veise KS02A Bedienungsanleitung
KS02A
Keypad Digital Deadbolt
Installation Guide / Programming Instructions
Thank you for purchasing our products. Please review this manual thoroughly before operating your device.
All pictures in this manual are for illustration purpose only. Actual product may vary due to product upgrade.
Installation Overview Programming Instructions
STEP 1: Prepare the door and check dimensions
STEP 2: Install the latch and strike
STEP 3: Install exterior assembly
STEP 4: Install interior assembly
STEP 5: Detect left/right hand door installation
P 3
P 4
P 6
P 7
P 8
P 9
P10
P 11
P 12
P 13
At a Glance
How to Use
Definitions
Code Format
Quick Set Up
P 15
P16
P17
Factory Default Settings
Troubleshooting
Information & Safety Warnings
IMPORTANT:
TOOL REQUIRED:
Do not use an electric
screwdriver during installation.
Do not load batteries until lock is
completely installed.
INSTALLATION OVERVIEW
1
Strike Screws
(H)
Interior Assembly
Screws (K)
Strike (D)
Backup key (A)
Mounting
plate Screws (J)
Battery
Cover (G)
Mounting
plate (E)
Interior
Assembly (F)
Exterior Assembly
(B)
Latch (C)
Latch Screws
(I)
Reinforcement
plate (D-1)
Latch x1
Drive-In Collar (Optional)
Strike x1
Exterior Assembly x1
Mounting Plate x1 Interior Assembly x1 Battery Cover x1 Strike Screws x4
Mounting plate Screws x2 Interior Assembly
Screws x3
Latch Screws x2
A B C
E F G
L
H
I
J K
D
Reset Tool x1 M
Parts List
If any parts are missing or damaged, please contact Customer Support.
2
Backup Key x2
Reinforcement
Plate x1
(optional)
Measure to confirm
that the hole in the
door edge is 1"
(25mm).
Measure to confirm
that the backset is
either 2-3/8" or
2-3/4" (60 or 70mm)
2-3/8" or 2-3/4"
(60 or 70mm)
Make sure the hole in
door frame is drilled a
minimum of 1"
(25mm) deep.
Measure to confirm
that the door is 1-3/8"
to 2" (35 mm or
50mm) thick.
A
Measure to
confirm that the
hole in the door is
2-1/8" (54mm).
B
CD
Prepare the door and check dimensions
1
STEP
3
1"
25mm
1-3/8" to 2"
(35mm or 50mm)
4
chiseled
not chiseled
Drive-In Collar
(B)
Install the latch and strike
2
STEP
Hold the latch in front of the door hole,
with the latch face flush against the
door edge. Is the slotted hole centered
in the door hole?
No adjustment is required.
Proceed to next step.
Slotted hole is
NOT centered.
A
B
YES
NO
Rotate and pull the
latch as shown to
extend latch.
2-3/4"
(70mm)
2-3/8"
(60mm)
pull
Determine backset
and adjust the latch
Install the latch
Latch Screws (I)
up
CUse a screwdriver to test if
deadbolt works smoothly.
DInstall strike on the door frame. Make sure the hole in door frame is
drilled a minimum of 1" (25mm)
deep.
IMPORTANT:
5
D
(Optional)
AB
Mounting plate Screws(J)
Keep parallel to
door edge.
Install exterior assembly
3
STEP
Unlocked
Before installation, make sure the latch is
fully retracted (in the unlocked position)
IMPORTANT:
Locked
With the latch fully retracted (in the unlocked
position), route the cable below the latch, and
insert the tourque blade through the slot in the
latch. 6
Tourque
blade
Secure the mounting plate with the
supplied screws. Do not overtighten
screws.
C
Unlocked
Keep the thumb turn in vertical position and install
the interior assembly.
Install interior assembly
4
STEP
Do not load batteries until lock is
completely installed.
IMPORTANT:
Push the battery cover out in
the direction as illustrated.
Insert the cable
connector to the
socket. Push the
connector in firmly
until it is completely
attached.
Attach Interior
Assembly to
Mounting Plate and
tighten 3 Screws.
A B
D
7
Horizontal
Interior Assembly
Screws (K)
While the door is OPEN and
UNLOCKED, load 3 AA batteries
into the battery compartment.
Note:
For long last, please use all new,
non-rechargeable Alkaline
batteries only.
Press and hold the Reset button on
the interior assembly by using the
reset tool.
This step is required and crucial for the lock
to operate properly.
IMPORTANT:
Detect left/right hand door installation
5
STEP
Reset the lock to teach the lock the orientation of the door.
A B Load the 4th battery and keep holding
the reset button for 3 seconds, until
you hear the sound of "beep". The
latch bolt will extend to learn the
orientation of the door automatically.
C
8
Reset button
Unlocked
Inhaltsverzeichnis
Andere veise Sperren Handbücher
