VDL 636134 Bedienungsanleitung

Ref. 636134

DESHUMIDIFICADOR

DEHUMIDIFIER

USER´S MANUAL

MANUAL DEL USUARIO

Please read this manual before use.

Porfavor leer el manual antes de usar

Distribuido por: HORTICULTURA TÉCNICA S.L.U

CIF B97303937

C/ AIGÜADERS Nº4

46680 ALGEMESI VALENCIA ESPAÑA

CONTACTO info@hortec.es

1. Do not use means to accelerate the defrosting

process or to clean, other than those recommended by

the manufacturer.

2. The appliance shall be stored in a room without

continuously operating ignition sources (for example:

open flames, an operating gas appliance or an operating

electric heater.)

3. Do not pierce or burn.

4. Be aware that refrigerants may not contain an odour.

5. Appliance shall be installed, operated and stored in a

room with a floor area larger than 12m2

6. Servicing shall be performed only as recommended by

the manufacturer.

7. The appliance shall be stored in a well- ventilated area

where the room size corresponds to the room area as

specified for operation.

8. All working procedure that affects safety means shall

only be carried by competent persons.

9. Please read the manual carefully before the first time

using this product, and storage the unit in safe place to

avoid electricity leakage, flaming or person injure.

10.Do not put this product in the water or any other

liquids.

11.If the supply cord is damaged, it must be replaced by

the manufacturer, its service agent or similarly qualified

persons in order to avoid a hazard..

12.Please ask professional service agent to repair the

product. Improper repair might cause damage to users.

13.Disconnect the appliance from power supply before

moving or cleaning the product, and also when the product

is not in used.

14.Please operate the product with specified electricity

voltage.

15.Please use this product only for household appliance

and follow the designed purpose.

16.Do not put any stuff on the product.

17.In order to avoid water leakage, please clean the water

tank before moving the product.

18.Do not incline the product, or leaking water may

damage the product.

19.This appliance can be used by children aged from 8

years and above and persons with reduced physical,

sensory or mental capabilities or lack of experience and

knowledge if they have been given supervision or instruc-

tion concerning use of the appliance in a safe way and

understand the hazards involved. Children shall not play

with the appliance. Cleaning and user maintenance shall

not be made by children without supervision.

20.Please keep the product from the wall or other barriers

in a minimum distance of 50 cm.

21.The appliance shall be installed in accordance with

national wiring regulations.

22.The applicable operating temperature range for this

unit is 5-35°C.

23.Do not operate your dehumidifier in a wet room such as

a bathroom or laundry room.

24. Spaces where refrigerant pipes shall be compliance

with national gas regulations.

SAFETY INFORMATION

1. CONTROL PANEL

2. AIR OUTLET

3. HANDEL

4. FRONT HOUSING

5. AIR INLET /

BACK HOUSING

6. DRAIN HOLE

7. WATER TANK

OPERATING

INSTRUCTION

Ref. 636134

DEHUMIDIFIER

DESHUMIFICADOR

1. POWER

Press this key to turn “on” or “off”, and the relating

indicating light may follow the instruction to

illuminate or extinguish. (While the unit is defrost-

ing, the indicating light may lights on and off in

turn shortly.)

2. FAN SPEED

Press the key to choose high speed (HI) or low

speed (LOW), and the relating indicating light may

follow the instruction to illuminate or extinguish.

3. TIMER

a. Press the key to set time you need. (1 to 24

hours)

b. When setting timer in stand-by mode, the unit

will be turned on automatically; when setting timer

in operating mode, the unit will be turned off

automatically.

c. If pressing the power key to turn off the unit

before time finishes counting down, the setting

timer will be canceled.

d. While the timer is in used, the indicating light

illuminates; if not, then the indicating light

extinguishes.

e. After set the timer 5 seconds, the display may

switch back to show the ambient humidity.(Press

once again can show the turning-off time.)

4. HUMIDITY SETTING

Press the key to set the relative humidity you need.

(From continuous dehumidification [CO] to relative

humidity 50%, 60%, 70%, 80%, comfort mode [AU],

and back to continuous dehumidification [CO]. The

first time you electrify the unit, the unit is set to be

continuous dehumidification [CO].

When ambient humidity is lower than setting humidi-

ty by 3%, compressor will stop automatically, and

return working until the ambient humidity is higher

than setting humidity by 3%.

COMFORT MODE [AU]

a. When ambient temperature is lower than 5°C,

compressor will stop working.

b. When ambient temperature is higher than 5°C and

lower than 20°C, the product will set the humidity to

60% automatically.

c. When ambient temperature is higher than 20°C and

lower than 27°C, the product will set the humidity to

55% automatically.

d. When ambient temperature is higher than 27°C, the

product will set the humidity to 50% automatically.

WATER FULL

When the water tank is full, the indicating light will

illuminate and the unit will stop working until empty

the water tank.

DEFROST

When the unit is defrosting, the indicating light will

illuminate and the compressor will stop working but

the motor will keep operating.

WARNING

1. When operating the dehumidifier, please do not set

the humidity higher than ambient humidity.

2. When indicating light illuminates, please pour the

water out of the tank and put it back. Then the

product will resume working.

3. When the product shut down, please wait at least 3

minutes before restarting the unit to prevent damag-

ing the compressor.

CONTROL PANEL DESCRIPTION

OPERATING INSTRUCTION

Ref. 636134

DEHUMIDIFIER

DESHUMIFICADOR

4. The applicable operating temperature range for

this unit is 5-35°C.

5. If the dehumidifier can’t start (the indicating

light does not illuminate) or the dehumidifier shut

down unreasonably, please make sure whether the

plug is connected firmly to power supply. If the

plug and power supply are in normal condition,

please wait for 10 minutes before restart the unit

(because it takes 10 minutes to reposition). If the

unit still does not start after 10 minutes, please

ask your local distributor service station to repair.

6. When the dehumidifier is operating, it’s a normal

situation that the working compressor may cause

some heat and bring the ambient temperature up.

7. When the product is defrosting, the related

indicating light will illuminate.

8. The unit shows the ambient humidity when it’s

operating. If the ambient humidity is higher than

RH95%, the display shows “HI”; if the ambient humidi-

ty is lower than RH35%, the display shows “LO”

9. Pls face to the front of the unit and lift it when

move the machine (as fig a.)

DRAINING INSTRUCTION

CONTINUOUS DRAINAGE

1. Before continuous

draining water, please take

out the water tank and plug

a draining tube to draining

hole (See Fig 02.) Then put

the water tank back.

2. Draining tube should

place lower than the

draining hole to let water flow out.

FILTER REMOVAL

1. Take out the water tank

before remove the filter.

2. Pulling out the filter with

handles of filter.

3. Wash the filter with cool

water (cooler than 40°C)

every two weeks, and put

filter back after it air-dried naturally.

MAINTENANCE INSTRUCTION

1. The unit is not allowed to be placed on surface

which is soft or not flat to avoid the unit cause

noise, vibration, and water or electricity leakage

when operating.

2. Never insert any slim rod or hard stuff into the

unit to avoid the damage of the unit.

3. Please disconnect the power cord to the power

supply when you turn off the unit or intend to stop

using for long time.

4. In order to improve the performance of dehumidi-

fier, please keep the unit in open place away from

barriers which may block the air.

5. Please wash the filter with cool water (cooler

than 40°C) but not gasoline or alcohol every two

weeks, and put filter back after it air-dried naturally.

1. Take out the water tank as Fig 01 and pour out

the water

2. Put the water tank back.

3. Press power key to turn on the unit.

Ref. 636134

DEHUMIDIFIER

DESHUMIFICADOR

Draining water can storage in the water tank, or

be continuous drained by PVC tube. (The PVC

tube is not included in the product.)

USAGE OF WATER TANK

When dehumidifying, the condensing water may

be drained to water tank. And the unit will stop

working with indicating light illuminates when the

water tank is full of water, please pour out the

water that time.

1. INFORMATION ON SERVICING

1) Checks to the area: Prior to beginning work on

systems containing flammable refrigerants, safety

checks are necessary to ensure that the risk of

ignition is minimised. For repair to the refrigerating

system, the following precautions shall be

complied with prior to conducting work on the

system.

2) Work procedure: Work shall be undertaken under

a controlled procedure so as to minimise the risk

of a flammable gas or vapour being present while

the: work is being performed.

3) Checking for presence of refrigerant: The area

shall be checked with an appropriate refrigerant

detector prior to and during work, to ensure the

technician is aware of potentially flammable

atmospheres. Ensure that the leak detection

equipment being used is suitable for use with

flammable refrigerants, i.e. non-sparking,

adequately sealed or intrinsically safe.

4) Presence of fire extinguisher: If any hot work is

to be conducted on the refrigeration equipment or

any associated parts, appropriate fire extinguish-

ing equipment shall be available to hand. Have a

dry powder or CO2 fire extinguisher adjacent to the

charging area.

5) No ignition sources: No person carrying out work

in relation to a refrigeration system which involves

exposing any pipe work that contains or has

contained flammable refrigerant shall use any

sources of ignition in such a manner that it may

lead to the risk of fire or explosion. All possible

ignition sources, including cigarette smoking,

should be kept sufficiently far away from the site

of installation, repairing, removing and disposal,

during which flammable refrigerant can possibly

be released to the surrounding space. Prior to work

taking place, the area around the equipment is to

be surveyed to make sure that there are no flamma-

ble hazards or ignition risks. “No Smoking” signs

shall be displayed.

6) Ventilated area: Ensure that the area is in the open

or that it is adequately ventilated before breaking

into the system or conducting any hot work. A

degree of ventilation shall continue during the

period that the work is carried out. The ventilation

should safely disperse any released refrigerant and

preferably expel it externally into the atmosphere.

7) Checks to the refrigeration equipment: Where

electrical components are being changed, they shall

be fit for the purpose and to the correct specifica-

tion. At all times the manufacturer’s maintenance

and service guidelines shall be followed. If in doubt

consult the manufacturer’s technical department for

assistance. The following checks shall be applied to

installations using flammable refrigerants:

– The charge size is in accordance with the room

size within which the refrigerant containing parts

are installed;

– The ventilation machinery and outlets are operat-

ing adequately and are not obstructed;

– If an indirect refrigerating circuit is being used, the

secondary circuit shall be checked for the presence

of refrigerant;

– Marking to the equipment continues to be visible

and legible. Markings and signs that are illegible

shall be corrected;

– Refrigeration pipe or components are installed in

a position where they are unlikely to be exposed to

any substance which may corrode refrigerant

containing components, unless the components are

constructed of materials which are inherently

resistant to being corroded or are suitably protected

atgainst being so corroded.

8) Checks to electrical devices: Repair and mainte-

nance to electrical components shall include initial

safety checks and component inspection

procedures. If a fault exists that could compromise

safety, then no electrical supply shall be connected

to the circuit until it is ºsatisfactorily dealt with. If

the fault cannot be corrected immediately but it is

necessary to continue operation, an adequate

temporary solution shall be used. This shall be

reported to the owner of the equipment so all

parties are advised. Initial safety checks shall

include:

• That capacitors are discharged: this shall be done

Troubleshooting

Ref. 636134

DEHUMIDIFIER

DESHUMIFICADOR

in a safe manner to avoid possibility of sparking –

That there no live electrical components and

wiring are exposed while charging, recovering or

purging the system– That there is continuity of

earth bonding.

2. REPAIRS TO SEALED COMPONENTS

1) During repairs to sealed components, all electri-

cal supplies shall be disconnected from the

equipment being worked upon prior to any removal

of sealed covers, etc. If it isabsolutely. necessary

to have an electrical supply to equipment during

servicing, then a permanently operating form of

leak detection shall be located at the most critical

point to warn of a potentially hazardous situation.

2) Particular attention shall be paid to the follow-

ing to ensure that by working on electrical compo-

nents, the casing is not altered in such a way that

the level of protection is affected. This shall

include damage to cables, excessive number of

connections, terminals not made to original

specification, damage to seals, incorrect fitting of

glands, etc. Ensure that apparatus is mounted

securely. Ensure that seals or sealing materials

have not degraded such that they no longer serve

the purpose of preventing the ingress of flamma-

ble atmospheres. Replacement parts shall be in

accordance with the manufacturer’s specifica-

tions.

NOTE: The use of silicon sealant may inhibit the

effectiveness of some types of leak detection

equipment. Intrinsically safe components do not

have to be isolated prior to working on them.

3. REPAIR TO INTRINSICALLY SAFE COMPO-

NENTS

Do not apply any permanent inductive or capaci-

tance loads to the circuit without ensuring that this

will not exceed the permissible voltage and current

permitted for the equipment in use. Intrinsically

safe components are the only types that can be

worked on while live in the presence of a flamma-

ble atmosphere. The test apparatus shall be at the

correct rating. Replace components only with

parts specified by the manufacturer. Other parts

may result in the ignition of refrigerant in the

atmosphere from a leak.

4. CABLING

Check that cabling will not be subject to wear,

corrosion, excessive pressure, vibration, sharp

edges or any other adverse environmental effects.

The check shall also take into account the effects

of aging or continual vibration from sources such as

compressors or fans.

5. DETECTION OF FLAMMABLE REFRIGERANTS

Under no circumstances shall potential sources of

ignition be used in the searching for or detection of

refrigerant leaks. A halide torch (or any other

detector using a naked flame) shall not be used.

6. LEAK DETECTION METHODS

The following leak detection methods are deemed

acceptable for systems containing flammable

refrigerants. Electronic leak detectors shall be used

to detect flammable refrigerants, but the sensitivity

may not be adequate, or may need re-calibration.

(Detection equipment shall be calibrated in a

refrigerant-free area.) Ensure that the detector is not

a potential source of ignition and is suitable for the

refrigerant used. Leak detection equipment shall be

set at a percentage of the LFL of the refrigerant and

shall be calibrated to the refrigerant employed and

the appropriate percentage of gas (25 % maximum)

is confirmed. Leak detection fluids are suitable for

use with most refrigerants but the use of detergents

containing chlorine shall be avoided as the chlorine

may react with the refrigerant and corrode the

copper pipe-work. If a leak is suspected, all naked

flames shall be removed/ extinguished. If a leakage

of refrigerant is found which requires brazing, all of

the refrigerant shall be recovered from the system,

or isolated (by means of shut off valves) in a part of

the system remote from the leak. Oxygen free

nitrogen (OFN) shall then be purged through the

system both before and during the brazing process.

7. REMOVAL AND EVACUATION

When breaking into the refrigerant circuit to make

repairs – or for any other purpose – conventional

procedures shall be used. However, it is important

that best practice is followed since flammability is a

consideration. The following procedure shall be

adhered to:

• Remove refrigerant – Purge the circuit with inert

gas – Evacuate – Purge again with inert gas – Open

the circuit by cutting or brazing.

The refrigerant charge shall be recovered into the

correct recovery cylinders. The system shall be

“flushed” with OFN to render the unit safe. This

process may need to be repeated several times.

Compressed air or oxygen shall not be used for this

task. Flushing shall be achieved by breaking the

vacuum in the system with OFN and continuing to

fill until the working pressure is achieved, then

Ref. 636134

DEHUMIDIFIER

DESHUMIFICADOR

venting to atmosphere, and finally pulling down to

a vacuum. This process shall be repeated until no

refrigerant is within the system. When the final

OFN charge is used, the system shal be vented

down to atmospheric pressure to enable work to

take place. This operation is absolutely vital if

brazing operations on the pipe-work are to take

place. Ensure that the outlet for the vacuum pump

is not close to any ignition sources and there is

ventilation available.

8. CHARGING PROCEDURES

In addition to conventional charging procedures,

the following requirements shall be followed.

– Ensure that contamination of different refriger-

ants does not occur when using charging

equipment. Hoses or lines shall be as short as

possible to minimise the amount of refrigerant

contained in them.

– Cylinders shall be kept upright.

– Ensure that the refrigeration system is earthed

prior to charging the system with refrigerant.

– Label the system when charging is complete (if

not already).

– Extreme care shall be taken not to overfill the

refrigeration system. Prior to recharging the

system it shall be pressure tested with OFN. The

system shall be leak tested on completion of

charging but prior to commissioning. A follow up

leak test shall be carried out prior to leaving the

site.

9. DECOMMISSIONING

Before carrying out this procedure, it is essential

that the technician is completely familiar with the

equipment and all its detail. It is recommended

good practice that all refrigerants are recovered

safely. Prior to the task being carried out, an oil

and refrigerant sample shall be taken in case

analysis is required prior to re-use of reclaimed

refrigerant. It is essential that electrical power is

available before the task is commenced.

a) Become familiar with the equipment and its

operation.

b) Isolate system electrically.

c) Before attempting the procedure ensure that:

• Mechanical handling equipment is available, if

required, for handling refrigerant cylinders;

• All personal protective equipment is available and

being used correctly;

• The recovery process is supervised at all times by

a competent person;

• Recovery equipment and cylinders conform to the

appropriate standards.

d) Pump down refrigerant system, if possible.

e) If a vacuum is not possible, make a manifold so

that refrigerant can be removed from

various parts of the system.

f) Make sure that cylinder is situated on the scales

before recovery takes place.

g) Start the recovery machine and operate in

accordance with manufacturer's instructions.

h) Do not overfill cylinders. (No more than 80 %

volume liquid charge).

i) Do not exceed the maximum working pressure of

the cylinder, even temporarily.

j) When the cylinders have been filled correctly and

the process completed, make sure that the cylinders

and the equipment are removed from site promptly

and all isolation valves on the equipment are closed

off.

k) Recovered refrigerant shall not be charged into

another refrigeration system unless it has been

cleaned and checked.

10. LABELLING

Equipment shall be labelled stating that it has been

de-commissioned and emptied of refrigerant. The

label shall be dated and signed. Ensure that there

are labels on the equipment stating the equipment

contains flammable refrigerant.

11. RECOVERY

When removing refrigerant from a system, either for

servicing or decommissioning, it is recommended

good practice that all refrigerants are removed

safely.

When transferring refrigerant into cylinders, ensure

that only appropriate refrigeran recovery cylinders

are employed. Ensure that the correct number of

cylinders for holding the total system charge is

available. All cylinders to be used are designated for

the recovered refrigerant and labelled for that

refrigerant (i.e. special cylinders for the recovery of

refrigerant). Cylinders shall be complete with

Ref. 636134

DEHUMIDIFIER

DESHUMIFICADOR

pressure relief valve and associated shut-off

valves in good working order. Empty recovery

cylinders are evacuated and, if possible, cooled

before recovery occurs. The recovery equipment

shall be in good working order with a set of instruc-

tions concerning the equipment that is at hand and

shall be suitable for the recovery of flammable

refrigerants. In addition, a set of calibrated weigh-

ing scales shall be available and in good working

order. Hoses shall be complete with leak-free

disconnect couplings and in good condition.

Before using the recovery machine, check that it is

in satisfactory working order, has been properly

maintained and that any associated electrical

components are sealed to prevent ignition in the

event of a refrigerant release. Consult manufactur-

er if in doubt.

The recovered refrigerant shall be returned to the

refrigerant supplier in the correct recovery cylinder,

and the relevant Waste Transfer Note arranged. Do

not mix refrigerants in recovery units and especial-

ly not in cylinders.

If compressors or compressor oils are to be

removed, ensure that they have been evacuated to

an acceptable level to make certain that flamma-

ble refrigerant does not remain within the

lubricant. The evacuation process shall be carried

out prior to returning the compressor to the suppli-

ers. Only electric heating to the compressor body

shall be employed to accelerate this process.

When oil is drained from a system, it shall be

carried out safely.

Fuse parameters of the machine

Type: 5H or 524 Voltage: 250V Current: 3.15 A

PERMISSIBLE EXCESSIVE OPERATING PRESSURE

Suction.........................................................................................................................0.6MPa(6Kgf/cm2)

Discharge...................................................................................................................2.5MPa(25Kgf/cm2)

Maximum Operation Pressure................................................................................................4.0MPa(40Kgf/cm2)

Dimension (W x D x H ) mm.......................................................................................................360Wx246Dx506H

Applicable temperature..........................................................................................................................5°C-35°C

Water Tank Capacity.....................................................................................................................................3.2 L

SPECIFICATIONS

Power Supply

Power Input

Moisture Removal

Refrigerant

Model REF 636134

(30°C RH80%)

220-240V~50Hz

365 W

30 liters/day

R290, 0.13kg

Ref. 636134

DEHUMIDIFIER

DESHUMIFICADOR

TRANSPORTATION, MARKING AND STORAGE FOR UNITS

1. Transport of equipment containing flammable refrigerants.

Compliance with the transport regulations.

2. Markingofequipmentusingsigns.Compliancewithlocalregulations.

3. Disposal of equipment using flammable refrigerants.

Compliance with national regulations.

4. Storage of equipment/appliances. The storage of

equipment should be in accordance with the manufacturer’s

instructions.

5. Storage of packed (unsold) equipment. Storage package

protection should be constructed such that mechanical

damage to the equipment inside the package will not cause a

leak of the refrigerant charge. The maximum number of

pieces of equipment permitted to be stored together will be

determined by local regulations.

6. The appliance shall be stored so as to prevent mechanical

damage from occurring.

7. General work area. All maintenance staff and others

working in the local area shall be instructed on the nature of

work being carried out. Work in confined spaces shall be

avoided. The area around the workspace shall be sectioned

off. Ensure that the conditions within the area have been

made safe by control of flammable material.

This marking indicates that this product should not be disposed with other household

wastes throughout the EU.

To prevent possible hazards to the environment or human health from uncontrolled waste

disposal, please recycle it to prove the sustainable reuse of material resources. Please ask

return and collection systems or contact the retailer where the product was purchased to

return your used device, they can recycle products safely.

DESHUMIDIFICADOR

DEHUMIDIFIER

1.No utilice medios para acelerar la descongelación ni para

limpiar que no sean los recomendados por e fabricante

2.El electrodoméstico se debe almacenar en una estancia

donde no haya fuentes de ignición activas continuamente

(por ejemplo: llamas expuestas, aparatos de gas en funciona-

miento o calefactores eléctricos encendidos).

3.No debe perforarse ni quemarse.

4.Tenga en cuenta que algunos refrigerantes son inodoros.

5. El aparato se instalará, operará y almacenará en una

habitación con una superficie superior a 12m2.

6.Las reparaciones solo se llevarán a cabo del modo

recomendado por el fabricante.

7.El electrodoméstico debe almacenarse en una zona con

buena ventilación, y el tamaño de la habitación se debe

corresponder con el tamaño especificado para la sala donde

se vaya a utilizar

8.Los procedimientos de trabajo que afecten a las medidas

de seguridad deberán llevarlos a cabo las personas

competentes.

9.Lea el manual atentamente antes de utilizar este producto

por primera vez y almacene la unidad en un lugar seguro

para evitar fugas eléctricas, combustión o lesiones.

10.No sumerja este producto en agua ni en ningún otro

líquido.

11. Si el cable de alimentación está dañado, debe ser

reemplazado por el fabricante, su agente de servicio técnico

u otro personal cualificado a fin de prevenir riesgos.

12.Solicite la asistencia de un servicio técnico profesional

para reparar el producto. Una reparación inapropiada podría

causar daños a los usuarios.

13.Desconecte el electrodoméstico de la fuente de

alimentación antes de moverlo o limpiarlo, y también cuando

el producto no se utilice.

14.Utilice el producto con la tensión eléctrica especificada.

15.Utilice este producto exclusivamente como electrodomésti-

co y siga el propósito previsto.

16.No ponga nada encima del producto.

17.Para evitar fugas de agua, limpie el depósito de agua antes

de mover el producto.

18.No incline el producto, pues pueden producirse fugas de

agua que lo dañen.

19.Este electrodoméstico lo pueden usar los niños a partir de 8

años y personas con las capacidades físicas, sensoriales o

mentales reducidas, así como aquellas con falta de experien-

cia o conocimiento, siempre que hayan sido supervisadas o

formadas en cuanto al uso del electrodoméstico de forma

segura y sean conscientes de los riesgos asociados. Los niños

no deben jugar con el electrodoméstico. Los niños no deben

limpiar el producto ni realizar tareas de mantenimiento sin

supervisión.

20.Mantenga el producto a una distancia mínima de 50cm de

la pared u otros obstáculos.

21.El electrodoméstico debe instalarse de conformidad con las

normas nacionales sobre instalaciones eléctricas.

22.La temperatura de funcionamiento aplicable para esta

unidad es de 5 a 35°C.

23.No utilice el deshumidificador en estancias húmedas,

como cuartos de baño o lavaderos.

24 Las tuberías de refrigerante deben cumplir con los

reglamentos nacionales de gas.

INFORMACIÓN DE SEGURIDAD

1. PANEL DE CONTROL

2. SALIDA DE AIRE

3. ASIDERO

4. ARMAZÓN DELANTERO

5. ENTRADA DE AIRE/

ARMAZÓN TRASERO

6. ORIFICIO DE DRENAJE

7. DEPÓSITO DE AGUA

Ref.636134

INSTRUCCIONES

DE USO

DESHUMIDIFICADOR

DEHUMIDIFIER

1. ENCENDIDO/APAGADO

Pulse esta tecla para encender y apagar; la luz

indicadora correspondiente se iluminará o apagará

respectivamente. (Mientras se esté descongelan-

do la unidad, la luz indicadora se encenderá y

apagará de manera intermitente).

2. VELOCIDAD DEL VENTILADOR

Pulse esta tecla para seleccionar velocidad alta

(HI) o baja (LOW); la luz indicadora correspondi-

ente se encenderá o apagará.

3. TEMPORIZADOR

a. Pulse esta tecla para ajustar el tiempo que

necesite (de 1 a 24 horas).

b. Cuando ajuste el temporizador en modo de

espera, la unidad se encenderá automáticamente;

cuando ajuste el temporizador en modo de funcio-

namiento, la unidad se apagará automáticamente.

c. Si pulsa la tecla de encendido para apagar la

unidad antes de que termine el tiempo de la cuenta

atrás, se cancelará el ajuste del temporizador.

d. Mientras el temporizador está en uso, la luz

indicadora se ilumina; si no, la luz se apaga.

e. Después de ajustar el temporizador a 5segun-

dos, la pantalla P3 vuelve a mostrar la humedad

ambiental. (Vuelva a pulsar para que se muestre el

tiempo de apagado).

4. AJUSTE DE LA HUMEDAD

Pulse esta tecla para ajustar la humedad relativa

que necesite. (De deshumidificación continuada

[CO] a humedad relativa 50, 60, 70 u 80%, modo de

confort [AU] y otra vez a deshumidificación contin-

uada [CO]. La primera vez que la encienda, la

unidad está configurada en el modo de deshumidi-

ficación continuada [CO].

Cuando la humedad ambiental sea un 3% inferior a

la humedad configurada, el compresor se detiene de

forma automática y vuelve a ponerse en funciona-

miento cuando la humedad ambiental es un 3 %

superior a la humedad configurada.

MODO DE CONFORT [AU]

a. Cuando la temperatura ambiente sea inferior a 5

°C, el compresor dejará de funcionar.

b. Cuando la temperatura ambiente sea superior a 5

°C e inferior a 20 °C, el producto establecerá

automáticamente una humedad del 60%.

c. Cuando la temperatura ambiente sea superior a

20 °C e inferior a 27 °C, el producto establecerá

automáticamente una humedad del 55%.

d. Cuando la temperatura ambiente sea superior a

27°C, el producto establecerá automáticamente una

humedad del 50%.

DEPÓSITO DE AGUA LLENO

Cuando el depósito de agua esté lleno, la luz indica-

dora se iluminará y la unidad dejará de funcionar

hasta que se vacíe el depósito.

DESCONGELACIÓN

Cuando se esté descongelando la unidad, la luz

indicadora se iluminará y el compresor dejará de

funcionar, pero el motor se mantendrá en funciona-

miento.

ADVERTENCIA

1. Cuando utilice el deshumidificador, no establezca

la humedad a un nivel más alto que la humedad

ambiental.

DESCRIPCIÓN DEL PANEL DE CONTROL

INSTRUCCIONES DE USO

Ref.636134

Inhaltsverzeichnis

Sprachen:

Andere VDL Luftentfeuchter Handbücher

VDL

VDL PD50-HAE Bedienungsanleitung

Beliebte Luftentfeuchter Handbücher anderer Marken

Daitsu

Daitsu CD031IU-DFA Bedienungsanleitung

Fehom

Fehom PDGT701BE Bedienungsanleitung

Hitachi

Hitachi RD-190GX Bedienungsanleitung

Westpoint

Westpoint MDF1-30AE Bedienungsanleitung

SOLIS

SOLIS easy dry compact Bedienungsanleitung

Sinclair

Sinclair R-9112 Bedienungsanleitung

Kenmore

Kenmore 580.54701 Bedienungsanleitung

Demargo

Demargo DM828NF Bedienungsanleitung

Altrad Lescha

Altrad Lescha LDH 600 Bedienungsanleitung

BOMANN

BOMANN LE 1150 CB Bedienungsanleitung

SPT

SPT SD-46 Bedienungsanleitung

REMKO

REMKO SLN 40 Bedienungsanleitung

Haier

Haier HD458 Bedienungsanleitung

Logik

Logik L20DHW12 Bedienungsanleitung

Frigidaire

Frigidaire FDR30S1 - 30 Pint Capacity Dehumidifier Kurzanleitung

Blitz

Blitz HHD Series Bedienungsanleitung

Prem-I-Air

Prem-I-Air PD14DEN Bedienungsanleitung

Klarstein

Klarstein 10032042 Bedienungsanleitung