VDH ALFA 71 MODulation Bedienungsanleitung

User manual

ALFA 71 MODulation

Thermostat.

0-100C

VDH doc. 080349 Version: v1.0 Date: 07-03-2008

Software: ALFA71MOD100 File: DO080349.WPD Range: 0/+100,0C

*Installation.

On the top side of the ALFA 71 MOD is shown how the sensors, power supply and relays has to be

connected.

After connecting the ALFA 71 MOD to the power supply, a self test function is started. As this test

is finished the measured temperature appears in the display.

*Control.

The ALFA 71 MOD thermostat can be controlled by four pushbuttons on the front. These keys are:

SET - view / change the setpoint.

UP - increase the setpoint.

DOWN - decrease the setpoint.

C- hidden push button above the SET key and behind Csymbol.

*Viewing set point.

By pushing the SET key the set point appears in the display. The decimal point of the last display

starts blinking. A few seconds after releasing the SET key the setpoint disappears and the

measured temperature is shown again in the display.

*Changing set point.

Push the SET key and the set point appears in the display. Release the SET key. Now push the

SET key again together with the UP or DOWN keys to change the setpoint. A few seconds after

releasing the keys the measured temperature shows again in the display.

*Status of the Relays.

By pushing the hidden Ckey the display shows the status of the relays. Each display segment

shows the status of the relay output, showing 0=off and 1=on. The code 110 means relay 1 and 2

are on and relay 3 is off.

*Readout valve position.

By pushing the UP key the display shows the current valve position.

*Setting internal parameters.

Next to the adjustment of the setpoint, internal settings can be made like differential, sensor-offset,

setpoint range and the functions of the thermostat.

Push the DOWN key more than 10 seconds, to enter the 'Internal Programming Menu'. In the left

display the upper and lower segment are blinking. Over the UP and DOWN keys the required

parameter can be selected (see table for the parameters).

If the required parameter is selected, the value can be read-out by pushing the SET key. Pushing

the UP or DOWN key to change the value of this parameter.

If after 20 seconds no key is pushed, the ALFA 71 MOD changes to the normal operation mode.*

Adjustment sensors.

The temperature sensor can be adjusted by using the Sensor Offset parameter 05.

Indicates the Sensor e.g. 2C to much, the Sensor Offset has to be decreased with 2C.

*Error messages.

In the display of the ALFA 71 MOD the following error messages can appear:

LO - Minimum alarm. Solution E1:

HI - Maximum alarm. - Check if the sensor is connected correctly.

E1 - Sensor-1 failure. - Check sensor (1000at 25C).

- Replace sensor.

EEE - Settings are lost. Solution EEE:

- Reprogram the settings.

-L- - In case of sensor short-circuit the display alternates between error-code E.. and -L-,

as indication for a short-circuit sensor.

-H- - In case of open-circuit sensor the display alternates between error-code E.. and -H-,

as indication for a open circuit sensor.

Reset Alarm. When a error-messages appears it can be resetted by pushing the SET key.

The function of this key depends on parameter P37.

*Technical details.

Type : ALFA 71 MOD Thermostat

Range : 0/+100,0C, per 0,1C

Supply : 12Vac 50/60Hz (-5/+10%)

Display : 3-digit 7-segment display

Relays : Ry1= Open SPST(NO)250V/8A (cos =1) of 250V/5A (cos =0.4)

Ry2= Close SPST(NO)250V/8A (cos =1) of 250V/5A (cos =0.4)

Ry3= Alarm SPDT(NO/NC)250V/8A (cos =1) of 250V/5A (cos

=0.4)

Relays have one common (C).

Control : By push buttons on front.

Front : Polycarbonate IP65

Sensor : SM 811/2m (PTC 1000/25C).

Analog output : 0..10 Vdc PI output (cool or heat)

Dimensions : 35 x 77 x 71,5mm (HWD)

Panel cutout : 28 x 70mm (HW)

Accuracy : ± 0,5% of the range.

- Provided with memory protection during power failure.

- Connections with screw terminals on the back side.

- Equipped with sensor failure detection.

- Special versions on request available.

*Parameters ALFA 71 MOD

Para-

meter Description Parameter Range Default

01 Function thermostat 1=Cool

2=Heat 1

02 Offset temperature sensor-1 -15.0..+15.0C0.0

P-band

I-time

Runtime valve

Reset time

Reset to minimum or maximum valve

position

0,0..+15,0C

0..99 Minutes

0..999 Seconds

0..999 Minutes

0 = mimimum

1 = maximum

5,0

120

Minimum set point

Maximum set point

Read-out above -10C per 1C

0,0..+100,0

0= no, 1= yes

0,0

+100,0

Alarm type

Minimum alarm set point

Maximum alarm set point

Time delay minimum alarm

Time delay maximum alarm

Relay function alarm relay

Reset alarm relay after recovering

alarm

Reset alarm relay after manual reset

0= None

1= Absolute

2= Relative

0.0..+100.0C

0..99 min.

0= Watch alarm

1= Control

alarm

0= No, 1= Yes

+100

41 Start up delay after power failure

Forced relay function at sensor failure 0..99 Minutes

0= None

1= Min.

2= Max.

Software version

Production year

Production week

Serial number (x1000)

Serial number (units)

0..255

00..99

1..52

0..255

0..999

*Dimensions.

*Connections.

*Address.

VDH Products BV Tel: +31 (0)50 30 28 900

Produktieweg 1 Fax: +31 (0)50 30 28 980

9301 ZS Roden Email: info@vdhproducts.nl

The Netherlands Internet: www.vdhproducts.nl

Andere VDH Thermostat Handbücher

VDH

VDH ALFA D1-DP Bedienungsanleitung

VDH

VDH ALFA 51 Bedienungsanleitung

VDH

VDH ALFA(NET) 71 PI Bedienungsanleitung

VDH

VDH MC 785-DF KLIMA Bedienungsanleitung

VDH

VDH ALFA 75 RTDF Bedienungsanleitung

VDH

VDH ALFA 13 Bedienungsanleitung

VDH

VDH ALFA 71 PI Bedienungsanleitung

VDH

VDH ALFA 75 RTDF Bedienungsanleitung

VDH

VDH ALFA 23 DP Bedienungsanleitung

VDH

VDH ALFA 25 DP Bedienungsanleitung

VDH

VDH ALFA 29 Bedienungsanleitung

VDH

VDH ALFA 71 Bedienungsanleitung

VDH

VDH ALFA 59 Bedienungsanleitung

VDH

VDH ALFA 52-VS Bedienungsanleitung

VDH

VDH ALFANET51 RTDN Bedienungsanleitung

VDH

VDH ALFA(NET) 31 Bedienungsanleitung

VDH

VDH ALFA 30 Bedienungsanleitung

VDH

VDH ALFA(NET) 33 Bedienungsanleitung

VDH

VDH ALFANET 71 Bedienungsanleitung

VDH

VDH ALFA 71 Bedienungsanleitung

VDH

VDH ALFANET 71-2SP Bedienungsanleitung

VDH

VDH ALFA(NET) 52 Bedienungsanleitung

VDH

VDH ALFANET 71 Bedienungsanleitung

VDH

VDH ALFA 35 DP Bedienungsanleitung

Beliebte Thermostat Handbücher anderer Marken

EWELLY

EWELLY EW-181 Bedienungsanleitung

Prolon

Prolon T1100 Montageanleitung

Computherm

Computherm Q20 Bedienungsanleitung

Heatmiser

Heatmiser neoStat Bedienungsanleitung

Aube Technologies

Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung

Mars

Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung

Saswell

Saswell SAS920XWHB-7-S-RF Leitfaden

Aircalo

Aircalo TFP1-ET85P2 Bedienungsanleitung

Honeywell

Honeywell CM721 Bedienungsanleitung

Carrier

Carrier DEBONAIR 33CS Bedienungsanleitung

Lennox

Lennox iHarmony Zone Thermostat Montageanleitung

Gemtech

Gemtech GT7000 Bedienungsanleitung

Rollei

Rollei Smartes 45000 Bedienungsanleitung

Sinope

Sinope TH1300RF Bedienungsanleitung

Honeywell

Honeywell RLV4305 Bedienungsanleitung

Honeywell

Honeywell Prestige 2.0 THX9421 Bedienungsanleitung

NuTone

NuTone NTBZ48 Original Betriebsanleitung

Stelpro

Stelpro MAESTRO ASMT402AD Bedienungsanleitung