Vanco PULSEAUDIO RPA66MK2 Bedienungsanleitung
vanco1.com | 800.626.6445
6x6 audio matrix with 6 bridgeable zones to
accomodate 1 or 2 speakers per zone
6X6 AUDIO DISTRIBUTION
AMPLIFIER
VANCO PART NUMBER PA66MK2
2
1. Do not expose this unit to water,
moisture, or excessive humidity.
2. Do not install or place this unit
in a built-in cabinet, or other
confined space without adequate
ventilation.
3. To prevent risk of electrical shock
or fire hazard, due to overheating
do not obstruct unit’s ventilation
openings.
4. Do not install near any source of
heat, including other units that
may produce heat.
5. Do not place unit near flames.
6. Only clean unit with a dry cloth.
7. Unplug unit during lightening
storms or when not used for
an extended period of time.
A surge protector is strongly
recommended.
8. Protect the power cord from being
walked on or pinched, particularly
at the plugs.
9. Use unit only with accessories
specified by the manufacturer.
10. Refer all servicing to qualified
personnel.
WARNING
CAUTION
THIS PRODUCT IS 100% INSPECTED AND TESTED IN THE
UNITED STATES TO VERIFY PERFORMANCE PARAMETERS.
Thank you for purchasing this product. For optimum
performance and safety, please read these instructions
carefully before connecting, operating or adjusting this
product. Please keep this manual for future reference.
DEAR CUSTOMER
3
The PA66MK2 is a functional, easy-to-install, highly compatible, expandable,
and user-friendly audio distribution system. It provides up to 25W @ 8 Ohm
Power by Class D amplifier to up to 18 zones which at can be controlled by
keypads (sold separately as PA66ACCS), RS232, IR, or via IP with provided
RS232-IP and iOS and Android apps. Overall the distribution system is easy-to
install, so every audiophile can enjoy the powerful audio wherever they are.
6x6 AUDIO DISTRIBUTION AMPLIFIER
Part # PA66MK2
• 6 x 6 Audio Matrix with 6 Bridgeable zones to accommodate 1 or 2 speakers per
zone
• Provides a Whole House Audio Control System - expandable up to 3 units for 18
Zones of distributed audio
• RS232-IP adapter and Android and IOS app allows for eortless control via
smartphone or tablet
• Optional keypads with modern design fit seamlessly into any room. Keypads are
POE with built-in IR Receivers (Keypads and 1 Cat5e/Cat6 Connection Hub sold
separately as PA66ACCS)
• High eciency Class D amplification
• Stereo/Bridge mono output
• Stereo/Bridge mode adjustable
• RS-232 port allows 2-way communication with 3rd party control systems
• Power 230V and 115V adjustable
• Ext. Mute & System on 3.5mm Mono Mini Phone Jacks
• 6 IR Emitter 3.5 mm Mono Mini Phone Jacks + 1 IR Emitter 3.5mm Mono for All
Output Jack
• 1 PA Input Jack to set all Zone to Source 1
• 6 Zone Pre-AMP outputs to connect external power amplifier
FEATURES
4
SPECIFICATIONS
Watts @8ohms .................................................25W x 2 per zone
Watts @4ohms ..................................................50W x 2 per zone
Watts Bridge 8 Ohms......................................100W per zone
S/N..........................................................................>85dB A WTD
THD.........................................................................<0.1%
Frequency Response.......................................20Hz-20KHz
Input Impedance ...............................................>47 K Ohm
Input Sensitivity.................................................250 mv
Protection Function .........................................Overload Protection, Short Circuit
Protection, Over Temperature Protection
System on Voltage ...........................................DC +12V
External Mute Voltage.....................................DC +12V
Power Supply .....................................................AC115V/60Hz, 230V/50Hz
Output Connection ..........................................Terminal Block
Dimension ............................................................16.9”W x 3.5”H x 16.4”D
Weight ..................................................................25 lbs
5
PACKAGE CONTENTS
• 6x6 Amplifier
• Remote Control
• RS-232 IP Adapter
• Expansion Ribbon Cable
• Rack Mounting Ears – 2 (Installed on
Amp)
• Speaker Terminal Blocks – 6 (Installed
on Amp)
• AC Power Cable
• Product Manual
• Remote Control
• Keypad Connection Hub and Decora
Wall-plate
• Keypad Mounting Hardware
• Keypad hub
• (6) PoE Keypads with built-in IR RX and
decora wall plates
• IR Receiving Cable
• AC Power Cable
• Product Manual
PA66MK2: PA66ACCS:
(sold separately)
6
PANEL DESCRIPTIONS
1. Power ON/OFF Switch
2. PEAK LED indicates if a connected source level is too high. If the PEAK
LED is RED, reduce the zone input or output level
3. Standby/Zone ON LED- When this LED is BLUE this indicates a zone is not
on or in Standby mode. When this LED is WHITE it indicates that a zone is
on
1. Stereo line-level Pre-Amp outputs
(Zones 1-6)
2. Mode Switch: Mono/Bridge
3. Speaker Outputs: 50w @ 4 Ohms-
Stereo, 25w @ 8 Ohms-Stereo,
100w @ 8 Ohms-Bridge
4. Source Inputs (Input 1/PA)
5. Status: Used to control external
zone devices
6. IR Outputs to control sources
7. A) PA Trigger IN (Source 1)
B) MUTE In/Control Out: This input
can temporarily mute the system
by connecting this unit to a relay
closure switch on home automation
system or phone system etc. When
switch is on, it will short-circuit the
input and mute the unit.
8. IN/OUT Port: Daisy-chain additional
PA66MK2 units (up to 3 maximum)
9. RS-232 Port
10. Voltage Selector (115v~230v)
11. AC Input (connect included power
cord)
12. Keypad Hub Input (for optional
PA66ACCS)
13. ACG (Automatic Gain Control):
brings low input levels up to a
preset-level
14. Unit ID Switch
1
2
3
12
3
4
5
6
10
89
11
14
13
12
7
7
CONNECT AND OPERATE
Before you begin to install the PA66MK2, it is important to implement good installation
practices:
1. Make sure that AC power is disconnected before making ANY connections
to the main unit and attached devices.
2. Install in a well-ventilated environment
3. Ensure any vents are not blocked to allow for proper circulation
4. Do not install above or below sources of heat
5. Use good quality cabling
6. The unit can be installed within a rack using the provided mounting rack
ears
8
Up to 6 sources can be connected to a single PA66MK2 amplifier. Using RCA
cables connect each source into one of the available Source Inputs.
Some sources such as MP3 players and Cell Phones may require a 3.5mm
Stereo to RCA Cables in order to connect to the PA66MK2
NOTE: Input 1 can be used as a global input for all zones when a source
is connected to Input 1 and the 12VDC is applied to the PA-IN jack (tip is
positive) then source 1 will broadcast to all zones. If no 12VDC is applied, then
the first input will be operating under normal conditions.
CONNECTING THE SOURCES
9
The PA66MK2 can work with speakers that are 4-8 Ohm. There are two modes
that can be set for dierent setups: Stereo or Bridge. An 8 Ohm speaker can
only be used when in Bridge mode. To choose between modes, use the mode
switch to determine modes for each zone (Number 2 Panel Descriptions, page
5)
Once you have properly identified the desired mode, strip about ¼” of
insulation and twist the copper strands. Connect the speaker wire to there
screw down terminal as indicated on the amp. To loosen the terminal turn
counterclockwise and to tighten the terminal turn clockwise. For better
quality, we recommend used 12-14 AWG stranded copper speaker wire.
CONNECTING THE SPEAKERS
10
USING THE PRE-AMP OUTPUTS
There are 6 unbalanced, line level Pre-Amp outputs that correspond to each
of the 6 outputs. These can be used to connect an additional amplifier, expand
zones, or to connect a powered subwoofer. The Pre-amp output levels are
not fixed and are able to be controlled via RS232 and IP using the provided
RS232-IP adapter, as well as keypads and IR sold separately in the PA66ACCS.
Inhaltsverzeichnis
Andere Vanco Verstärker Handbücher
Vanco
Vanco Pulse Audio PA230WP Bedienungsanleitung
Vanco
Vanco PulseAudio PA230BWA Bedienungsanleitung
Vanco
Vanco D2.1 Bedienungsanleitung
Vanco
Vanco HD4KCLK Bedienungsanleitung
Vanco
Vanco Beale Street Audio BAV4250 Bedienungsanleitung
Vanco
Vanco Spot for Dot Bedienungsanleitung
Vanco
Vanco PulseAudio PA230SWA Bedienungsanleitung
Vanco
Vanco AMP200 Bedienungsanleitung
