VERDER CARBOLITE GERO SNF Handbuch

Installation, Operation and Maintenance Instructions

900 °C Swelling Number Furnace: SNF

2132 Controller

SNF + 2132 Controller

MEN-SNF-003_2132 (10-01-2019)

Contents

This manual is for guidance on the use of the Carbolite Gero product specified on the

front cover. This manual should be read thoroughly before unpacking and using the

furnace or oven. The model details and serial number are shown on the back of this

manual. Use the product for the purpose for which it is intended.

1.0 Symbols and Warnings 5

1.1 Switches and Lights 5

1.2 General Warnings 5

2.0 Installation 6

2.1 Unpacking and Handling 6

2.2 Siting and Setting Up 6

2.3 Electrical Connections 7

3.0 2132 Controller 9

3.1 Description 9

3.2 2132 Controller Operation 9

3.2.1 Controls 9

3.2.2 2132 Controller Operation 10

3.2.3 Basic Operation 10

3.2.4 Altering the Setpoint 10

3.2.5 Stopping and Starting Control 11

3.2.6 Altering the Ramp Rate 11

3.3 Operating with the Timer 12

3.3.1 Setting the Timer Mode 14

3.3.2 Setting the Time Period 14

3.3.3 Running with the Timer 14

3.3.4 Stopping the Timer 15

3.3.5 End of Time Period 16

3.3.6 Cancelling the Alarm 16

3.3.7 Program Example 16

3.4 Altering Power Limit 16

3.5 Audible Alarm 19

3.6 Temperature Controller Replacement 19

3.7 Navigation Diagram 20

4.0 2132 Over-Temperature Controller Description (if fitted) 22

4.1 Description 22

4.2 Operation 22

4.2.1 Controls 22

4.2.2 Operation 23

4.2.3 Over-Temperature Operation 23

4.2.4 Over-Temperature Alarm 23

4.2.5 Resetting the Over-Temperature Alarm 23

4.2.6 Sensor Break 23

4.3 Audible Alarm 24

4.4 Navigation Diagram 24

5.0 Operation 25

5.1 Operating Cycle 25

5.2 General Operating Advice 25

5.3 Notes on Test 26

5.4 Operator Safety 26

6.0 Maintenance 27

6.1 General Maintenance 27

6.2 Maintenance Schedule 27

6.2.1 Cleaning 29

6.3 Calibration 29

6.4 After-Sales Service 29

6.5 Recommended Spare Parts and Spare Parts Kit 29

6.6 Power Adjustment 29

7.0 Repairs and Replacements 31

7.1 Safety Warning - Disconnection from Power Supply 31

7.2 Safety Warning - Refractory Fibre Insulation 31

7.3 Panel Removal 31

7.4 Temperature Controller Replacement 32

7.5 Thermocouple Replacement 32

7.6 Element Replacement 32

7.7 Fuse Replacement 32

7.8 Solid-State Relay Replacement 33

8.0 Fault Analysis 34

A. Furnace Does Not Heat Up 34

B. Product Overheats 35

9.0 Wiring Diagrams 36

9.1 WA-11-00 36

9.2 WA-11-01 37

10.0 Fuses and Power Settings 38

10.1 Fuses 38

10.2 Power Settings 38

11.0 Specifications 39

11.1 Environment 39

1.0 Symbols and Warnings

1.1 Switches and Lights

Instrument switch: when the instrument switch is operated the

temperature control circuit is energised.

Heat light: the adjacent light glows or flashes to indicate that power

is being supplied to the elements.

1.2 General Warnings

DANGER – Electric shock. Read any warning printed next to this

symbol.

WARNING: Risk of fatal injury.

DANGER – Hot surface. Read any warning printed next to this

symbol.

WARNING: All surfaces of a product may be hot.

DANGER – Read any warning printed next to this symbol.

Caution – Double Pole/Neutral Fusing

1.0 Symbols and Warnings

2.0 Installation

2.0 Installation

2.1 Unpacking and Handling

When unpacking and handling the product, always lift it by its base. Do not use the door

or any other projecting cover or component to support the equipment when moving it.

Use two or more people to carry the product where possible.

Carefully remove any packing material from inside and around the product before use.

Avoid damaging the surrounding insulation when removing packing materials.

NOTE: This product contains Refractory Ceramic Fibre (also known as

Alumino Silicate Wool - ASW). For precautions and advice on handling

this material see section 7.2.

2.2 Siting and Setting Up

Place the product on a level surface in a well ventilated area.

Site away from other sources of heat and on a non-flammable surface that is resistant

to accidental spillage or hot materials.

The surface on which the equipment is mounted should be stable and not subject to

movement or vibrations.

The height of the mounting surface is important to avoid operator strain when loading

and unloading samples.

Unless otherwise stated elsewhere in this manual, ensure that there is at least 150

mm of free space around the back and sides of the product. Clear space is required

above the product to dissipate heat.

Ensure that the product is placed in such a way that it can be quickly switched off or

disconnected from the electrical supply.

This product is supplied with a crucible holder (a small component made of wire).

Ensure that this is present.

Under no circumstances should any objects be placed on top of the product.

Always ensure that any vents on the top of the product are clear of any

obstruction. Always ensure all cooling vents and cooling fans (if fitted) are

clear of any obstruction.

2.3 Electrical Connections

Connection by a qualified electrician is recommended.

This product requires a single-phase A.C. supply with earth (ground), which may be Live

to Neutral non-reversible (polarised), Live to Neutral reversible (non-polarised), or Live

to Live.

Check the product rating label before connection. The supply voltage should agree with

the voltage on the label and the supply capacity should be sufficient for the current on

the label.

The supply should be fused at the next size equal to, or higher than the current on the

label. A table of the most common fuse ratings is also given towards the back of this

2.0 Installation

manual. When the mains cable is factory fitted, internal fuses are also fitted. It is

essential that the operator ensures that the product is correctly fused.

Products with a factory fitted supply cable are designed to be wired directly to an

isolator or fitted with a line plug.

Products without a factory fitted supply cable require a permanent connection to a fused

and isolated supply. The product's electrical access panel should be temporarily

removed, and connections made to the internal terminals.

If the product is to be connected by line plug. The plug should be within reach of the

operator and should be easy to remove.

When connecting the product to an isolating switch ensure that both conductors (single

phase) or on all live conductors (three phase), and should be within reach of the

operator.

The supply MUST incorporate an earth (ground).

Supply Terminal Label Cable Colour

Supply Types

Live - Neutral Reversible or Live-

Live

1-phase L Brown to live

to either power

conductor

(For USA 200-240V,

connect L1)

N Blue to neutral

to the other power

conductor

(For USA 200-240V,

connect L2)

PE Green/ Yellow to earth

(ground) to earth (ground)

Electrical Connection Details:

3.0 2132 Controller

3.1 Description

The 2132 Controller is made by Eurotherm, and is fitted and configured by Carbolite

Gero for immediate use. It is a digital instrument with PID control algorithms.

The 2132 Controller features:

lEasy use as a simple temperature controller, where on setting the required tem-

perature the controller immediately attempts to reach and maintain it.

lA ramp-to-setpoint feature, which may be used to limit the heating (or cooling).

lA timer function which allows for heating for a predetermined time, either from start

or from reaching temperature; or alternatively for delaying the start of heating.

lAn alarm output which may be used in conjunction with the timer, for example to

give an audible alarm at the end of the timing period.

3.2 2132 Controller Operation

3.2.1 Controls

Most Carbolite Gero products are fitted with an instrument switch which cuts off power

to the controller and other parts of the control circuit.

To operate the controller, power must be supplied to the product and the instrument

switch must be on. If a time switch is included in the product circuit, this must be in the

'ON' position.

When an over-temperature condition occurs, the controller cuts the power to a

contactor, which in turn cuts power to the heating elements. Power is not restored until

the controller is 'reset'.

Some components will operate after the over-temperature feature isolates the power

supply e.g. cooling fans will continue to operate, provided that there is a power supply

to the product. In some cases the product may not do so, if other options (such as a

door switch) are fitted.

3.0 2132 Controller

3.2.2 2132 Controller Operation

Key

A Alarm Light

B Page

C Scroll

D Down

E Up

F Display

When switched on, the controller lights up, goes through a short test routine and then

displays the measured temperature or the over-temperature setpoint.

The page key allows access to parameter lists within the controller.

A single press of the page key displays the temperature units, normally set to °C;

further presses reveal the lists indicated in the navigation diagram. See section 4.4.

The scroll key allows access to the parameters within a list. Some parameters are

display-only; others may be altered by the operator.

A single press of the scroll key in the 'Home' list displays the temperature units;

further presses reveal the parameters in the current list indicated in the navigation

diagram.

To return to the 'Home' list at any time, press page and scroll together, or wait

for 45 seconds.

The down and up keys are used to alter the setpoint or other parameter values.

3.2.3 Basic Operation

Normally no operator action is required other than entering the setpoint, as the

controller starts to control on being switched on, as described above.

3.2.4 Altering the Setpoint

With the display at 'Home', showing the measured temperature, press down or up

once to display the setpoint; press again or hold down to adjust it. The display returns to

the measured temperature when no key is pressed for 30 seconds.

Andere Handbücher für CARBOLITE GERO SNF

Inhaltsverzeichnis

Andere VERDER Ofen Handbücher

VERDER

VERDER CARBOLITE GERO VMF 10/6 Handbuch

VERDER

VERDER CARBOLITE GERO CFM 14/2 Handbuch

VERDER

VERDER Carbolite HZS Series Leitfaden

VERDER

VERDER CARBOLITE GERO HST 12/450 Handbuch

VERDER

VERDER Carbolite Gero CF 60B Handbuch

VERDER

VERDER CARBOLITE GERO G Series Handbuch

VERDER

VERDER CARBOLITE GERO AAF 11/7 Handbuch

VERDER

VERDER CARBOLITE GERO BLF 17/8 Handbuch

VERDER

VERDER CARBOLITE GERO BLF 18/3 + No Controller Handbuch

VERDER

VERDER CARBOLITE GERO E Series Handbuch

VERDER

VERDER CARBOLITE GERO G Series Handbuch

VERDER

VERDER CARBOLITE GERO MTF 12/25 Series Handbuch

VERDER

VERDER CARBOLITE GERO EZS-3G 12/600 Handbuch

VERDER

VERDER Carbolite Gero CWF 11 Handbuch

VERDER

VERDER Carbolite Gero CWF 12/5 Handbuch

VERDER

VERDER CARBOLITE GERO CFM 14/1 Handbuch

VERDER

VERDER CARBOLITE GERO VCF 12/23 Handbuch

VERDER

VERDER CARBOLITE GERO EHA 12/150B Handbuch

VERDER

VERDER CARBOLITE GERO KZS 12/600 Handbuch

VERDER

VERDER CARBOLITE GERO GHC 12/450 Handbuch

VERDER

VERDER CARBOLITE GERO AAF 11/3 Handbuch

VERDER

VERDER CARBOLITE GERO BLF 18/3 Handbuch

VERDER

VERDER CARBOLITE GERO RHF 14/35 Handbuch

VERDER

VERDER TZF 12/65/550 Handbuch

Beliebte Ofen Handbücher anderer Marken

Armstrong

Armstrong EG7H SERIES Bedienungsanleitung

Payne

Payne PG92ESA Leitfaden

SUPREME

SUPREME FEM10-M2301CM-A Montageanleitung

Ingersoll-Rand

Ingersoll-Rand S9V2B080D4VSAC/D Montageanleitung

Johnson Controls

Johnson Controls TM9T Leitfaden

Fluke

Fluke 9118A Bedienungsanleitung

Lennox

Lennox EL195UHE Elite Series Installations- und Betriebshandbuch

Intertherm

Intertherm M7RL Series Bedienungsanleitung

HDG

HDG Pelletmaster 15 Bedienungsanleitung

Pinnacle

Pinnacle Aero Bella AB-716C-QH Handbuch

Nortek

Nortek MG2S Series Bedienungsanleitung

Goodman

Goodman GMV9 Handbuch

SUPREME

SUPREME SUP10-M2301C Montageanleitung

Dettson

Dettson AMT400B34-SM1PMA Montageanleitung

Evcon

Evcon DGD 60 MBH Bedienungsanleitung

Trane

Trane S8B1A026M2PSAB Montageanleitung

Hart Sceintific

Hart Sceintific 9113 Bedienungsanleitung

Whirlpool

Whirlpool Gold WGGE45 Bedienungsanleitung