Velleman POWER BLOCK K8081 Bedienungsanleitung

Total solder points: 383

Difficulty level: beginner 123 4 5⌧advanced

POWERBLOCK - POWER AMPLIFIER

ILLUSTRATED ASSEMBLY MANUAL H8081IP-1

Thisamplifierisanidealset-upforactivespeakeruse.

K8081

Features & specifications

This power amplifier is an ideal set-up for active speaker use.

Build a high-quality system, using two (stereo) or more (surround) amplifiers.

Due to its auto switch-on, through input signal sensing, the unit can be installed

at almost any place.

Comes complete with enclosure and transformer.

Features :

 fully discrete design using Epitaxial Darlington transistors

 includes all connectors, transformer and enclosure

 overload and short-circuit protection

 DC error protection with LED indication

 automatic switch-on upon input signal sensing (automatic switch-off)

Specifications

• 200W music power @ 4 ohm load

• 100W rms power @ 4 ohm load @ 10%THD

• distortion: 0.02% @ 1KHz/10W

• damping factor: >800

• frequency response: 3Hz to 200KHz (-3dB)

• sensitivity: 0.6V rms

• signal to noise ratio: 115dB

• power supply: 235 or 115 Vac

• Auto sensing on time : 15min.

• dimensions: 195 x 180 x 60mm (7.7" x 7" x 2.4")

Assembly hints

1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project

successful. Read them carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a

small tip.

• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to

the tip, to give it a wet look. This is called ‘thinning’ and will protect

the tip, and enables you to make good connections. When solder

rolls off the tip, it needs cleaning.

• Thin raisin-core solder. Do not use any flux or grease.

• A diagonal cutter to trim excess wires. To avoid injury when cutting

excess leads, hold the lead so they cannot fly towards the eyes.

• Needle nose pliers, for bending leads, or to hold compo-

nents in place.

• Small blade and Phillips screwdrivers. A basic range

is fine.

For some projects, a basic multi-meter is required, or might

be handy

1.2 Assembly Hints :

⇒Make sure the skill level matches your experience, to avoid disappointments.

⇒Follow the instructions carefully. Read and understand the entire step before

you perform each operation.

⇒Perform the assembly in the correct order as stated in this manual

⇒Position all parts on the PCB (Printed Circuit Board) as shown on the draw-

ings.

⇒Values on the circuit diagram are subject to changes.

⇒Values in this assembly guide are correct*

0.000

⇒Use the check-boxes to mark your progress.

⇒Please read the included information on safety and customer service

* Typographical inaccuracies excluded. Always look for possible last minute

manual updates, indicated as ‘NOTE’ on a separate leaflet.

1.3 Soldering Hints :

1- Mount the component against the PCB sur-

face and carefully solder the leads

2- Make sure the solder joints are cone-shaped

and shiny

3- Trim excess leads as close as possible to the

solder joint

REMOVE THEM FROM THE TAPE ONE AT

A TIME !

Assembly hints

AXIAL COMPONENTS ARE TAPED IN

THE CORRECT MOUNTING SEQUENCE !

Construction

 R1 : 330 (3 - 3 - 1 - B)

 R2 : 220 (2 - 2 - 1 - B)

 R3 : 47 (4 - 7 - 0 - B)

 R4 : 3K3 (3 - 3 - 2 - B)

 R5 : 100 (1 - 0 - 1 - B)

 R6 : 22K (2 - 2 - 3 - B)

 R7 : 120 (1 - 2 - 1 - B)

 R8 : 2K2 (2 - 2 - 2 - B)

 R9 : 680 (6 - 8 - 1 - B)

 R10 : 3K3 (3 - 3 - 2 - B)

 R11 : 3K3 (3 - 3 - 2 - B)

 R12 : 10 (1 - 0 - 0 - B)

 R13 : 18K (1 - 8 - 3 - B - 9)

 R14 : 2K7 (2 - 7 - 2 - B - 9)

 R15 : 1K5 (1 - 5 - 2 - B)

 R16 : 47 (4 - 7 - 0 - B)

 R17 : 3K3 (3 - 3 - 2 - B)

 R18 : 680 (6 - 8 - 1 - B)

 R19 : 1K (1 - 0 - 2 - B)

 R20 : 220 (2 - 2 - 1 - B)

 R21 : 470 (4 - 7 - 1 - B)

 R22 : 470K (4 - 7 - 4 - B)

 R23 : 100K (1 - 0 - 4 - B)

 R24 : 1K (1 - 0 - 2 - B)

 R25 : 1M (1 - 0 - 5 - B)

 R26 : 470K (4 - 7 - 4 - B)

 R27 : 100 (1 - 0 - 1 - B)

 R28 : 15K (1 - 5 - 3 - B)

 R29 : 470K (4 - 7 - 4 - B)

 R30 : 100K (1 - 0 - 4 - B)

 R31 : 47K (4 - 7 - 3 - B)

 R32 : 2K7 (2 - 7 - 2 - B - 9)

4. 1/4W resistors.

R...

 J

1. Jump wires.

 D1 : 1N4148

 D2 : 1N4148

 D3 : 1N4148

 D4 : 1N4148

 D5 : 1N4148

 D6 : 1N4148

 D7 : 1N4148

 D8 : 1N4148

 D9 : 1N4007

 D10 : 1N4007

Mounting Diode D11 :

 D11 : 1N4007

 Mount D11.

2. Diodes (check the polarity)

CATHODE

D...

 ZD1 : 5V1

 ZD2 : 9V1

3. Zener diodes (check the polarity)

CATHODE

ZD...

Construction

 IC1 : 8p

 IC2 : 8p

 IC3 : 6p

5. IC sockets. Watch the position

of the notch!

 RV1 : 1K

Bias adjustment

6. Trim potentiometer

 T1 : BC640

 T2 : BC640

 T3 : BC639

 T4 : BC547

 T5 : BC557

 T6 : BC547

 T7 : BC547

8. Transistors

 Make sure that transistor T7 is

bent towards diode D11.

 Make sure that the transistor and

diode leads do not touch each

other.

 C1 : 47pF (47)

 C2 : 47pF (47)

 C3 : 1nF (102)

 C4 : 680pF (680)

 C5 : 680pF (680)

 C6 : 10nF (103)

 C7 : 10nF (103)

 C8 : 47nF (473)

 C9 : 100nF (104)

 C10 : 100nF (104)

 C11 : 100nF (104)

 C12 : 100nF (104)

7. Capacitors

c...

 R33 : 3K3 (3 - 3 - 2 - B)

 R34 : 560 (5 - 6 - 1 - B - 9)

 R35 : 10K (1 - 0 - 3 - B)

 R36 : 47K (4 - 7 - 3 - B)

 R37 : 1K (1 - 0 - 2 - B)

 R38 : 10K (1 - 0 - 3 - B)

 R39 : 1K (1 - 0 - 2 - B)

 R40 : 2K2 (2 - 2 - 2 - B)

 R41 : 10K (1 - 0 - 3 - B)

 LD4 : Power (red)

9. LEDs. Watch the polarity!

LD1

CATHODE

Construction

 GND : 1 pin

 TEST : 1 pin

 +40V : 1 pin

 T8 : 6 pins

 T9 : 6 pins

10. Pinheaders

 R42 : 0,47

 R43 : 0,47

12. 5W resistors

R...

2mm

 LS+

 LS-

 AC RED

 AC GREY

 AC YELLOW

 AC BLUE

13. Flat receptacles

SK...

 SK5 : IN

11. Male board wire connector

 LD1 : yellow (standby)

 LD2 : Blue (on)

 LD3 : red (check)

CATHODE

IMPORTANT

Mount these LED's exactly like in the

drawing, otherwise some LED's will

not fit correctly in the front panel.

 C13 : 10µF

 C14 : 10µF

 C15 : 10µF

 C16 : 47µF / 16V

 C17 : 100µF / 50V

 C18 : 100µF / 50V

 C19 : 220µF / 16V

 C20 : 220µF / 16V

 C21 : 220µF / 16V

 C22 : 470µF / 16V

14. Electrolytic capacitors.

Watch the polarity !

C...

7mm

CATHODE

+/-3mm

LD...

construction

Mount following diodes 15mm

above the PCB :

 D14 : 1N5404

 D15 : 1N5404

Mount following diodes 10mm

above the PCB :

 D12 : 1N5404

 D13 : 1N5404

15. Power diodes

(check the polarity)

CATHODE

D...

 RY1 : VR5V242C

( 24VDC - 5A - 2C)

16. Relay

 C23 : 3300µF / 50V

 C24 : 3300µF / 50V

17. Electrolytic capacitors.

Watch the polarity !

C...

Mount all 4 brackets,

fasten them using 6mm

M3 bolt + M3 nut

19.Brackets

brackets

 IC1 : LM258P

 IC2 : VK8081 (programmed PIC10F200-I/PG)

 IC3 : TIL111 or 4N27

18. IC's. Watch the position of the

notch!

20. ASSEMBLY OF THE UNIT

Assembly

• cut all connections to 1.5mm

 Make sure that the solder connections don't

touch the housing.

• fix rubber foot in center of PCB

Use the colour pictures on packaging as guideline

Max. 1.5mm

Inhaltsverzeichnis

Andere Velleman Verstärker Handbücher

Velleman

Velleman HQ Power PAA04 Bedienungsanleitung

Velleman

Velleman K1803 Bedienungsanleitung

Velleman

Velleman VPA2100M Bedienungsanleitung

Velleman

Velleman High-Q K2572 Bedienungsanleitung

Velleman

Velleman 8020 Bedienungsanleitung

Velleman

Velleman BTR4 Bedienungsanleitung

Velleman

Velleman HQ Power ONELINER 200 Bedienungsanleitung

Velleman

Velleman 8040 Bedienungsanleitung

Velleman

Velleman High-Q Kit K1803 Bedienungsanleitung

Velleman

Velleman HQ-POWER SAGIRA 100 Bedienungsanleitung

Velleman

Velleman K4040 Bedienungsanleitung

Velleman

Velleman K4003 Bedienungsanleitung

Velleman

Velleman VM100 Bedienungsanleitung

Velleman

Velleman HQ Power PAA01 Bedienungsanleitung

Velleman

Velleman HQ-Power ANTM7 Bedienungsanleitung

Velleman

Velleman 8021 Bedienungsanleitung

Velleman

Velleman K4020 Bedienungsanleitung

Velleman

Velleman HQ Power ONELINER 100 Bedienungsanleitung

Velleman

Velleman K8066 Bedienungsanleitung

Velleman

Velleman K4040 Bedienungsanleitung

Velleman

Velleman HQ Power VPA2200MBN Bedienungsanleitung

Velleman

Velleman HQ Power VPA2350MB Bedienungsanleitung

Velleman

Velleman VM113 Bedienungsanleitung

Velleman

Velleman High-Q Velleman-kit K8022 Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung