Velleman K6710 Bedienungsanleitung
Total solder points: 83
Difficulty level:
beginner 1o2þ3o4o 5oadvanced
K4101 / K6710
15 Channel infrared transmitter
ILLUSTRATED ASSEMBLY MANUAL H6710IP-ED1
þTactile Keyboard.
þComplete with aluminium Housing.
þTransmitter carrier wave frequency : 38KHz.
þNumber of identification codes : 6
þ15 independent channels.
þStandby current consumption : 0.1 µA.
þAverage current consumption during transmission : 10mA.
Works together with :
ØK6711 -15 Channel infrared receiver.
ØK6712/13 One Channel infrared receiver.
ØK4100 Digital controlled preamplifier.
ØK4500 digital synthesizer FM tuner.
þPower supply : 9V Battery (not included).
þDimensions : 50 x 23 x 175mm (2” x 0,9” x 6,9”).
Modification reserved
Features and specifications :
VELLEMAN Components NV
Legen Heirweg 33
9890 Gavere
Belgium
http://www.velleman.be
3
1. Assembly (Skipping this can lead to troubles ! )
Ok, so we have your attention. These hints will help you to make this project success-
ful. Read them carefully.
1.1 Make sure you have the right tools:
•A good quality soldering iron (25-40W)
with a small tip.
•Wipe it often on a wet sponge or cloth, to keep it clean; then apply solder to the
tip, to give it a wet look. This is called ‘thinning’ and will protect the tip, and en-
ables you to make good connections. When solder rolls off the tip, it
needs cleaning.
•Thin raisin-core solder. Do not use
any flux or grease.
•A diagonal cutter to trim excess wires. To avoid injury
when cutting excess leads, hold the lead so they can
not fly towards the eyes.
•Needle nose pliers, for bending leads, or to hold components in place.
•Small blade and Phillips screwdrivers. A basic range is fine.
For some projects, a basic multi-meter is required, or
might be handy
1.2 Assembly Hints :
⇒Make sure the skill level matches your experience, to avoid disappointments.
⇒Follow the instructions carefully. Read and understand the entire step before you
perform each operation.
⇒Perform the assembly in the correct order as stated in this manual
⇒Position all parts on the PCB (Printed Circuit Board) as shown on the drawings.
⇒Values on the circuit diagram are subject to changes.
⇒Values in this assembly guide are correct*
⇒Use the check-boxes to mark your progress.
⇒Please read the included information on safety and customer service
* Typographical inaccuracies excluded. Always look for possible last minute manual
updates, indicated as ‘NOTE’ on a separate leaflet.
0.000
Assembly hints
4
1.3 Soldering Hints :
Mount the component against the PCB surface and carefully solder the
leads
Make sure the solder joints are cone-shaped and shiny
Trim excess leads as close as possible to the solder joint
REMOVE THEM FROM THE TAPE
ONE AT A TIME !
AXIAL COMPONENTS ARE TAPED IN THE CORRECT
MOUNTING SEQUENCE !
Assembly hints
IPESF SDK NDGB FNL
C
O
D
E
CODICE
COLORE CODIGO
DE CORES CODIGO
DE COL-
ORES
VÄRI
KOODI FÄRG
SCHEMA FARVE-
KODE FARGE-
KODE FARB
KODE COLOUR
CODE CODIFI-
CATION
DES COU-
LEURS
KLEUR
KODE C
O
D
E
0Nero Preto Negro Musta Svart Sort Sort Schwarz Black Noir Zwart 0
1Marrone Castanho Marrón Ruskea Brun Brun Brun Braun Brown Brun Bruin 1
2Rosso Encarnado Rojo Punainen Röd Rød Rød Rot Red Rouge Rood 2
3Aranciato Laranja Naranjado Oranssi Orange Orange Orange Orange Orange Orange Oranje 3
4Giallo Amarelo Amarillo Keltainen Gul Gul Gul Gelb Yellow Jaune Geel 4
5Verde Verde Verde Vihreä Grön Grøn Grønn Grün Green Vert Groen 5
6Blu Azul Azul Sininen Blå Blå Blå Blau Blue Bleu Blauw 6
7Viola Violeta Morado Purppura Lila Violet Violet Violet Purple Violet Paars 7
8Grigio Cinzento Gris Harmaa Grå Grå Grå Grau Grey Gris Grijs 8
9Bianco Branco Blanco Valkoinen Vit Hvid Hvidt Weiss White Blanc Wit 9
AArgento Prateado Plata Hopea Silver Sølv Sølv Silber Silver Argent Zilver A
BOro Dourado Oro Kulta Guld Guld Guldl Gold Gold Or Goud B
5%
4K7= ( 4 - 7 - 2 - B )
1%
4K7= ( 4 - 7 - 0 - 1 - 1 )
COLOR= 2… 5
COLOR= 2...5
6
Construction
qD1 : 1N4148 or eq.
qD2 : 1N4148 or eq.
3. Diodes.
Watch the polarity !
D...
CATHODE
This infrared transmitter can be used to remotely operate our
preamplifier (K4100) or tuner (K4500). More over it can be used
together with the universal 15-channel receiver (K6711) and/or the
one-channel receivers (K6712/13). For use with those last two kits,
the transmitter has a universal keyboard, one of its keys even allows
you to reset all the outputs at once. Another so-called safety key
allows you to preserve the memory content (or stations in the case of
the tuner), in order to avoid unwanted overwriting. Not only its possi-
bilities but also the aluminium housing and a special VELLEMAN
tactile keyboard make this Build-it-yourself remote control unique.
qJ
1. Jump Wire
qR1 : 1K8 (1-8-2)
qR2 : 1K (1-0-2)
qR3 : 33 (3-3-0)
qR4 : 68 1/2W (6-8-0)
qR5 : 1 1/2W (1-0-B)
2. Resistors
R...
qIC1: 20P.
4. IC socket, Watch the
position of the notch !
7
Construction
J1
qJ1
5. PCB cable connector
qT1: BC547 or eq.
qT2: BC640 or eq.
6. Transistors
qC3 : 10µF
qC4 : 470µF
qC5 : 470µF
8. Electrolytic
Capacitors. (Watch the
polarity !)
C...
qC1 : 100 pF (101)
qC2 : 220 pF (221)
7. Capacitors.
qX1: 455KHz
9. Resonator.
8
Construction
FIG 1.0
First: Bend the leads exactly like the drawing.
Next: Solder one lead, and check the position, if neces-
sary correct by heating the soldering.
Last: Solder the second connection.
qLD2
qLD3
qLD4
10. Mounting the IR diodes. Watch the polarity !
C
C
C
Fit the IR diodes LD2
trough LD4 (see fig. 1.0)
horizontally and in line with
the pcb. Pay attention to
the polarity. Pass the short-
est lead trough the hole
marked C all like LD4.
9
Construction
FIG 2.0a
First carefully bend its leads at the component side, in
such a way as to make the longest lead (anode) touch R5
and the shortest lead touch R3.
After that you can solder the leads to the resistors and
cut the free ends. (See Fig. 2.0b)
qLD1
FIG 2.0b
11. Mounting the LED . Watch the polarity !
IMPORTANT
Fit LED LD1 at the solder side,
AGAINST the PCB (see fig. 2.0a)
10
Construction
qIC1 : 3004
FInsert IC1, 3004 type into his socket with his notch towards
the pcb edge.
13. IC. Watch the position of the notch !
Connect the connection wires of the battery holder to the
+ (red wire) and the -(black wire) of the pcb. (see fig 3.0)
qRed
qBlack
FIG 3.0
12. Battery.
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Velleman Sender Handbücher
Velleman
Velleman VM121 Bedienungsanleitung
Velleman
Velleman K8059 Bedienungsanleitung
Velleman
Velleman vm118 Bedienungsanleitung
Velleman
Velleman K8074 Bedienungsanleitung
Velleman
Velleman AVMOD11 Series Bedienungsanleitung
Velleman
Velleman CARSFM3 Bedienungsanleitung
Velleman
Velleman AVMOD17 Bedienungsanleitung
Velleman
Velleman K8074 Bedienungsanleitung
Velleman
Velleman K8058 Bedienungsanleitung
Velleman
Velleman SO11001 Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
