Ventev BTRM200 Bedienungsanleitung

VENTEV INNOVATIONS BTRM200 Battery Test Remote Monitoring System – User Guide V1.0

Innovations

BTRM200

Battery Test Remote Monitor

User Guide

Contact :

Ventev Innovations

10999 McCormick Road

Hunt Valley, MD 21031

Phone Number 800.759.9996

[email protected]

VENTEV INNOVATIONS BTRM200 Battery Test Remote Monitoring System – User Guide V1.0

Contents

1. Warnings...............................................................................................................................4

2. Supplied Accessories ............................................................................................................4

3. Overview...............................................................................................................................4

4. System Description ...............................................................................................................5

4.1. Overall System Connection Diagram.............................................................................5

4.2. System Connector Overview .........................................................................................5

5. Basic setup ............................................................................................................................6

5.1. Connecting unit to a PC.................................................................................................6

5.2. Initial Power up to set IP address..................................................................................6

5.3. Accessing your host computer’s network settings .......................................................7

5.4. Setting IP address information for BTRM default .........................................................8

5.5. Verify IP address information........................................................................................8

6. Unit Deployment ................................................................................................................13

6.1. Mounting.....................................................................................................................13

6.2. Wiring Battery Connection..........................................................................................13

6.3. Wiring Power Supply Connections ..............................................................................13

6.4. Wiring battery Charger Connections...........................................................................13

6.5. Alarm Connections ......................................................................................................13

6.6. Clearing Battery Test Data ..........................................................................................13

7. Web Interface Menus .........................................................................................................13

7.1. System Status Page .....................................................................................................14

7.2. Battery Status Page .....................................................................................................17

7.3. Battery Test Page ........................................................................................................18

7.3.1. Manual Test.................................................................................................................19

7.3.2. Capacity IO Check........................................................................................................19

7.3.3. Reset Battery Data and Setting to Defaults ................................................................19

7.4. Port Options Page ...........................................................................................................19

7.5. Email Configuration Page ............................................................................................22

7.6. Email Test Page ...........................................................................................................24

7.7. Network Configuration Page.......................................................................................24

7.8. DNP3 and Modbus ..........................................................................................................26

7.8.1. Addressing ...................................................................................................................26

7.8.2. DNP Retry Settings ......................................................................................................26

7.8.3. Communications Interface ..........................................................................................27

7.8.3.1. TCP/IP ......................................................................................................................27

7.8.3.2. RS232 .......................................................................................................................27

7.9. SNMP Configuration Page...............................................................................................27

VENTEV INNOVATIONS BTRM200 Battery Test Remote Monitoring System – User Guide V1.0

7.11. Help Page.....................................................................................................................30

7.12. About...........................................................................................................................31

8. SNMP Functionality ............................................................................................................31

8.2. SNMP Monitoring through a MIB Browser.....................................................................32

8.2.1. Install MIB Browser..................................................................................................32

8.2.2. Install SNMP MIB File...............................................................................................32

8.2.3. View BTRM via MIB Browser ...................................................................................33

8.2.4. Configure Trap Receiver ..............................................................................................35

8.2.5. Cannot Bind to Port 162 Error Message .....................................................................37

8.2.6. Open Trap Receiver .....................................................................................................40

8.3. Further Reading ..............................................................................................................44

9. Additional Protocols ...........................................................................................................44

9.1. DNP3 ...............................................................................................................................44

9.1.1. Overview .....................................................................................................................44

9.1.2. Data Link Layer ............................................................................................................44

9.1.3. Application Layer.........................................................................................................44

9.1.3.1. Function Support .....................................................................................................44

9.1.3.1.1. Enable Disable Unsolicited Event Status..............................................................45

9.1.3.2. Groups and Variations .............................................................................................45

9.1.3.3. Qualifiers..................................................................................................................45

9.1.3.4. Binary Input Status Points .......................................................................................45

9.1.3.5. Analog Input Status Points ......................................................................................46

9.1.3.6. Analog Output Status Points ...................................................................................46

9.1.3.7. Binary Output Status Point ......................................................................................47

9.1.3.8. Binary Output Write to Points .................................................................................47

9.1.3.9. Events ......................................................................................................................48

9.1.3.10. .....................................................................................................................................48

9.2. Mod Bus ..........................................................................................................................48

10. Additional Network Setup ..............................................................................................49

10.1. IP Reset ....................................................................................................................49

10.2. Router Ports.............................................................................................................49

10.3. Port Table.................................................................................................................50

11. Specifications and Warranty...........................................................................................50

VENTEV INNOVATIONS BTRM200 Battery Test Remote Monitoring System – User Guide V1.0

1. Warnings

Alarm Connections 1 and 2 rated for 60 Vdc, 80 ma max load. Do not exceed these ratings.

Do not connect to AC line powered loads.

2. Supplied Accessories

BTRM200 Monitor

3ft Ethernet Cable

3. Overview

Batteries age and their capacity slowly deteriorate until they need replacement. Also,

batteries can suddenly develop an internal fault that again limits their capacity. In an AC

Line Down situation, where batteries are used in critical back-up applications, these

conditions will result in premature, or in some cases immediate, system shutdown.

Although a battery’s state of charge can be inferred by monitoring the battery terminal

voltage while in standby mode, this voltage will not give an indication of actual capacity.

Furthermore, a battery that is marginal may not be detected until it is called upon to

perform, at which point it is too late to prevent a system failure. For a battery connected to

a charger that maintains a float voltage, neither condition can be checked.

In these cases, the BTRM200 is designed to evaluate battery capacity transparently to

system operation and provide network based notification should a battery fail or its

capacity drop below a specified level. This also has the advantage of allowing batteries that

exceed their nominal lifetime to remain in service, provided they meet capacity

requirements.

VENTEV INNOVATIONS BTRM200 Battery Test Remote Monitoring System – User Guide V1.0

4. System Description

4.1. Overall System Connection Diagram

4.2. System Connector Overview

4.2.1. Power Supply In Power Jack (P. Source +/ - and VenCh P+)

The BTRM must be connected to the load power supply in order to energize the

load while the battery charger is charging the battery.

4.2.2. Battery Charger In Power Jack (VenCh B+/ -)

The BTRM must be connected to the battery charger in order to charge the

battery bank after the battery capacity test is performed.

4.2.3. Battery In Power Jack (Battery +/-)

The battery bank must be connected directly to the BTRM in order to perform

the battery capacity test.

4.2.4. Alarm Connector (Alarm1 or I/O1, Alarm2 or I/O2)

BTRM has two independent, isolated relay contacts for alarm indication.

Contacts are normally open when power is off. The user can select normally

open or normally closed under an alarm condition. Do not exceed the contact

VENTEV INNOVATIONS BTRM200 Battery Test Remote Monitoring System – User Guide V1.0

maximum relay ratings of 60 Volts, 80 ma. Do not use to directly operate AC line

connected equipment.

5. Basic setup

5.1. Connecting unit to a PC

Notes on accessing a BTRM over Ethernet:

Technically you should be able to plug the device into your current network, regardless of

how your current network IP addressing is set up, and be able to reach the BTRM’s Status

and Setup web page by entering its IP address (found on the BTRM front label) in a Web

Browser on a local computer. However, in practice, not so easy, due to a wide variety of

possibly incompatible network addressing and firewall configurations. These difficulties

occur most often if someone else has set up the network settings, and in particular where

these settings are “managed” by software installed on your computer by your internet

provider or corporate IT departments.

To avoid these potential network issues at the initial evaluation stage it is best to connect

both your computer and the device to a hub/network switch (one that is not connected to

the rest of your network) or directly connect your computer to the BTRM with a cross-

connected Ethernet cable.

5.2. Initial Power up to set IP address

To power up the device, connect the battery to the BTRM. Power up the power supply

and battery charger. The BTRM starts in self-test mode for 5 to 15 seconds. PB1 and PB2

push button LEDs will blink.

Once the device is power up and cabled to the Ethernet, the GREEN LED will illuminate

on the Ethernet connector and startup should be complete within 30 sec.

VENTEV INNOVATIONS BTRM200 Battery Test Remote Monitoring System – User Guide V1.0

5.3. Accessing your host computer’s network settings

From the start button select Control Panel -> Network and Internet ->Network

Connections

Select the adapter that you plan to use and from the File menu, select properties.

This will bring up the properties window, shown on

the right.

Scroll down to the Internet Protocol Version 4

(IPv4) item, select it, and then select “properties”.

This will bring up the window to allow manual

configuration of the network adapter’s IP

addresses.

VENTEV INNOVATIONS BTRM200 Battery Test Remote Monitoring System – User Guide V1.0

5.4. Setting IP address information for BTRM default

Using a direct connection to the device with a

cross connected cable or using a network switch

(hub), use the manual IP settings shown on the

right. This property dialog can be found in the

TCP/IP properties, which is a sub dialog of the

Network Connections Properties, both found in

Control Panel Network Connections.

(Typically the default gateway and DNS server

need not be entered.)

If using a router, check your local area connection settings to see if the router gateway

address is the same as the default device gateway

of 192.168.1.1. If it’s not, you will need to use a

direct connection as described above to change

the device gateway address to match the router’s

gateway address.

5.5. Verify IP address information

For the initial configuration of the BTRM and to change Network IP settings for

placement in an IP based network you will need to connect the BTRM directly to your

PC. Once connected to your PC you will be able to configure the BTRM to match your

network settings.

VENTEV INNOVATIONS BTRM200 Battery Test Remote Monitoring System – User Guide V1.0

You will need the following information from your network administrator to add the

BTRM to your IP Network:

IP Address – we recommend using a static IP address for the BTRM

Gateway – what is the IP address of the Gateway of your network

Subnet Mask – what is the mask of your network

Primary DNS – IP address of the primary DNS server for your network

Once you have your connection made to you laptop or PC you will need to record your

IP address and verify connection to the BTRM.

NOTE: It may be necessary to give your PC or Laptop a static address to access the BTRM

default network.

Example: IP Address: 192.168.1.200

Subnet mask: 255.255.255.0

Use the following screen shots to guide you into finding your IP address and record your

address for use later.

1. Click Start and then Run.

2. In the window type cmd and click OK.

VENTEV INNOVATIONS BTRM200 Battery Test Remote Monitoring System – User Guide V1.0

3. Type ipconfig then <Enter>.

4. Record your IP Address

Andere Ventev Monitor Handbücher

Ventev

Ventev BTRM300 Bedienungsanleitung

Beliebte Monitor Handbücher anderer Marken

Linear Acoustic

Linear Acoustic LQ-1000 Bedienungsanleitung

AOC

AOC I2579V Bedienungsanleitung

Gateway

Gateway FPD1520 Bedienungsanleitung

Furuno

Furuno Mu 120c Bedienungsanleitung

Asus

Asus VB171D - 17" LCD Monitor Bedienungsanleitung

Dell

Dell S2230MX Gebrauchsanweisung

Philips

Philips 107C64 Bedienungsanleitung

Dell

Dell S2409WFP Bedienungsanleitung

EverFocus

EverFocus EN-7517E Bedienungsanleitung

Panasonic

Panasonic TH152UX1 - 152" PLASMA TV Bedienungsanleitung

Dell

Dell Precision 7680 Bedienungsanleitung

LG 50PM1M - - 50" Plasma Panel Bedienungsanleitung

Bosch

Bosch DDU 9 Bedienungsanleitung

Acer

Acer A231HL Bedienungsanleitung

Philips

Philips 86BDL4152T Bedienungsanleitung

NEC

NEC AccuSync LCD5V Bedienungsanleitung

Emay

Emay SleepO2 Bedienungsanleitung

IBM

IBM 6360 Montageanleitung