Vento Technologies Ventomist VTHPMF-2405 Bedienungsanleitung
VTHPMF-2405
High Pressure Misting Fan 24”
by
General Safety Information
MACHINE WARNING SIGNS
Indicates an imminently
hazardous situation which,
if not avoided, will result in
death or serious injury.
Indicates a potentially
hazardous situation which,
if not avoided, could result
in death or serious injury.
Indicates a potentially
hazardous situation which,
if not avoided, may result
in minor or moderate
injury.
Used without the safety
alert symbol ( ) indicates
potentially hazardous
situation which, if not
avoided, may result in
property damage.
Warning of electric shock
Do not expose the
equipment to rain or use in
damp locations.
Do not use the equipment
around flammable products,
if not avoided, sparks can
ignite vapors from
flammable products.
Read and understand all
warnings and operating
instructions before using this
equipment. Failure to follow
all instructions may result in
electric shock, fire, and/or
serious personal injury or
property damage.
Figure 1
VTHPMF-2405
High Pressure Misting Fan 24”
by
TABLE OF CONTENTS
MACHINE WARNING SIGNS.................................................................................. 2
General Safety Information................................................................................... 4
Installation .......................................................................................................... 6
Performance Record ……………………………………………………………………………………… 10
Front view………………………………………………………………………………………………………12
Back view………………………………………………………………………………………………………14
INSTRUCTIONS………………………………………………………………………………………………16
Repair Parts Illustration(Figure3) ........................................................................ 17
Repair Parts List(Figure3) ................................................................................... 18
Repair Parts Illustration(Figure4) ........................................................................ 19
Repair Parts List(Figure4) ................................................................................... 20
Repair Parts Illustration(Figure5) ........................................................................ 22
Repair Parts List(Figure5) ................................................................................... 26
How to clean the filter ........................................................................................ 32
VTHPMF-2405
High Pressure Misting Fan 24”
4
by
General Safety Information
To reduce the risk of short circuit, please place the unit in a dry area.
To reduce the risk of burns, do not touch the surface of the pump while
operating.
Do not handle the pump or motor with wet hands.
Check the hose for weak or worn areas and the pump’s oil level before each
use.
To reduce the risk of electric shock, turn off motor before any maintenance
and trouble shooting.
Please ensure the water source is turned on before operation, or the pump
will be damaged. Never run the pump without water.
While operating the pump, please supervise the safety of children.
VTHPMF-2405
High Pressure Misting Fan 24”
5
by
General Safety Information
△
!ATTENTION
Read the manual and safety precautions before using this misting fan.
Please make sure the misting fan is properly grounded.
While operating the misting fan, please supervise the safety of children.
To reduce the risk of short circuit, please place the misting fan in a dry place.
Please empty the water from the tank when not in use.
△
!WARNINGS
The electrical power supply voltage and frequency must match that specified on the
misting fan.
To reduce the risk of electric shock, turn off the motor before any maintenance and
troubleshooting.
The unit must not be run without water. Lack of water will cause serious damage to
the pump.
△
!DANGEROUS
To reduce the risk of burns, do not touch the surface of the pump while operating.
It is highly risky to use the misting fan without the ground-fault circuit-interrupter
(GFCI); this device is provided to avoid the risk of electric shock.
For safety concerns, please disconnect the plug of the misting fan from the power
supply when not in use.
Do not handle the pump or motor with wet hands.
Do not operate the misting fan in the rain or during thunderstorms.
VTHPMF-2405
High Pressure Misting Fan 24”
7
by
2. Make sure that the pump is firmly installed and the connectors are tightened
properly.
3. Before operating the motor, turn on the water source and check whether the
suction hose is connected to the pump properly. Discharge redundant air inside
the pump.
4. The water’s pressure should be at least 50 PSI.
5. Make sure the diameter of the suction hose is 3/4 inch.
6. Make sure the diameter of any extension cords used is larger than 18AWG.
B. Maintenance
1. Change the oil when the pump has been used for the first 30~50 hours.
2. After the initial oil change, replace the oil after every 100~200 hours of
operation.
3. Use #30~40 oil, add 70 cc each time.
C. Troubleshooting
1. UNSTABLE WORKING PRESSURE
(a) Check whether the suction hose is leaking, clogged or afloat.
(b) Drain out the redundant air by disconnecting the outlet hose.
(c) Check the valve assembly to see if it is clogged or damaged.(1)
2. INSUFFICIENT PRESSURE
(a) Check to see if the packing, waterproof seal(3) and valve assembly(1) are
damaged.
(b) Check to see if the pressure valve and regulating spring are worn out.(2)
3. LEAKAGE
(a) Check the U-Packing, waterproof seal and piston. Replace them if
necessary.(3)
VTHPMF-2405
High Pressure Misting Fan 24”
10
by
△
!ATTENTION
Please do not change the oil immediately after using the misting fan. The oil will be hot
and might cause personal injury. Wait at least 30 minutes before changing the oil.
TURNING OFF THE MISTING FAN & STORAGE
If the misting fan will not be used for a long period of time, please follow these
instructions.
1. Turn off the water supply and take off the suction hose.
2. Open the drain plug at the bottom of the water tank to release the water out. Clean
the filters (1) (2).
3. Press the air release valve to exhaust the air from the pump. Press to eliminate
the water frm the pump and hose. Pump will stop due to the duration of alarm
without water is 15 seconds. If water still remains, please unplug the power and plug
again to repeat this step.
4. Turn off the timer to stop spraying. Switch the fan speed knob to “0”to stop the fan.
5. Unplug the power cable from the socket.
6. Store the unit in a cool dry place away from hazardous conditions.
Inhaltsverzeichnis
