VANMOOF X3 Bedienungsanleitung
3
BUILD YOUR BIKE
Build your bike
Table of contents
The toolbox
Take the bike out of the box
Get your toolbox ready
Adjust the stem
Wheel position
Brake disc covers
Brake disc alignment
Wheel alignment
Connect the motor cable
Attach the pedals
Check your handlebar
p.5
p.7
p.7
p.8
p.8
p.10
p.11
p.12
p.12
p.14
p.15
p.17
p.18
p.18
p.19
p.20
p.20
p.21
p.22
p.23
p.23
p.24
p.31
p.32
p.32
p.33
p.34
p.35
p.26
p.28
Saddle adjustment
Adjusting the handlebar height
Matrix Display
Inate your tires
Activating your Electried
Handlebar buttons
Locking your bike
Unlocking when connected
Unlocking when not connected
Power assist level
Controlling the lights
Power and reset
Charging
Bike basics
Chainguard and cleaning
Screw connections
Replacing parts
Warranty
Warnings
The rst ride
Find your t Love your bike
Build your bike
The toolbox
Take the bike out of the box
Get your toolbox ready
Adjust the stem
Wheel position
Brake disc covers
We know you can’t wait to get riding
– this won’t take long, promise.
Brake disk alignment
Wheel alignment
Connect the motor cable
Attach the pedals
Check your handlebar
5
BUILD YOUR BIKE
Tire pump
Allen key #3, #5 & #6
Anti-theft nut tool
Charger
Anti-theft torx key
Anti-theft nut 2x
Anti-theft wrenchWashers 2x
Cable cover bolts 2x
Handlebar spacers Cable cover
Chain lubricant
The toolbox
6
BUILD YOUR BIKE
VanMoof X3
VanMoof S3
Charging port
Electronic shifter
Sensor
Matrix Display
Reset button
Motor
Front lightRear light
Battery
Smart Cartridge
Kick Lock
Charging port
Sensor
Matrix Display
Reset button
Motor
Front light
Rear light
Battery
Smart Cartridge
Electronic shifter
Kick Lock
7
BUILD YOUR BIKE
ToolboxFront wheel stand
1.1 To take the bike out of the box, gently
pull the yellow strap.
1.2 Remove (and recycle) all protective
packaging. Squeeze the tab on the
cable ties to remove them without
cutting – you can reuse them later.
2.1 Take the toolbox out of the triangular
front wheel stand – you’ll nd it at the
front side of the stand.
2.2 Make sure you detach the wheel from
the bike frame.
1. Take the bike out of the box
2. Get your toolbox ready
8
BUILD YOUR BIKE
90°
Place on the oor
3.1 Rotate the stem 90° clockwise so it’s in
line with the front fender.
4.1 Take the bike out of the front wheel
stand and place it on the oor.
3. Adjust the stem
4. Wheel position
Note
See page 28 to learn how to
adjust the handlebar.
3.2 Now tighten the two bolts using the
Allen key #5, making sure the stem
stays in line with the front wheel.
Allen key #5
9
BUILD YOUR BIKE
Front wheel stand
Motor cable
facing down
4.3 Looking down from a riders position,
the motor cable attached to the wheel
should be on the right side and facing
down.
4.2 Put the front wheel in the front wheel
stand.
10
BUILD YOUR BIKE
Plastic insert
5.1 Remove the plastic insert from the
brake calliper. Make sure you don’t
squeeze the brake levers while doing
this.
5. Brake disc cover
5.2 Carefully lift up the bike and guide the
front fork onto the wheel.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere VANMOOF Fahrrad Handbücher
