Varimixer W30 Bedienungsanleitung

Andere Handbücher für W30

1

Dieses Handbuch passt für folgende Modelle

1

Inhaltsverzeichnis

Andere Varimixer Mischer Handbücher

Varimixer

Varimixer V80 Leitfaden

Varimixer

Varimixer W80 Bedienungsanleitung

Varimixer

Varimixer V30K Leitfaden

Varimixer

Varimixer W20SF Bedienungsanleitung

Varimixer

Varimixer W20P Bedienungsanleitung

Varimixer

Varimixer W20D Leitfaden

Varimixer

Varimixer TEDDY W5A Bedienungsanleitung

Varimixer

Varimixer W40(A) Leitfaden

Varimixer

Varimixer W20 F Leitfaden

Varimixer

Varimixer AR100 VL-1L Bedienungsanleitung

Varimixer

Varimixer V5A TEDDY Leitfaden

Varimixer

Varimixer KODIAK V20KT Leitfaden

Varimixer

Varimixer KODIAK10 Bedienungsanleitung

Varimixer

Varimixer AR80 Series Bedienungsanleitung

Varimixer

Varimixer V80 Bedienungsanleitung

Varimixer

Varimixer V30K Leitfaden

Varimixer

Varimixer V30 Bedienungsanleitung

Varimixer

Varimixer W80 Leitfaden

Varimixer

Varimixer V20K Leitfaden

Varimixer

Varimixer RV 10 VL-2 Bedienungsanleitung

Varimixer

Varimixer KODIAK20 Bedienungsanleitung

Varimixer

Varimixer W80A Bedienungsanleitung

Varimixer

Varimixer RN Series Bedienungsanleitung

Varimixer

Varimixer W30 Leitfaden

Beliebte Mischer Handbücher anderer Marken

Bosch

Bosch GRW 9 Bedienungsanleitung

MULTIQUIP

MULTIQUIP Whiteman WM45E Leitfaden

KitchenAid

KitchenAid KSM7581BZ0 Kurzanleitung

Jay-Lor

Jay-Lor 5050 Bedienungsanleitung

Sunbeam

Sunbeam FPSBSM210X Bedienungsanleitung

MULTIQUIP

MULTIQUIP Whiteman MC94S Leitfaden

Thinky

Thinky ARE-250 Bedienungsanleitung

Midas

Midas XL4 Bedienungsanleitung

bianco

bianco PURO 4 Bedienungsanleitung

Paso

Paso DAG9200 Bedienungsanleitung

Sima

Sima SFX-9A Bedienungsanleitung

better chef

better chef IM-815WC Montageanleitung

ALLEN & HEATH

ALLEN & HEATH GR1 Bedienungsanleitung

Lacor

Lacor 69083 Technisches Datenblatt

M-Audio

M-Audio Midiman SAM Bedienungsanleitung

Buffalo

Buffalo CP921 Bedienungsanleitung

Pentair

Pentair HYPRO Cleanload 3376-0870 Betriebsanleitung

Cuisinart

Cuisinart SM50WHE Bedienungsanleitung

PLEASE REFER TO THE DIAGRAM ON PAGE 2

1REMOVE NUT (J) AND SHIM WASHERS (H)

2 PRY OFF FORK ASSEMBLY (X).

3 REMOVE SPECIAL V-BELT (A).

4 REMOVE TWO 17MM BOLTS (V)

5 REMOVE 4 BOLTS FROM MOTORPLATE (T).

6 ON OLDER MODEL MIXERS WITH SINGLE PHASE MOTORS,IT MAY BE NECESSARY

TO DISCONNECT THE START & RUN CAPACITORS FROM THE SIDE OF THE

MOTOR BEFORE LIFTING THE MOTOR OUT OF THE MIXER.

7 LIFT MOTOR OUT OF MIXER BODY. SET MOTOR ASSEMBLY ON A BOARD LAYED

ACROSS THE TOP OF THE MIXER.

8 DISCONNECT WIRE HARNESS FROM MOTOR.

NOTE: DO NOT FOLLOW STEPS 9-12 IF YOU ARE REPLACING THE WHOLE

ASSEMBLY. (MOTOR ,GEARBOX,MOTOR PLATE AND PULLEY.

9 GRASP TOP PULLEY (W) AND BANG AGAINST CLAMPING RING & WASHER (S)

THIS ACTION WILL REMOVE PULLEY FROM MOTOR SHAFT.

10 REMOVE 4 SLOTTED HEAD SCREWS FROM MOTOR PLATE TO MOTOR.

REMOVE MOTOR PLATE.

11 INSTALL MOTOR PLATE ONTO MOTOR,TIGHTEN 4 SLOTTED HEAD SCREWS.

INSURE CAPACITORS WILL FACE THE REAR OF THE MIXER WHEN MOTOR IS

INSTALLED.

12 INSTALL MOTOR PULLEY ONTO MOTOR SHAFT,TAKING CARE TO ALIGN KEY WITH KEYWAY. BANG TOP PULLEY AGAINST BOTTOM

PULLEY UNTIL INSTALLED.

13 PLACE MOTOR ON TOP OF MIXER AND CONNECT MOTOR TO HARNESS. (FOLLOW DIAGRAM

ON MOTOR)

14 LOWER MOTOR INTO MIXER BODY.INSTALL 4 BOLTS (T) TO THE MOTOR PLATE. DO NOT TIGHTEN!

15 INSTALL 2 17MM BOLTS (V)

16 MEASURING THE DISTANCE BETWEEN PULLEYS (B),ON 30QT. & 40 QT. THE

DISTANCE SHOULD BE 11 1/2 INCHES.SLIDE MOTOR TO REACH THIS DISTANCE.

ON 60QT.-150QT.,THE DISTANCE SHOULD BE 12 1/4"S.

17 TIGHTEN 13 MM BOLTS (T) AND 17 MM BOLTS (V).

NEXT PAGE

Motor Removal Instructions

Models W30-W150

Motor Removal Instructions

Models W30-W150

18 INSTALL SPECIAL V-BELT (A).

19 INSTALL FORK ASSEMBLY (X).

20 INSTALL WASHERS (G) (H) AND NUT (J).DO NOT TIGHTEN NUT.

21 START THE MIXER AND TIGHTEN THE NUT (J).

DO NOT OVERTIGHTEN!

22 ON THE FRONT PULLEY SET,THE STUD (K) ON THE VARISPEED COLLAR (L) MUST BE PLACED

INSIDE THE LOWER FORK (M),AND ON THE REAR PULLEY SET OUTSIDE THE FORK (N).

23 ADJUST THE SPEED BY TURNING THE THE STOP SCREWS (O) IN OR OUT.

24 THE STOP SCREWS (O) ON THE SPEED LEVER SHOULD BE ADJUSTED SO THAT THE

MEASUREMENT (P) IS 1-2MM ON THE FRONT AND REAR PULLEY,AT HIGH AND LOW SPEED,

RESPECTIVELY.TIGHTEN THE JAM NUTS (R) WHEN THE SPEED IS CORRECTLY ADJUSTED.

Motor Removal Instructions

Models W30-W150