Velleman K8093 Bedienungsanleitung

ILLUSTRATED ASSEMBLY MANUAL H8093IP’1

K8093

Remote controlled

home alarm

��

Velleman N.V.

Legen Heirweg 33

9890 Gavere

(België)

��

Forum

Participate our Velleman Projects Forum

Subscribing our newsletter?, visit www.vellemanprojects.eu

��

assembly

hints 1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a small tip.

• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and

will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.

• Thinraisin-coresolder.Donotuseanyuxorgrease.

• Adiagonalcuttertotrimexcesswires.Toavoidinjurywhencuttingexcessleads,holdtheleadsotheycannot

ytowardstheeyes.

• Needle nose pliers, for bending leads, or to hold components in place.

• SmallbladeandPhillipsscrewdrivers.Abasicrangeisne.

)For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

• Makesuretheskilllevelmatchesyourexperience,toavoiddisappointments.

• Follow the instructions carefully. Read and understand the entire step before you perform each operation.

• Perform the assembly in the correct order as stated in this manual

• Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.

• Values on the circuit diagram are subject to changes, the values in this assembly guide are correct*

• Usethecheck-boxestomarkyourprogress.

• Please read the included information on safety and customer service

*Typographicalinaccuraciesexcluded.Alwayslookforpossiblelastminutemanualupdates,indicatedas‘NOTE’onaseparateleaet.

1.3 Soldering Hints :

1. Mount the component against the PCB surface and carefully solder the leads

2. Make sure the solder joints are cone-shaped and shiny

3. Trimexcessleadsascloseaspossibletothesolderjoint

- 5 -

- 4 -

DO NOT BLINDLY FOLLOW THE ORDER OF THE

COMPONENTS ONTO THE TAPE. ALWAYS CHECK THEIR

VALUE ON THE PARTS LIST!

��

assembly

hints 1. Assembly (Skipping this can lead to troubles ! )

Ok, so we have your attention. These hints will help you to make this project successful. Read them carefully.

1.1 Make sure you have the right tools:

• A good quality soldering iron (25-40W) with a small tip.

• Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the tip, to give it a wet look. This is called ‘thinning’ and

will protect the tip, and enables you to make good connections. When solder rolls off the tip, it needs cleaning.

• Thinraisin-coresolder.Donotuseanyuxorgrease.

• Adiagonalcuttertotrimexcesswires.Toavoidinjurywhencuttingexcessleads,holdtheleadsotheycannot

ytowardstheeyes.

• Needle nose pliers, for bending leads, or to hold components in place.

• SmallbladeandPhillipsscrewdrivers.Abasicrangeisne.

)For some projects, a basic multi-meter is required, or might be handy

1.2 Assembly Hints :

• Makesuretheskilllevelmatchesyourexperience,toavoiddisappointments.

• Follow the instructions carefully. Read and understand the entire step before you perform each operation.

• Perform the assembly in the correct order as stated in this manual

• Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.

• Values on the circuit diagram are subject to changes, the values in this assembly guide are correct*

• Usethecheck-boxestomarkyourprogress.

• Please read the included information on safety and customer service

*Typographicalinaccuraciesexcluded.Alwayslookforpossiblelastminutemanualupdates,indicatedas‘NOTE’onaseparateleaet.

1.3 Soldering Hints :

1. Mount the component against the PCB surface and carefully solder the leads

2. Make sure the solder joints are cone-shaped and shiny

3. Trimexcessleadsascloseaspossibletothesolderjoint

0.000

- 5 -

- 4 -

��

- 7 -

- 6 -

R1 : 47K (4 - 7 - 3 - B)

R2 : 560 (5 - 6 - 1 - B)

R3 : 560 (5 - 6 - 1 - B)

R4 : 47K (4 - 7 - 3 - B)

R5 : 560 (5 - 6 - 1 - B)

R6 : 1K (1 - 0 - 2 - B)

R7 : 10K (1 - 0 - 3 - B)

R8 : 10K (1 - 0 - 3 - B)

R9 : 2K2 (2 - 2 - 2 - B)

R10 : 560 (5 - 6 - 1 - B)

R...

I. CONSTRUCTION

features

• can store up to 4 remote controls (FIFO)

• chime function

• built-in pre-alarm

• always armed after power outage

• the built-in relay can switch a regular alarm (not included) (3 A 125 VAC) after 20 s pre-alarm

• arm time:

• slow with indication: if the door is open or closed (time to leave the room)

• quickly

• magnetic door contact included

Specications

• power supply: 12V DC

• consumption:

• armed: 20 mA

• alarm relay powered: 50 mA

• relay: 3 A - 125 VAC

• frequency: 433.92 MHz

• 32-bit code technology

• more than 1.000.000.000 unique codes

• code can easily be changed for safety purposes

• transmitter: R&TTE compliant (ETS 300-220) *

• openeldrangeofupto30mpossible

• external antenna wire

• receiver dimensions: 108 x 102 x 45 mm / 4.25 x 4 x 1.77"

* ETS 300 -220:only for EU countries

Compatible remotes (not included):

VM130T: 2-channel RF

remote control transmitter

VM166T: 2-channel

transmitter with LED light

��

- 7 -

- 6 -

Construction

R1 : 47K (4 - 7 - 3 - B)

R2 : 560 (5 - 6 - 1 - B)

R3 : 560 (5 - 6 - 1 - B)

R4 : 47K (4 - 7 - 3 - B)

R5 : 560 (5 - 6 - 1 - B)

R6 : 1K (1 - 0 - 2 - B)

R7 : 10K (1 - 0 - 3 - B)

R8 : 10K (1 - 0 - 3 - B)

R9 : 2K2 (2 - 2 - 2 - B)

R10 : 560 (5 - 6 - 1 - B)

Resistors

IC socket

R...

Ceramic Capacitors

C1 : 100nF (104)

C2 : 100nF (104)

C3 : 100nF (104)

IC1: 14p

...

Vertical diode

CATHODE

D...

CATHODE

D2 : 1N4007

Transistors

T1 : BC547

T2 : BC547

T3 : BC547

I. CONSTRUCTION

Diodes

D1 : 1N4148

D2 : 1N4148

Watch the

polarity!

Watch the

polarity!

TVoltage regulator

VR...VR...

VR1 : UA78L05

Push button

SW1:LEARN BUTTON

Watch the position of

the notch!

features

• can store up to 4 remote controls (FIFO)

• chime function

• built-in pre-alarm

• always armed after power outage

• the built-in relay can switch a regular alarm (not included) (3 A 125 VAC) after 20 s pre-alarm

• arm time:

• slow with indication: if the door is open or closed (time to leave the room)

• quickly

• magnetic door contact included

Specications

• power supply: 12V DC

• consumption:

• armed: 20 mA

• alarm relay powered: 50 mA

• relay: 3 A - 125 VAC

• frequency: 433.92 MHz

• 32-bit code technology

• more than 1.000.000.000 unique codes

• code can easily be changed for safety purposes

• transmitter: R&TTE compliant (ETS 300-220) *

• openeldrangeofupto30mpossible

• external antenna wire

• receiver dimensions: 108 x 102 x 45 mm / 4.25 x 4 x 1.77"

* ETS 300 -220:only for EU countries

��

- 8 - - 9 -

Construction

Sounder

BUZ1

BUZ1

Terminal blocks

SK2 : 2p (Relais)

SK3 : 2p (N.O. / N.C)

SK4 : 2p (COM / -)

SK5 : 2p (power supply)

Output

Electrolytic capacitors

Watch the polarity!

C4 : 470µF

C5 : 10µF

RF-receiver

RX1 : RX433N

Relay

LD1: Red (power)

LD2: Red (status)

LD3: Red (alarm)

LD4: Green (relais)

COM

NO NC

LED’s

STEP1: Place the LEDs together with the circuit board in the upper part

of the housing.

STEP2: Solder one lead of each led and check the positon. If OK,

solder the second lead.

R...

STEP1 STEP2

C (-)

Watch the polarity!

IC1: VK8093

(programmed PIC16F1503-I/P)

R...

RY1

��

- 8 - - 9 -

Assembly

Relay

LED’s

R...

STEP2

Watch the position of

the notch!

IC1: VK8093

(programmed PIC16F1503-I/P)

Antenna

R...

Home Alarm System with RF Remote

K8093

LEARN

TX 12V DC OUTPUT REED

NO NC COM

TOP

PCB

BOTTOM

SCREW

II. ASSEMBLY

��

- 10 - - 11 -

R...

Driver installation & programs

IV. ARMING THE UNIT

Out of the box no remotes are assigned for safety reasons. When the unit powers up it is always armed!

Unit is capable of storing 4 remotes, FIFO.

The stored remotes can be cleared from memory by holding the LEARN button while powering up, The unit will beep 10 times

(fast) to indicate the erasing process.

STATUS INDICATION (LD3)

LEARNING A REMOTE:

1. Press the “Learn”-button once, the status LED light continious. The unit is ready for learning a remote (there is a timeout!).

2. Hold the 2 buttons of the remote pressed. Release the buttons when the status LED turns off , the remote is learned.

REMOTE CONTROL:

1. DISARM

2. ARM

Power

supply

Relay

Door contact

GND*

(*) If you want to connect a 12V

siren directly to the relay you can

connect the +12V of the input volt-

age to the COM. Connect the nega-

tive lead of the siren to the leftmost

(-) connector and the positive to

the NC or NO contact of the relay.

III.CONNECTION DIAGRAM

��

Inhaltsverzeichnis

Andere Velleman Sicherheitssystem Handbücher

Velleman

Velleman CAMZWEXT3N Bedienungsanleitung

Velleman

Velleman CCTVPROM18 Bedienungsanleitung

Velleman

Velleman HAM220 Bedienungsanleitung

Velleman

Velleman CAMSET31 Bedienungsanleitung

Velleman

Velleman HAM221 Bedienungsanleitung

Velleman

Velleman CAMSETW1 Bedienungsanleitung

Velleman

Velleman PEM7D Bedienungsanleitung

Velleman

Velleman HAM201 Bedienungsanleitung

Velleman

Velleman MA620B Bedienungsanleitung

Velleman

Velleman HAM263D Bedienungsanleitung

Velleman

Velleman CAMSET2C Bedienungsanleitung

Velleman

Velleman HAM10N Bedienungsanleitung

Velleman

Velleman HAM06WS Bedienungsanleitung

Velleman

Velleman CCTVPROM15 Bedienungsanleitung

Velleman

Velleman DWH G955 Service-Handbuch

Velleman

Velleman CCTVPROMT1 Bedienungsanleitung

Velleman

Velleman CCTVPROM9 Bedienungsanleitung

Velleman

Velleman camset 29 Bedienungsanleitung

Velleman

Velleman CCTVPROM12 Bedienungsanleitung

Velleman

Velleman CCTVPROM7 Bedienungsanleitung

Velleman

Velleman HAM200 Bedienungsanleitung

Velleman

Velleman CAMSETW2 Bedienungsanleitung

Velleman

Velleman CTC1000SI Bedienungsanleitung

Velleman

Velleman HAM2828 Bedienungsanleitung

Beliebte Sicherheitssystem Handbücher anderer Marken

Inner Range

Inner Range Concept 2000 Bedienungsanleitung

Climax

Climax Mobile Lite R32 Montageanleitung

CADDX

CADDX NX-6 Bedienungsanleitung

FBII

FBII XL-31 Series Bedienungsanleitung

Johnson Controls

Johnson Controls PENN Connected PC10 Bedienungsanleitung

Aeotec

Aeotec Siren Gen5 Bedienungsanleitung

Blaupunkt

Blaupunkt SA 2700 Bedienungsanleitung

IDEAL

IDEAL Accenta Betriebsanleitung

AJAX

AJAX DoubleButton Bedienungsanleitung

Swann

Swann SW-P-MC2 Bedienungsanleitung

Ecolink

Ecolink Siren+Chime Bedienungsanleitung

Digital Monitoring Products

Digital Monitoring Products XR150 Bedienungsanleitung

EDM

EDM Solution 6+6 Wireless-AE Bedienungsanleitung

Highway Safety Group

Highway Safety Group EA401 Bedienungsanleitung

Siren

Siren LED GSM Bedienungsanleitung

Detection Systems

Detection Systems 7090i Montageanleitung

Se-Kure Controls

Se-Kure Controls MicroMini SK-4841 Bedienungsanleitung

Siemens

Siemens FDM273 Bedienungsanleitung