Vents Brig HRV 200 Bedienungsanleitung

USER’S MANUAL

Vents Brig HRV 200

Vents Brig HRV 300

Heat Recovery Ventilator

Brig HRV 200 (300)

Introduction ...............................................................................................

Application .................................................................................................

Delivery set .................................................................................................

Unit designation key ................................................................................

Basic unit dimensions .............................................................................

Technical data ...........................................................................................

Safety requirements ................................................................................

Structure and operating logic ..............................................................

Mounting and setting-up .......................................................................

Condensate drainage .............................................................................

Unit connection to power mains ........................................................

Unit control .................................................................................................

Servicing and maintenance .................................................................

Troubleshooting .......................................................................................

Storage and transportation rules .......................................................

Manufacturer’s warranty .......................................................................

CONTENT

INTRODUCTION

APPLICATION

DELIVERY SET

This user’s manual combines technical description, operation and service manual, technical

data sheet and installation guidelines for the heat recovery ventilator Brig HRV 200 (300), hereinafter

referred to as the unit.

The unit is designed to save thermal energy by means of heat recovery and is one of the

energy saving components used in the buildings and premises. The heat recovery ventilator is a

component unit and is not designed for independent operation.

The unit is designed to provide permanent controlled air exchange by mechanical

ventilation in houses, oces, hotels, cafés, conference halls and other residential and public premises

as well as utilization of extract air heat energy to warm up supply puried air.

The unit is for ceiling mounting.

The unit is rated for continuous operation always connected to power mains.

Transporting medium must not contain any ammable or explosive mixtures, evaporation

of chemicals, coarse dust, soot and oil particles, sticky substances, brous materials, pathogens or any

other harmful substances.

The unit is not designed to be used by children, physically or mentally

disabled persons, persons with sensory disorder, persons with no appropriate

experience or expertise.

The unit can be operated by qualied experts after appropriate instruction

about its use and operation.

The unit shall be mounted in places inaccessible for children.

Unit Brig HRV 200 (300) - 1 pce;

User’s manual - 1 pce; - 1 pce;

Drain hose - 1 pce;

Oil filter - 1 pce;

Packing box - 1 pce.

Brig HRV 200 (300)

Brig HRV 200(300)

Air capacity [CFM]

Unit type:

HRV - Heat Recovery Ventilator

UNIT DESIGNATION KEY

BASIC DIMENSIONS

Unit type Ø D A B C E F G H I

Brig HRV 200 6" 32

3/8”

7/16”

5/16”

5/8"

3/4” 6" 23

11/16”

5/8”

Brig HRV 300 8" 40

5/8”

3/4”

5/16” 8 5/8” 12

3/4”

7/16”

11/16”

9/16”

Table 1

Ø D

Fig. 1 Overall and connection dimensions

TECHNICAL DATA

SAFETY REQUIREMENTS

While operating and mounting unit fulll the requirements of the present operation manual

as well as general requirements of all applicable codes and standards valid in USA and Canada.

Ground the unit!

Before connecting the unit to power mains make sure that the unit is free of any visible

damages or any other foreign objects inside the casing that can damage the impeller blades.

Connection of the unit to power mains by duly qualied and authorized electricians only!

Do not!

• Do not operate the unit beyond the specied temperature range or in an aggressive

and explosive medium.

• Do not connect clothes dryers or similar equipment to the ventilation system.

• Do not operate the unit in the air and dust mixture environment.

Warning!

Mounting, servicing, connection and repair works of the unit are allowed after the

unit is disconnected from power mains.

The unit is designed for indoor application with the ambient temperature ranging from

+34 °F (1 °С) up to +122 °F (50 °С).

Ingress Protection rating:

IP44 for the unit motors;

IP 22 for the assembled unit connected to air ducts.

The Vents Brig HRV 200 unit net weight is 68 lbs (31 kg); the Vents Brig HRV 300 unit net

weight is 93 lbs (42 kg).

The unit series designation, basic overall and connecting dimensions are shown in g. 1

and in tables 1.

The unit design is regularly being improved, so some models can slightly dier from those

ones described in this manual.

Brig HRV 200 (300)

STRUCTURE AND OPERATING LOGIC

The unit has the following operating logic (g. 2):

Warm stale extract air from the room ows through the air ducts to the unit, is puried

in the extract lter and is supplied to the heat recovery core and exhausted outside by exhaust fan.

Clean cold air from outside is moved by supply fans to the unit where it is puried through the supply

lter. Then clean air ows through the heat recovery core and is supplied to the room by supply fan.

Thermal energy of warm extract air is transferred to clean intake fresh air and warms it up.

The extract and intake air ows are fully separated during heat recovery which excludes any transfer

of odors and pathogens to supply air. Heat recovery minimizes thermal energy losses, energy demand

and heating costs.

EXTRACT AIR

INTAKE AIR

EXHAUST AIR

SUPPLY AIR

INTAKE AIR

EXHAUST AIR

EXTRACT AIR

SUPPLY AIR

BRIG HRV 300

BRIG HRV 200

3 4

Fig. 2. Unit structure and operating logic

MOUNTING AND SETTING-UP

Fig. 3. Unit mounting

1. Supply fan with backward curved blades and maintenance-free motor with external rotor and

integrated thermal protection.

2. Extract fan with backward curved blades and maintenance-free motor with external rotor and

integrated thermal protection.

3. Plate cross ow heat recovery core that can be replaced with a summer block when no need

for heat recovery.

4. G4 supply air lter.

5. G4 extract air lter.

6. Drain pan.

7. Drain hose (included into delivery set).

8. Frost protection thermostat.

While mounting the unit provide enough access for the unit maintenance and servicing.

Mount the unit to ceiling with threaded rods xed inside the dowels attached to the ceiling or by

means of the belts that are rigidly xed to horizontal plane. The unit can be installed on mounting

supports with adjustable height for connection to the drain system (g. 3).

min 4”

min 20”

Brig HRV 200 (300)

CONDENSATE DRAINAGE

To attain the best performance of the unit while mounting provide a straight 20’’ (500

mm) duct section in front and behind the unit. The unit must be equipped with a grille with the

mesh width up to 1/2” or any other protecting device to prevent free access to the unit fans.

The unit is equipped with a condensate drain hose for condensate drainage (g. 4).

Connect the drain hose (1), U-trap (3) and drain system (5) with metal, plastic or rubber pipes (2 and 4).

The pipes must be sloped down at least by 3°. Before starting operation of the unit ll the system with

water and check that U-trap is always lled with water. Make sure that the water drainage is correct,

otherwise some condensate may be accumulated inside the unit and provoke subsequent equipment

damage and water ingress to the room. The condensate drainage system is designed for operation at

the ambient temperature above 32 ºF(0 °С). If the ambient temperature is below 32 ºF(0 °С), insulate

the drain system and provide air heating.

min 3°

g. 4. Condensate drainage

CONNECTION TO POWER MAINS

Cut power supply o before any operations with the unit. The unit shall be

connected to power mains by a duly qualied electrician only. Rated values of the

electrical parameters are shown on the rating plate. Any modications of the internal

connections are not allowed and will void the warranty.

The unit is designed for connection to single-phase ac 120 V / 60 Hz power mains.

The unit is equipped with a power cable and a plug and can be connected to any standard

grounded outlet. The power cable is connected to the terminal X1 by default.

Connect the unit to power mains through the external automatic switch integrated into the

xed wiring system that breaks the circuit in case of short circuit or overload.

Install the circuit breaker to have a free quick access in case of need to turn the unit o

promptly.

The unit has overload protection provided by the thermal fuse which is activated in case of

overload or short circuit. To replace the thermal fuse, disconnect the unit from power mains, remove the

overload or short circuit. Remove the thermal fuse and check the unit.

Wiring diagram is shown in g. 6.

The thermostat TS1 (g. 6) provides freezing protection of the unit during cold season. As

the thermostat is activated, the supply fan stops and the heat recovery core is warmed up with extract

air stream. To adjust the thermostatic switch, rotate the control dial to required setpoint. The setpoint

depends on the operating conditions. Recommended setting of the thermostat is 37°F (+3ºС), set in the

factory by default.

РЕ

Kon 1

Kon 2

PE M1

PE M2

Brown M1

Cap1

Black M1

Cap1

Black M2

Cap2

Brown M2

Cap2

Blue M1

Term

Blue M2

Х1

Х2

Х3

SW1

Сap1

Сap2

TS1

М1

FANMOTOR

М2

FANMOTOR

SW2

Low

Standby

Med

К1 К2 К3

910

SetupofLow SetupofMed

termostat

Low

Med

High

~24V

Twowire

control

Y/G

1513

~24V

~120V

Х5.1

Х5.2

Х6.1

Х6.2

RedRed

White

TR1

Green

Black

White

120V 60Hz

Х4

Fig. 5. Unit wiring diagram

Brig HRV 200 (300)

UNIT CONTROL

The unit is controlled by a three-position speed switch that enables low-speed modes «Low»

as well as «Med» and «Stand by» mode which enables total air quality control (g. 6).

Up to ve external control devices may be connected to the terminals 2-11 (g. 7) that turn

the unit to high-speed ventilation in case of activation of any of the control devices.

Switch the three-position speed controller to «Standby» mode for correct

operation from the remote control panel.

Fig. 6. Unit control

Three-speed switch

Terminals for connection of the

remote control panel

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vents Lüfter Handbücher

Vents

Vents TwinFresh Style Wi-Fi Bedienungsanleitung

Vents

Vents VKP SERIES Bedienungsanleitung

Vents

Vents KSB 100 Bedienungsanleitung

Vents

Vents VKMz 125 Bedienungsanleitung

Vents

Vents TwinFresh Expert Bedienungsanleitung

Vents

Vents KSB EC Series Bedienungsanleitung

Vents

Vents TwinFresh Comfo RA1-25 Bedienungsanleitung

Vents

Vents RO Series Bedienungsanleitung

Vents

Vents TwinFresh Expert RW-30 V.2 Bedienungsanleitung

Vents

Vents TwinFresh Expert RW1-50S3-13 V.2 Bedienungsanleitung

Vents

Vents VK EC Series Bedienungsanleitung

Vents

Vents MA Reverse Bedienungsanleitung

Vents

Vents HW-600x350-2 Bedienungsanleitung

Vents

Vents VKP EC SERIES Bedienungsanleitung

Vents

Vents ICF Series Bedienungsanleitung

Vents

Vents DRF-OV Bedienungsanleitung

Vents

Vents Centro-MZ 100 Bedienungsanleitung

Vents

Vents TwinFresh Comfo RB1-50 Bedienungsanleitung

Vents

Vents 100 Quiet-dMEV DC Bedienungsanleitung

Vents

Vents FB-K2 Series Bedienungsanleitung

Vents

Vents TwinFresh Comfo RA-25 Bedienungsanleitung

Vents

Vents Quiet 100 DC Bedienungsanleitung

Vents

Vents TT Silent-M Series Bedienungsanleitung

Vents

Vents TwinFresh Style Wi-Fi Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung

Litex Industries

Litex Industries E-CGL52CB5C1 Bedienungsanleitung

Vents brig HRV 200 Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken