Ventis ECO-55 ST Bedienungsanleitung

INSTALLATION MANUAL

ECO-55 ST

(VB00022 model)

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 1/4"

439mm

36 1/8"

918mm

25 1/8"

639mm

22 7/8"

581mm

8 1/8"

205mm

15 3/4"

401mm

24 7/8"

632mm

29 1/2"

750mm

76mm

11 3/8"

290mm

6 1/8"

155mm

Safety tested according to ULC S627,UL1482 and

ASTM E1509 by an accredited laboratory

INSTALLATIONBYAPROFESSIONAL

IS STRONGLY RECOMMENDED

Stove Builder International inc.

250, rue de Copenhague,

St-Augustin-de-Desmaures (Québec) Canada

G3A 2H3

Customer service : 1-877-356-6663

Email : [email protected]

https://www.occanada.com/ca/fr/

CONTACT LOCAL BUILDING OR FIRE OFFICIALS ABOUT RESTRICTIONS AND INSTALLATION

INSPECTION REQUIREMENTS IN YOUR AREA.

PLEASE READ THIS ENTIRE MANUAL BEFORE INSTALLATION AND USE OF THIS PELLET FUEL-

BURNING ROOM HEATER. FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN

PROPERTY DAMAGE, BODILY INJURY OR EVEN DEATH.

READ AND KEEP THIS MANUAL FOR REFERENCE

This manual is available for free download on the manufacturer’s website. It is a copyrighted document. Re-sale

is strictly prohibited. The manufacturer may update this manual from time to time and cannot be responsible

for problems, injuries, or damages arising out of the use of information contained in any manual obtained from

unauthorized sources.

Printed in Canada 46352IA

2023-06-07

ENGLISH

Page 2 INSTALLATION MANUAL ECO-55 ST

ENGLISH

1. SAFETY INFORMATION

We highly recommend that our pellet burning hearth

products be installed and serviced by professionals

who are certied in the United States by NFI (National

Fireplace Institute ® ) or in Canada by WETT (Wood

Energy Technology Transfer) or in Quebec by APC

(Association des Professionnels du Chau󰀨age).

If this appliance is not properly installed,

combustible materials near it may overheat. To

reduce the risk of re, follow the installation

instructions in this manual exactly. Contact local

building or re o󰀩cials about restrictions and

installation inspection requirements in your area.

Please read this entire manual before you install and

use your new stove. You may need to get a building

permit for the installation of this appliance and the

venting system that it is connected to. Consult your

municipal building department or re department

before installation. We recommend that you also

inform your home insurance company to nd out if

the installation will a󰀨ect your policy.

WARNING

IFTHISSTOVEISNOTPROPERLYINSTALLED,

AHOUSE FIRE MAY RESULT. TO REDUCE THE

RISK OF FIRE, FOLLOW THE INSTALLATION

INSTRUCTIONS.

NOTICE

The information given on the certication label

a󰀩xed to the stove always overrides the information

published in any other media (owner’s manual,

catalogues, yers, magazines or web sites).

BURNING ANY SOLID FUELS GENERATES

CARBON MONOXIDE IN LOW

CONCENTRATION. THIS GAS IS EVACUATED

BY THE EXHAUST VENTING SYSTEM. IN

HIGHER CONCENTRATIONS, CARBON

MONOXIDEISTOXICANDMAYCAUSEDEATH.

TO PREVENT THIS, ENSURE THAT YOUR

EXHAUST VENTING SYSTEM IS AIRTIGHT.

WARNING

THIS STOVE IS NOT RECOMMENDED TO BE

INSTALLED IN A BEDROOM.

CAUTION

THIS STOVE MUST BE CONNECTED TO

A STANDARD 120V / 60HZ, GROUNDED

ELECTRICAL OUTLET. DO NOT USE AN

ADAPTERPLUGORSEVERTHE GROUNDING

PLUG. DO NOT ROUTE THE ELECTRICAL

CORDUNDERNEATH,INFRONTOROVERTHE

STOVE.

WARNING

THIS STOVE IS MOBILE HOME APPROVED

AND REQUIRES INSTALLATION OF A FRESH

AIR KIT, SOLD SEPARATELY. THE STOVE

MUST BEATTACHED TO THE STRUCTURE OF

THE MOBILE HOME AND THE STRUCTURAL

INTEGRITY OF THE MOBILE HOME FLOOR,

WALL, AND CEILING / ROOF MUST BE

MAINTAINED.DONOTINSTALLINASLEEPING

ROOM.

NOTICE

Mixing of appliance components from di󰀨erent

sources or modifying components is prohibited

and will void the warranty. Any modication of the

appliance that has not been approved in writing by

the testing authority is prohibited and violates CSA

B365 (Canada) and NFPA 211 (USA).

WARNING

NOTICE

When locating your appliance, make sure the vent

will not interfere with any truss, roof beams, wall

studs, water pipes or electrical wiring. It may be

easier to relocate appliance than to rework the

building structure.

Page 3

INSTALLATION MANUAL ECO-55 ST

ENGLISH

NOTICE

This stove has been developed and built for

residential supplementary heat source. Commercial

and industrial use is prohibited and will void the

warranty.

NOTICE

Stove Builder International inc. (SBI) grants no

warranty, implied or stated, for the poor installation

of your appliance and assumes no responsibility of

any consequential damages.

This product can expose you

to chemicals including carbon

monoxide, which is known to the

State of California to cause cancer,

birth defects or other reproductive

harm. For more information go to

www.P65warnings.ca.gov/

Page 4 INSTALLATION MANUAL ECO-55 ST

ENGLISH

TABLE OF CONTENTS

1. SAFETY INFORMATION ............................................................................... 2

2. GENERAL FEATURES.................................................................................. 5

2.1 OVERALL DIMENSIONS (VB00022)................................................................................6

2.2 REGULATIONS COVERING PELLET STOVE INSTALLATION ...................................6

2.3 CERTIFICATION LABEL LOCATION ..............................................................................6

3. CLEARANCES TO COMBUSTIBLE MATERIALS ...................................... 7

3.1 CLEARANCES TO COMBUSTIBLES MATERIALS, WALLS AND CEILING ...............7

3.2 FLOOR PROTECTION ......................................................................................................8

4. VENTING SYSTEM ........................................................................................ 9

4.1 GENERAL ...........................................................................................................................9

4.2 RECOMMANDATIONS ......................................................................................................9

4.3 EQUIVALENT VENT LENGTH (EVL)...............................................................................9

4.3.1 RECOMMENDED EXHAUST VENTING DIAMETER .......................................................9

4.3.2 INSTALLATION COMPLIANCE.......................................................................................10

4.4 TERMINATION LOCATION.............................................................................................11

4.5 DIRECT VENT SYSTEM ................................................................................................12

4.6 INSTALLATION CONFIGURATION ...............................................................................12

4.6.1 THROUGH WALL INSTALLATION (MAIN FLOOR OR BASEMENT).............................12

4.6.2 THROUGH ROOF INSTALLATION.................................................................................12

4.6.3 THROUGH A FACTORY BUILT CHIMNEY.................................................................13

4.6.4 THROUGH AN EXISTING MASONRY FIREPLACE..................................................13

4.6.5 THROUGH AN EXISTING MASONRY CHIMNEY......................................................14

5. INSTALLING THE OPTIONAL HOPPER EXTENSION............................ 14

6. MOBILE HOME INSTALLATION ................................................................ 15

7. INSTALLING A THERMOSTAT................................................................... 15

7.1 THERMOSTAT LOCATION .............................................................................................15

7.2 WIRED THERMOSTAT ....................................................................................................16

7.3 WIRELESS THERMOSTAT .............................................................................................16

8. COMBUSTION AIR SUPPLY ...................................................................... 16

8.1 SOURCES OF OUTSIDE COMBUSTION AIR ..............................................................17

9. APPLIANCE SET-UP ................................................................................... 18

9.1 GENERAL .........................................................................................................................18

10. WIRING DIAGRAM .................................................................................... 19

11. EXPLODED VIEWS AND PARTS LIST.................................................... 20

Page 5

INSTALLATION MANUAL ECO-55 ST

ENGLISH

2. GENERAL FEATURES

Recommended

chimney diameter

3 in. (75mm)

Flue outlet diameter 3 in. (75mm)

Type of chimney ULC/ORD-C441

CAN/ULC S609

UL 641 (TYPE L)

Approved for alcove

installation

Yes

Approved for mobile

home installation ‡

Yes

Shipping weight

(without option)

277 lb (DP00070-

DP00072)

286 lb (DP00071)

Appliance weight

(without option)

235 lb (DP00070-

DP00072)

242 lb (DP00071)

Particulate emission

standard

CSA B415.1-10

ASTM E2779

USA standard (safety) ASTM E1509

UL 1482

Canadian standard

(safety)

ULC S627

Electrical

requirements

Voltage and frequency

120VAC and 60Hz

Ignition : 3.02A

‡ Mobile home (Canada) or manufactured home (USA): The

US department of Housing and Urban Development describes

“manufactured homes” better known as “mobile homes” as

followed; buildings built on xed wheels and those transported on

temporary wheels/axles and set on a permanent foundation. In

Canada, a mobile home is a dwelling for which the manufacture

and assembly of each component is completed or substantially

completed prior to being moved to a site for installation on

a foundation and connection to service facilities and which

conforms to the CAN/CSA-Z240 MH standard.

Page 6 INSTALLATION MANUAL ECO-55 ST

ENGLISH

2.1 OVERALL DIMENSIONS (VB00022)

AFRESH AIR INLET

BFLUE OUTLET

2.2 REGULATIONS COVERING PELLET

STOVE INSTALLATION

When installed and operated as described in these

instructions, this pellet stove is suitable for use as a

freestanding heater in residential installations.

In Canada, the CSA B365 Installation Code for Solid

Fuel Burning Appliances and Equipment and the CSA

C22.1 Canadian National Electrical Code are to be

followed in the absence of local code requirements.

In the USA, the ANSI NFPA 211 Standard for

Chimneys, Fireplaces, Vents and Solid Fuel-Burning

Appliances and the ANSI NFPA 70 National Electrical

Code are to be followed in the absence of local code

requirements.

This stove must be connected to a pellet vent system

complying with the requirements for Pellet Vent in the

standards UL 103, UL 641, ULC S629M, CAN/ULC

S609 and ULC/ORD C441 or to a code-approved

masonry chimney with a stainless steel ue liner.

CAUTION

DO NOT USE MAKESHIFT MATERIALS OR

MAKEANYCOMPROMISESWHENINSTALLING

THIS STOVE.

2.3 CERTIFICATION LABEL LOCATION

Since the information given on the certication

label a󰀩xed to the stove always overrides the

information published in any other media (owner’s

manual, catalogues, yers, magazines or web sites),

it is important to refer to it in order to have a safe

and compliant installation. In addition, you will nd

important information about your stove (model, serial

number, etc.). You will nd the certication label on

the inner side of the hopper lid of the stove.

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 1/4"

439mm

36 1/8"

918mm

25 1/8"

639mm

22 7/8"

581mm

8 1/8"

205mm

15 3/4"

401mm

24 7/8"

632mm

29 1/2"

750mm

76mm

11 3/8"

290mm

6 1/8"

155mm

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 1/4"

439mm

36 1/8"

918mm

25 1/8"

639mm

22 7/8"

581mm

8 1/8"

205mm

15 3/4"

401mm

24 7/8"

632mm

29 1/2"

750mm

76mm

11 3/8"

290mm

6 1/8"

155mm

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 1/4"

439mm

36 1/8"

918mm

25 1/8"

639mm

22 7/8"

581mm

8 1/8"

205mm

15 3/4"

401mm

24 7/8"

632mm

29 1/2"

750mm

76mm

11 3/8"

290mm

6 1/8"

155mm

23 7/8"

607mm

24 7/8"

633mm

8 5/8"

218mm

17 1/4"

439mm

36 1/8"

918mm

25 1/8"

639mm

22 7/8"

581mm

8 1/8"

205mm

15 3/4"

401mm

24 7/8"

632mm

29 1/2"

750mm

76mm

11 3/8"

290mm

6 1/8"

155mm

Page 7

INSTALLATION MANUAL ECO-55 ST

ENGLISH

3. CLEARANCES TO COMBUSTIBLE

MATERIALS

The clearances shown in this section applies to

VB00022.

The clearances shown in this section have been

determined by tests according to procedures set out in

safety standards ULC S627 (Canada), ASTM E1509

(U.S.A) and UL1482 (U.S.A.). When the pellet stove

is installed so that its surfaces are at, or beyond, the

minimum clearances specied, combustible surfaces

will not overheat under normal and even abnormal

operating conditions.

WARNING

NO PART OF THE PELLET VENT SYSTEM MAY

BE LOCATED CLOSER TO COMBUSTIBLES

THANTHEMINIMUMCLEARANCESSPECIFIED

BY THE VENT MANUFACTURER.

WARNING

NO PART OF THE STOVE MAY BE LOCATED

CLOSER TO COMBUSTIBLES THAN THE

MINIMUM CLEARANCES SPECIFIED ON THE

CERTIFICATION LABEL.

NOTICE

The following clearances are also valid for an

alcove installation. However, if the stove is

installed in an alcove, to perform maintenance, you

should expect to move the appliance to get to the

maintenance access doors and components.

3.1 CLEARANCES TO COMBUSTIBLES

MATERIALS, WALLS AND CEILING

MINIMUM CLEARANCES

CANADA USA

A* 3" (76 mm) 3" (76 mm)

DNote 1 Note 1

I** 48" (1 220 mm) 48" (1 220 mm)

*From the rear panel

**Measured from the platform on which the product is installed.

RECOMMENDED CLEARANCES FOR

MAINTENANCE

CANADA USA

A* 12" (305 mm) 12" (305 mm)

MINIMUM CLEARANCES

CANADA USA

B6" (152 mm) 6" (152 mm)

DNote 1 Note 1

RECOMMENDED CLEARANCES FOR

MAINTENANCE

CANADA USA

B24" (610 mm) 24" (610 mm)

Note 1 : Refer to the exhaust venting system manufacturer’s

instructions for clearances to combustible materials.

Page 8 INSTALLATION MANUAL ECO-55 ST

ENGLISH

3.2 FLOOR PROTECTION

MINIMUM CLEARANCES

CANADA USA

C3" (76 mm) 3" (76 mm)

DNote 1 Note 1

RECOMMENDED CLEARANCES FOR

MAINTENANCE

CANADA USA

C12" (305 mm) 12" (305 mm)

DNote 1 Note 1

Note 1 : Refer to the exhaust venting system manufacturer’s

instructions for clearances to combustible materials.

FLOOR PROTECTION

CANADA** USA

E6" (152 mm)

From door opening

6" (152 mm)

From door opening

F6" (152 mm)

From door opening

6" (152 mm)

From door opening

CAUTION

THE STOVE MUST BE PLACED ON

A CONTINUOUS (GROUTED JOINTS)

NONCOMBUSTIBLE MATERIAL SUCH AS

CERAMIC TILE*, CEMENT BOARD, BRICK,

MILLBOARDOREQUIVALENT,ORANYOTHER

APPROVED OR LISTED MATERIAL SUITED

FOR FLOOR PROTECTION.

*Any type of tile will require a continuous non combustible sheet

beneath to prevent the possibility of embers falling through to the

combustible oor if cracks or separation should occur in the ni-

shed surface, this would include oor protection for built-in raised

hearths. Check local codes for approved alternatives.

**You may reduce the oor protection requirements to the values

shown in the previous table ONLY if the following actions are

respected: Allow for the appliance to shut-down and re to

be extinguished. Once completely cool and all blowers have

stopped you may proceed with opening the rebox or ash door.

Otherwise, see CSA B365.

Page 9

INSTALLATION MANUAL ECO-55 ST

ENGLISH

4. VENTING SYSTEM

CAUTION

CONNECT THIS STOVE ONLY TO A LISTED

PELLETEXHAUSTVENTINGSYSTEMFORUSE

WITH SOLID FUEL OR TO A LINED CHIMNEY

CONFORMING TO NATIONAL AND LOCAL

BUILDING CODES.

CAUTION

DO NOT CONNECT THIS STOVE TO ANY

OTHEREXISTINGVENTINGSYSTEMSERVING

ANOTHER APPLIANCE.

CAUTION

THEVENTINGSYSTEMMUSTBECOMPLETELY

AIRTIGHT AND PROPERLY INSTALLED.

ALL VENT CONNECTOR JOINTS MUST BE

SEALED AND FASTENED IN ACCORDANCE

WITH THE PELLET VENT MANUFACTURER’S

INSTRUCTIONS TO ENSURE CONSISTENT

PERFORMANCEANDAVOIDSMOKEANDASH

SPILLAGE..

CAUTION

DO NOT INSTALL A FLUE DAMPER IN THE

EXHAUST VENTING SYSTEM OF THIS UNIT.

CAUTION

DO NOT CONNECT TO OR USE IN

CONJUNCTIONWITHANYAIRDISTRIBUTION

DUCTWORK.

CAUTION

THEVENTINGSYSTEMSHOULDBECHECKED,

AT LEAST TWICE A YEAR FOR ANY BUILDUP

OF SOOT OR CREOSOTE.

4.1 GENERAL

Even though the chimney draft is mechanical, a sui-

table venting system will ensure a natural draft which

will prevent smoke spillage in your home if a power

outage occurs. Moreover, a suitable venting system

conguration will help getting the best e󰀩ciency out

of your stove when installed in accordance with the

required EVL.

4.2 RECOMMANDATIONS

In Canada, we recommend that you use a listed pel-

let vent that meets the CAN/ULC S609 or ULC/ORD

C441 Standard. A pellet vent listed to ULC S629M is

also suitable for installation with this stove.

For the United States, we recommend that you use a

listed pellet vent that meets the UL 641 Standard. A

pellet vent listed to UL 103 is also suitable for instal-

lation with this stove.

This stove can be vented in an existing factory-built

or masonry chimney with the addition of a stainless

steel liner, provided the chimney is more than 4" in

diameter. The liner should be listed and should meet

the ULC S635 CAN/ULC S640 standard in Canada

and the UL 1777 standard in the USA. Refer to the

instructions provided by the vent manufacturer,

especially when passing through a wall, ceiling or

roof.

The recommended venting system inner pipe diame-

ter is 3". Use a 4" pipe if you have more than 15 feet

of Equivalent Vent Length (EVL).

To calculate the Equivalent Vent Length of your ins-

tallation, use the following conversions:

Qty Type of pipe Equivalent vent

length (EVL)

1 90° elbow or ‘‘Tee’’ 5 feet

1 45° elbow 3 feet

1 foot horizontal pipe run 1 foot

1 foot vertical pipe run 1/2 foot

4.3 EQUIVALENT VENT LENGTH (EVL)

4.3.1 RECOMMENDED EXHAUST VENTING

DIAMETER

Page 10 INSTALLATION MANUAL ECO-55 ST

ENGLISH

Here is an example to help you calculate Equivalent

Vent Length. On the following gure the EVL can be

calculated like this:

2 feet of horizontal run (2 X 1' EVL) = 2' of EVL

90° elbow or "Tee" (1 X 5' EVL) =5' of EVL

12 feet of vertical run

(12' X 0.5' EVL)

= 6’ of EVL

Termination cap = 0' of EVL

Total EVL = 13' of EVL

Since the total EVL is less than 15 feet, the re-

commended exhaust venting diameter is 3".

4.3.2 INSTALLATION COMPLIANCE

To determine if your installation is compliant, the

exhaust venting system must end within the grid on

the venting system chart. The previous installation

has 2 feet of horizontal run and 12 feet of vertical

run. It is thus standard since the venting system ends

in the gridded area.

CAUTION

• Horizontal runs shall not exceed 9 feet.

• Never exceed 30 feet of evl.

CAUTION

TO REDUCE THE RISK OF SMOKE SPILLAGE

THERE SHOULD ALWAYS BE AT LEAST ONE

FOOTOFVERTICALRISEFOREACHFOOTOF

HORIZONTALRUN.INALLCASES,ATLEAST3

FEET OF VERTICAL RISE IS NEEDED.

WARNING

TERMINATIONOFASIDEWALLVENTSHOULD

BE LOCATED TO AVOID PERSONAL BURN

INJURY, FIRE HAZARD AND INTERFERENCE

WITH OR DAMAGE TO ADJACENT

PROPERTIES.EXHAUST GASES CAN REACH

TEMPERATURESOF500°F(260°C)ANDCAUSE

SERIOUS BURNS.

WARNING

TERMINATION COLLAR (SPARK ARRESTER)

ISMANDATORYAND MUST BE CLEAR OFANY

DEBRIS AT ALL TIME.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Ventis Herd Handbücher

Ventis

Ventis HE200 Bedienungsanleitung

Beliebte Herd Handbücher anderer Marken

Arada

Arada Cassette Stove Bedienungsanleitung

HearthStone

HearthStone Stowe DV 8321 Fehlerbehebungshandbuch

Cattara

Cattara FAMILY Bedienungsanleitung

Stanley

Stanley Argon F500 OVAL Bedienungsanleitung

Avalon

Avalon B-VENT Bedienungsanleitung

Nordpeis

Nordpeis Vega Bedienungsanleitung

Exquisit

Exquisit EKC601-5 Bedienungsanleitung

Stanley

Stanley Oisin Oil MK II Betriebsanleitung

Thermocet

Thermocet Brookfield S/CC Bedienungsanleitung

HASE

HASE delhi Bedienungsanleitung

Vermont Castings

Vermont Castings Intrepid 2 Bedienungsanleitung

Italiana Camini

Italiana Camini CLASSICA Kurzanleitung

Avalon

Avalon Vashon Avanti DVS FS Bedienungsanleitung

Spartherm

Spartherm ambiente a1 Bedienungsanleitung

Dimplex

Dimplex MCFSTV12AU Bedienungsanleitung

Warmlite

Warmlite WL46040 Bedienungsanleitung

Regency

Regency Ultimate U39E Series Kurzanleitung

Barton

Barton FH-AMP8745 Technisches Dokument