Vango Evolution EVMX8X6 Bedienungsanleitung
4K 8x6 HDBaseT™
Matrix Switcher with
2 HDMI Outputs, IR,
IP and RS-232
Part Number:
EVMX8X6
www.vanco1.com • 800.626.6445
4K HDBaseT™8x6
MAT R I X
with 2 HDMI Outputs, IR, IP and RS-232
www.vanco1.com 800.626.6445
2
1. Do not expose this unit to water, moisture, or
excessive humidity.
2. Do not install or place this unit in a built-in
cabinet, or other conned space without
adequate ventilation.
3. To prevent risk of electrical shock or re
hazard, due to overheating do not obstruct
unit’s ventilation openings.
4. Do not install near any source of heat,
including other units that may produce heat.
5. Do not place unit near ames.
6. Only clean unit with a dry cloth.
7. Unplug unit during lightening storms or when
not used for an extended period of time. A
surge protector is strongly recommended.
8. Protect the power cord from being walked on
or pinched, particularly at the plugs.
9. Use unit only with accessories specied by
the manufacturer.
10. Refer all servicing to qualied personnel.
CAUTION
HDMI is a very complex technology requiring continuous authentication of the signal and the same
video resolution and audio settings on all electronic equipment in the system. When there are multiple
sources and displays, the video resolution and audio setting on all connected units must be adjusted
to correspond with that of the display having the lowest video and audio capability.
WARNING
DEAR CUSTOMER
Thank you for purchasing this product.
For optimum performance and safety, please
read these instructions carefully before connecting, operating or
adjusting this product. Please keep this manual for future reference.
This product is 100% inspected and tested in the United States to verify
HDMI performance parameters.
www.vanco1.com 800.626.6445 3
INTRODUCTION
The Evolution by Vanco EVMX8X6 4K HDBaseT™ Matrix Switcher with 2 HDMI Outputs, IR, IP and RS-232 allows 8 HDMI
sources to be distributed to up to 8 displays simultaneously, with 6 of the outputs over Cat6 using HDBaseT transmission
and 2 outputs over HDMI. The EVMX8X6 is capable of transmitting 4K@60Hz, 4:4:4 Chroma Subsampling, and HDR up to
131ft/40m over a single Cat6 cable, and 4K@60Hz, 4:4:4 Chroma Subsampling with HDR10 and Dolby Vision on the HDMI
inputs and HDMI outputs. For control, the EVMX8X6 features multiple methods including simple control using the front
panel control, IR control, and an easy to use UI accessible via IP. Control switching sources to displays from a computer or
a wireless device such as a tablet or mobile phone. The EVMX8X6 is compatible with both the EVRXHD2 and EVRXDSC
HDBaseT receivers for additional exibility. For switching multiple sources to multiple displays using HDBaseT technology, with
many features for control, audio, 4K HDR resolution, and scaling, the EVMX8X6 is a great choice for any application.
FEATURES
4K 8x6 HDBaseT™ Matrix Switcher with 2 HDMI Outputs, IR, IP
and RS-232
Part # EVMX8X6
• 4K 8x6 HDBaseT Matrix that accommodates 6 HDBaseT outputs and 2 HDMI outputs
• Extends 4K@60Hz 4:4:4, and HDR10 up to 131ft/40m over a single Cat6 cable
• Outputs 4K@60Hz 4:4:4, HDR10 and Dolby Vision on the HDMI inputs and outputs
• Extends 1080p resolution up to 230ft/70m over a single Cat6 cable
• PoC receivers sold separate (EVRXHD2 and EVRXDSC)
• Features POC (Power over Cable) technology - providing power for the receivers resulting in easy
installation
• HDCP 2.2 compliant
• Digital and analog audio breakouts for the HDMI outputs
• Built-in EDID management and advanced HDCP handling
• Controllable via front panel, IR, RS-232 and third party control systems, as well as a built in GUI via IP
connection
• Features bi-directional IR and RS-232 for source and/or display control
• Includes EV-IRMST IR integration cable for seamless integration with 3rd Party IR Systems
• Dimensions: 17.2” W x 1.7” H x 15” D
• EVMX8X6 HDBaseT Matrix Switcher
• (2) Mounting Ears with 6 Screws
• (4) Plastic feet
• (1) IR Remote
• (8) IR Receivers
• (9) IR Emitters
• (1) RS-232 Cable (3-pin to DB9)
• (1) IR Control Cable (EV-IRMST)
• (1) Power Supply (24V DC 2.71A)
• (1) Product Manual
PACKAGE CONTENTS
www.vanco1.com 800.626.6445
4
SPECIFICATIONS
Video Input................................................................ (8) HDMI
Video Input Connector ................................................ (8) Type-A Female HDMI
Video HDMI Input Resolution....................................... Up to 4K@60Hz 4:4:4, HDR10, Dolby Vision
Video Output ............................................................. (6) HDBaseT, (2) HDMI
Video Output Connector.............................................. (6) RJ45, (2) Type-A female HDMI
Video HDMI Output Resolution .................................... Up to 4K@60Hz 4:4:4, HDR10, Dolby Vision
Video HDBaseT Output Resolution ............................... Up to 4K@60Hz 4:4:4, HDR10
Video HDMI Audio Signal ........................................... LPCM 7.1 audio, Dolby Atmos®, Dolby®TrueHD,
Dolby Digital® Plus, DTS:X™, and DTS-HD® Master Audio™ pass-through
Audio Output ............................................................. (2) SPDIF, (2) RCA (L+R)
Audio Output Connector ............................................. (2) Toslink connectors, (4) 3.5mm jacks
Digital SPDIF Audio Format......................................... Supports PCM, Dolby Digital, DTS, DTS-HD
Analog RCA (L+R) Audio Format.................................. Supports PCM
Frequency Response .................................................. 20Hz – 20KHz, ±3dB
Audio Output Impedance............................................. 70 Ohms
Max Input Level .........................................................
RCA: 2.0Vrms ± 0.5dB. 2V = 16dB headroom above -10dBV (316mV) nominal consumer line level signal;
SPDIF:±0.05dBFS
THD+N ..................................................................... < 0.05% (-80dB), 20Hz – 20KHz bandwidth, 1KHz
sine at 0dBFS level (or max level)
SNR ......................................................................... RCA: > 80dB, 20Hz - 20KHz bandwidth;
SPDIF: > 90dB, 20Hz-20 kHz bandwidth
www.vanco1.com 800.626.6445 5
SPECIFICATIONS
Crosstalk Isolation ..................................................... RCA: < -80 dB, 10KHz sine at 0dBFS level (or max
level before clipping); SPDIF: < -70 dB, 10KHz sine at 0dBFS level (or max level before clipping)
L+R Level Deviation.................................................... RCA: < 0.3dB, 1KHz sine at 0dBFS level (or max
level before clipping)
Frequency Response Deviation .................................... < ± 0.5dB 20Hz - 20KHz
Output Load Capability ............................................... RCA: 1KΩ and higher (Supports 10x paralleled 10KΩ
loads)
Stereo Channel Separation.......................................... >70dB@1KHz
Noise Level ............................................................... RCA: -80dB; SPDIF: -90dB
Control Port .............................................................. (1) FW, (6) IR IN, (1) IR ALL IN, (8) IR OUT, (1) IR
ALL OUT, (1) IR EYE, (1) RS-232, (1) TCP/IP
Control Connector...................................................... (1) Type-A USB, (17) 3.5mm jacks, (1) 3-pin terminal
block, (1) RJ45
Transmission Mode .................................................... HDBaseT
Transmission Distance................................................ 1080p ≤ 230 feet (70 meters), 4K@60Hz ≤ 131
feet (40 meters)I
Bandwidth................................................................. 18 Gbps
Operation Temperature............................................... -5 to +55° (+23° to +131°F)
Storage Temperature ................................................. -25 to +70° (-13° to +158°F)
Relative Humidity....................................................... 10% to 90%, Non-condensing
External Power Supply ................................................ 100V~240V AC, 50/60Hz
Power Consumption ................................................... 92W (Max)
Dimensions ............................................................... 17.2” W x 1.7” H x 15” D
Weight ..................................................................... 8 lbs
www.vanco1.com 800.626.6445
6
Front Panel
1. POWER LED: Illuminates red when the device is in standby mode, illuminates green when device is
powered on
2. INPUTS: Inputs 1-4 source selection (buttons will turn blue when selected)
3. OUTPUTS: Outputs 1-4 display selection (buttons will turn blue when selected)
4. Menu Buttons:
• ENTER: Switches input(s) to output(s) after input/output selection
• LOCK: Locks/Unlocks front panel buttons
• ALL: Selects all inputs and/or outputs for switching
• CLEAR: Cancel
5. PRESET RECALL: There are up to 4 presets which can be saved for easy switching to any source/display
conguration
• Press and hold any preset button 1-4 to save the current switching status, this saves the current
conguration to be quickly easily called back
PANEL DESCRIPTIONS
3 4 5
1
2
www.vanco1.com 800.626.6445 7
6
Rear Panel
1. INPUTS: Connect HDMI sources to each corresponding HDMI input
2. OUTPUTS:
• 1-6-HDBT: Connect HDBaseT receiver(s) to each output, option of the EVRXHD2 or EVRXDSC PoC
receivers
• 7-8-HDMI: Connect HDMI displays via HDMI cables; if needing to extend this signal over Cat5e/6, an
HDBaseT extender is strongly recommended
3. IR OUT:
• 1-8: Connect the included IR Transmitters (TXs) to each port, the number on the IR output corresponds
to the HDMI inputs. Connect this if you would like to control the sources from each display location over
HDBaseT (receiver(s) have IR inputs)
• ALL OUT: Connect the included IR Transmitter (TX) to this port, this will send an IR signal from any
HDBaseT receiver regardless of the HDMI signal routing; useful feature to turn on/off an external
amplier or audio distribution system at any display location
4. IR IN:
• 1-6: Connect the included IR Receivers (RXs) to each port, the number on the IR input corresponds to
the HDBaseT outputs. Connect this if you would like to control the display(s) over HDBaseT (receiver(s)
have IR outputs)
• ALL IN: Connect the included IR Receiver (RX) to this port, this will send an IR signal out to all HDBaseT
receiver(s); useful feature to turn on/off all displays at one time
5. AUDIO OUTPUTS: Digital optical outputs and analog RCA outputs for HDMI outputs 7 and 8
6. CONTROL:
• TCP/IP: Connect to a local network such as a router or ethernet switch to give the matrix unit
connectivity, this will give the ability to control the matrix unit via IP with any device on the network such
as a computer, tablet, or mobile phone
• RS-232: Connect the included RS-232 cable to a computer or 3rd party control system for integration
• IR EYE: Connect the included IR Receiver (RX) to this port, this can be used to control the matrix unit
with the included IR remote; also a helpful feature to hide the matrix unit and lead out the IR Receiver to
a different location for remote control
• FIRMWARE: Connect a Type-A USB cable to upgrade rmware, any available rmware updates will be
located on the product page for this part # on www.vanco1.com, under the “downloads” tab
7. DC 24V: Connect the included power supply
345
2
1
www.vanco1.com 800.626.6445
8
1. Connect HDMI sources to the HDMI inputs of the EVMX8X6 (NOTE: HDMI certied cables are strongly
recommended for 4K HDR resolution)
2. Connect Cat6 cables from the matrix unit outputs to each display location (NOTE: home run Cat5e/6
cables are strongly recommended as any coupling points such as punch down RJ45 jacks, female/female
RJ45 jacks, etc. can cause signal degradation. Patch panels will cause even more signal degradation.)
3. Connect the HDBaseT Receivers to outputs 1-6, option of either the EVRXHD2 or EVRXDSC; connect
HDMI cables from the receivers to each HDMI display (NOTE: HDMI certied cables are strongly
recommended for 4K HDR resolution)
4. Connect an HDMI display to output 7 and 8 (NOTE: HDMI certied cables are strongly recommended for
4K HDR resolution)
5. OPTIONAL: Connect an external amplier or AV Receiver to the digital and/or analog output (NOTE: both
the digital optical and analog RCA audio breakouts follow outputs 7 and 8 only)
6. OPTIONAL: Connect a router or ethernet switch to the TCP/IP RJ45 jack on the EVMX8X6, this will
connect the matrix unit to the network, and can be controlled via IP
7. Connect the included power supply
CONNECT AND OPERATE
www.vanco1.com 800.626.6445 9
FRONT PANEL CONTROL
The matrix switcher can be controlled by using the buttons on the front panel. Whenever a command is
accepted, all the pressed buttons will blink three times then they will go off. If there is no other action after
pressing the input/output button, the buttons will go off after eight seconds.
5.1 Signal Switching (S= Source; D= Display)
• Switch an input to an output
Operation: INPUT# + OUTPUT# + ENTER
Example: Switch Input 1 to Output 2:
• Switch an input to multiple outputs
Operation: INPUT# + OUTPUT# + OUTPUT# +… + ENTER
Example: Switch Input 1 to Output 2, 3, and 4
Press
Press
• Switch an input to all outputs (split one source to all displays)
Operation: INPUT# + ALL + ENTER
Example: Switch Input 1 to all outputs
Press
www.vanco1.com 800.626.6445
10
5.2 Switching Status Inquiry (nd out what source is being sent to a certain display
Press and hold the OUTPUT# you would like to see the status of, the corresponding input button will illuminate
blue. The button illumination will turn off when releasing the OUTPUT# button.
5.3 Panel Button Locking/Unlocking
Press and hold LOCK button for 3 seconds to lock front panel buttons, it will illuminate blue to conrm. Press
and hold the button again to unlock.
5.4 Preset Setting (a quick and easy way to save and recall a conguration without
having to manually switch each input/output)
Press and hold the PRESET 1-4 for 3 seconds to save the current switching status to the corresponding
preset 1-4.
Press the PRESET 1-4 o recall the saved preset 1-4.
Note: The front panel only holds 4 presets, however the UI via IP control gives the ability of saving up to 9
presets.
5.5 CLEAR Button (cancel)
Press the CLEAR button to cancel
USER INTERFACE CONTROL
The matrix switcher can be controlled via TCP/IP. Connect the EVMX8X6 to a router or ethernet switch to
connect to the local network. The default IP address and settings are:
IP Address 192.168.0.178
Subnet Mask 255.255.255.0
Type 192.168.0.178 into the address bar on any internet browser such as a connected PC, tablet, or mobile
phone, the following webpage should appear:
Inhaltsverzeichnis
