS02-3

MFCS02-1 - majolica

• Infill plate

• Top panel

• Legs (4)

• RH side panel

• LH side panel

• Hardware pack

MFCS02-2 - majolica

• Base panel

• Arched front panel

• Arched barrier screen

• Fret traditional

MFCS02-3 - majolica

• Base panel

• Square front panel with

square barrier screen

MFCS01-1 ou MFCS02-1

MFCS01-2 ou MFCS02-2

MFCS01-3 ou MFCS02-3 Hooks

Square front

Fret

Top panel

Infill plate

Base

Legs

RH Side panel

LH Side panel

Arched front

Barrier screen

Mantel

23”

(584 mm)

7-1/2”

(191 mm)

25-1/8”(638 mm)

27-1/2”(699 mm) 14”

(356 mm)

17-7/8”

(454 mm)

Ø 6-5/8”

venting

Supplied with

top vent; field

convertible to

rear vent

Centre of vent

28-1/2 ”(724 mm)

xGas inlet position

3/8” fem. NPT

2”

(52 mm)

minimum

Gas line connection point

3/8”NPT FEMALE at valve

Sidewall

17-7/8”(454 mm)

4”

(102 mm)

2” (52 mm)

minimum

Ø 6-5/8”

venting

Suggested gas line

access point through wall.

Route to avoid optional fan.

Pipe supplied with

engine (see engine

manual p. 18)

Mantel / shelf clearances

Mantel

Depth ‘A’

0–1

[0–26]

2–5

[51–127]

6–18

[152–457]

19–24

[483–610]

Mantel

Height ‘B’

[864]

[914]

[965]

[1067]

Corner clearances

Min. 2”

between

combustible

wall and

stove

Min. 2” between

combustible wall

and stove

32-1/2” minimum

42” minimum

26” maximum

Alcove clearances

inches [mm]

Dimensions & Clearances

For installation purposes, diagrams

represented by the arched front

Tip

• Remove the MF28 window and all items inside the

appliance before installing to lighten it.

Installation

Unpack the appliance and stove casing

The Madrona engine is supplied separately from the

stove casings. The Traditional stove—MFCS01 (black)

or MFCS02 (majolica brown)—and the Contemporary

stove MFCS04 are each supplied in two cartons. You

must have in hand the stove casing before starting the

assembly of the appliance.

Unpack the carton carefully. We strongly recommend

that you leave the engine sitting on the packaging

base in which it came to avoid damaging the control

valve, wires and pipes already attached to the engine

until it is ready to insert in the stove casing.

Some parts are packed in the cardboard sleeve around

the engine; make sure you take them all out of the

packaging. Make sure you have all the components

including the stove casing components before you start

the installation.

Caution

LEAVE THE ENGINE ON ITS PACKAGING BASE to

avoid damage to the control valve, wires and

pipes until ready to insert into stove casing.

Casting Tolerances

Due to the nature of cast iron and concrete, dimen-

sional consistency may vary from one unit to the next

and some variation in surface finish and flat-ness is

to be expected. We have done our best to control

and make allowance for this; however some variation

is inevitable.

Floor Requirements

The Madrona heater is approved for installation

directly on any combustible material other than soft

flooring material such as carpet or vinyl.

Mobile Home Floor Fixing

The Madrona stove must be fixed to the floor

through the floor when used in a mobile home.

Mantel Requirements

The Madrona stove may be installed with a

combustible mantel provided clearances are

maintained as indicated above. Be aware that

although safe, some combustible materials and

finishes at the listed clearances may, over time,

discolor, warp, or show cracks. Care should be taken

when choosing materials—consult your fireplace

dealer.





%ROWV

Appliance’s foot print

Detail

Casting Base

1. Rough-in the gas line and electrical wiring for a fan

(if any).

2. Decide where the stove should be positioned to

avoid moving it once all the casting pieces are

attached together.

3. Place the casting base upside down. Unscrew the

bolts to insert the legs.

4. Slide each leg under the head of its bolt.

5. Tighten the bolts securely with a wrench.

6. Fix the casting base to the floor or hearth using bolts

(not supplied) through the casting feet—see the

bolting pattern below.

(Required for mobile homes only).

7. Flip the base up. Place the engine on the base at

its approximate final position—see detail below.

Center the engine using the holes at front of the

base as guidelines.

Detail

Casting Side Panels

1. On the casting side panels, release the top and

bottom screws.

2. Drop a hinge pin on the back corner of base and

drop the side panel on the pin.

3. Rotate the panel towards the engine.

4. Repeat with the other casting side panel.

Fixing Casting Side Panels & Engine

1. Adjust the position of the engine to locate the top

and bottom screws of the side panels into the

slots of the engine’s side bracket. Tighten the top

and bottom screws.

2. Adjust the engine as required and fix it to the casting

base at bottom of its side brackets with the nuts

and bolts provided.

Top Spar

1. Position the top spar on the side brackets located

between the engine and the cast sides.

2. Secure the spar with two 3/8” pre-assembled screws

provided.

Complete engine installation

Refer to the engine installation manual for the following

steps.

1. Reposition the lighting instructions plate, remote

control receiver and connect gas line to the inlet

pipe.

2. Install the fan, if used, and convert the top outlet to

a rear outlet or co-linear outlet if necessary.

3. Install venting system.

4. Connect the gas and install the logs.

5. Refit the window and the hot glass warning plate.

6. Set up the remote control and check operation.

Front Installation

Hook the cast front

to the side brackets

located between the

engine and the cast

sides.

Cast front

Hook

Details Engine

Side bracket

Top Casting

Place the top casting piece on the top of the stove

ensuring the rear edge is flush with the rear edge of the

cast side panels. Fill in the vent space with the infill plate

if using a rear vent. To level the top casting, unscrew the

levelling bolts on the top rear of each casting side panel

as appropriate.

Removeable Fret (Arched Front only)

To access the gas valve and the remote control receiver,

the fret can be removed without removing the front

casting. Once the stove has cooled down and with

extra care not to hit the glass of the window, simply

slide up the fret out of its brackets, angle it up and

remove it. To put it back in place, proceed in the reverse

order.

Barrier Screen (Arched Front only)

Install the barrier screen to the front of the Madrona

stove.

1. Insert the top clip in the top of the opening of the

cast front.

2. Push the sides of the screen against the front so the

side clips hook to the front.

Maintenance

Cast iron stove body

The matte cast body (MFCS01) can be cleaned with

a soft brush. The enamel cast body (MFCS02) can be

cleaned with a damp soft lint-free cloth.

Barrier screen

Remove the barrier screen by pulling the top first then

the bottom. Dust down using a brush.

If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this

appliance.

Window and fireplace

See the Owner’s Information section in the Madrona

MF28 fireplace Installation and Owner’s Manual for

instructions on cleaning the window and fuel bed.

Hooks (2)

Fret Mounting

Brackets (2)

WARNING

DO NOT TOUCH THE BARRIER SCREEN OR

STOVE WHILE THEY ARE HOT! Let the stove

cool first before maintenance.

FOR YOUR SAFETY, ensure the barrier

screen is re-installed on the stove front

after maintenance, before use.

Repair Parts List

Designed and Manufactured by / for Miles Industries Ltd.

190 – 2255 Dollarton Highway, North Vancouver, B.C., CANADA V7H 3B1

Tel. 604-984-3496 Fax 604-984-0246

www.valorfireplaces.com

Because our policy is one of constant development and improvement, details may vary slightly from those given in this publication.

Description Part Numbers

Black Majolica

1 Base 4000926AZ 4000926MJ

2 Top Panel 4000928AZ 4000928MJ

3 Legs (4) 4000929AZ 4000929MJ

4 RH Side Panel 4000930AZ 4000930MJ

5 Front, Arched 4000934AZ 4000934MJ

6 Fret 4000935AZ 4000935MJ

7 LH Side Panel 4000931AZ 4000931MJ

8Inﬁll Plate 4000927AZ 4000927MJ

9Hooks(2) 4000990

with 4000883

4000990

with 4000883

10 Barrier Screen, Arched 4003311 4003311

11 Front, Square 4004911A Z 4004911MJ

12 Barrier Screen, Square 4004796 4004796

Quincaillerie 4000883 4000883

Note : Ce kit doit être

installé ou réparé par un

installateur qualifié, une

agence de service certifiée

ou un fournisseur de gaz.

Ces instructions doivent être

utilisées conjointement avec

les instructions d’installation

du modèle de foyer Valor

indiqué ci-dessus.

VITRE CHAUDE - RISQUE

DE BRÛLURES.

NE TOUCHEZ PAS UNE

VITRE NON REFROIDIE.

NE LAISSEZ JAMAIS UN

ENFANT TOUCHER LA VITRE.

L’écran pare-étincelles fourni avec ce foyer réduit le risque

de brûlure en cas de contact accidentel avec la vitre chaude

et doit être installé pour la protection des enfants et des

personnes à risques.

DANGER

!INSTALLATEUR : Laissez cette

notice avec l’appareil.

CONSOMMATEUR : Conservez

cette notice pour consultation

ultérieure.

Casier de Poêle traditionnel Madrona

MFCS01 (noir) ou MFCS02 (brun Majolica)

Certiﬁée pour usage avec foyers Valor MF28 seulement

GUIDE D’INSTALLATION

Madrona

Les articles suivants sont requis pour l’installation :

• Foyer Madrona MF28 + un des Casier de poêle suivant :

• Noir, devanture arquée : MFCS01-1 + MFCS01-2

• Noir, devanture carrée : MFCS01-1 + MFCS01-3

• Majolica, devanture arquée : MFCS02-1 + MFCS02-2

• Majolica, devanture carrée : MFCS02-1 + MFCS02-3

Poêle traditionnel Madrona MFCS01 ou

MFCS02 -

Devanture arquée

Foyer Madrona—MF28

(vendu séparément)

Foyer Madrona—MF28

(vendu séparément)

Poêle traditionnel Madrona MFCS01 ou

MFCS02 -

Devanture carrée

Concept

Contenu du kit

POÊLE NOIR :

Devanture arquée MFCS01-1 + MFCS01-2

Devanture carrée MFCS01-1 + MFCS01-3

MFCS01-1 - noir

• Plaque de remplissage

• Panneau du dessus

• Pattes (4)

• Panneau côté droit

• Panneau côté gauch

• Quincaillerie

MFCS01-2 - noir

• Panneau de base

• Devanture arquée

• Base de feu traditionnelle

MFCS01-3 - noir

• Panneau de base

• Devanture carrée

MFCS01-1 ou MFCS02-1

MFCS01-2 ou MFCS02-2

MFCS01-3 ou MFCS02-3 Crochets

Devanture carrée

Base

de feu

Panneau

du dessus Plaque de

remplissage

Base

Pattes

Panneau

côté droit

Panneau

côté

gauche

Devanture arquée

Pare-étincelles

POÊLE BRUN MAJOLICA :

Devanture arquée MFCS02-1 + MFCS02-2

Devanture carrée MFCS02-1 + MFCS02-3

MFCS02-1 - majolica

• Plaque de remplissage

• Panneau du dessus

• Pattes (4)

• Panneau côté droit

• Panneau côté gauch

• Quincaillerie

MFCS02-2 - majolica

• Panneau de base

• Devanture arquée

• Base de feu traditionnelle

MFCS02-3 - majolica

• Panneau de base

• Devanture carrée

Andere Handbücher für MADRONA MFCS01

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Valor Herd Handbücher

Valor

Valor Vega 200 Gas Gebrauchsanweisung

Valor

Valor ovation 810 Installationsanleitung

Valor

Valor 910 Brunswick Gebrauchsanweisung

Valor

Valor 550 Bedienungsanleitung

Valor

Valor Ridlington 944 Gebrauchsanweisung

Valor

Valor Portrait Series Bedienungsanleitung

Valor

Valor Madrona MF28EN Handbuch

Valor

Valor Hamlet Handbuch

Valor

Valor Firefox 5 910 Bedienungsanleitung

Valor

Valor ardeche 8121 Installationsanleitung

Valor

Valor The Arden Handbuch

Valor

Valor Madrona MF28ILN Betriebsanleitung

Valor

Valor Portrait President FS Stove 531CSB Bedienungsanleitung

Valor

Valor The Arden Handbuch

Valor

Valor MADRONA MF28JN Planungshandbuch

Valor

Valor 550 Bedienungsanleitung

Valor

Valor Willow Handbuch

Valor

Valor Inspire L Gebrauchsanweisung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

Parmco

Parmco FS 600 Bedienungsanleitung

MCZ

MCZ SUITE AIR 10 M2 Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung