Vertex Standard FT-2900R Bedienungsanleitung
FCC ID: K6620393X50
IC: 511B-20393X50
Alignment
Vertex Standard Co.,Ltd.1
FT-2900R Alignment
Introduction
The FT-2900R is carefully aligned at the factory for the specified performance across
the amateur band. Realignment should therefore not be necessary except in the event
of a component failure. Only an authorized Vertex Standard representative should
perform all component replacement and service, or the warranty policy may be void.
The following procedures cover the adjustments that are not normally required once
the transceiver has left the factory. However, if damage occurs and some parts
subsequently are replaced, realignment may be required. If a sudden problem occurs
during normal operation, it is likely due to component failure; realignment should not
be done until after the faulty component has been replaced.
We recommend that servicing be performed only by authorized Vertex Standard service
technicians who are experienced with the circuitry and fully equipped for repair and
alignment. If a fault is suspected, contact the dealer from whom the transceiver was
purchased for instructions regarding repair. Authorized Vertex Standard service
technicians realign all circuits and make complete performance checks to ensure
compliance with factory specifications after replacing any faulty components.
Those who do undertake any of the following alignments are cautioned to proceed at
their own risk. Problems caused by unauthorized attempts at realignment are not
covered by the warranty policy. Also, Vertex Standard reserves the right to change
circuits and alignment procedures in the interest of improved performance, without
notifying owners.
Under no circumstances should any alignment be attempted unless the normal
function and operation of the transceiver are clearly understood, the cause of the
malfunction has been clearly pinpointed and any faulty components replaced, and
realignment determined to be absolutely necessary.
Required Test Equipment
The following test equipment (and familiarity with its use) is necessary for complete
realignment. Correction of problems caused by misalignment resulting from use of
improper test equipment is not covered under the warranty policy. While most steps do
not require all of the equipment listed, the interactions of some adjustments may
require that more complex adjustments be performed afterwards.
Do not attempt to perform only a single step unless it is clearly isolated electrically
from all other steps. Have all test equipment ready before beginning and, follow all of
FCC ID: K6620393X50
IC: 511B-20393X50
Alignment
Vertex Standard Co.,Ltd.2
the steps in a section in the order presented.
RF Signal Generator with calibrated output level at 200 MHz
Deviation Meter (linear detector)
In-line Wattmeter with 5% accuracy at 200 MHz
50-Ohm 100-W RF Dummy Load
8-Ohm AF Dummy Load
Regulated DC Power Supply adjustable from 6 to 15 VDC, 20A
Frequency Counter: 0.2-ppm accuracy at 200 MHz
AF Signal Generator
AC Voltmeter
DC Voltmeter: high impedance
VHF Sampling Coupler
SINAD Meter
Alignment Preparation & Precautions
A 50-Ohm RF load and in-line wattmeter must be connected to the antenna jack in all
procedures that call for transmission; alignment is not possible with an antenna. After
completing one step, read the next step to see if the same test equipment is required. If
not, remove the test equipment (except dummy load and wattmeter, if connected)
before proceeding.
Correct alignment requires that the ambient temperature be the same as that of the
transceiver and test equipment, and that this temperature be held constant between
68 °F ~ 86 °F (20 °C ~ 30 °C). When the transceiver is brought into the shop from hot or
cold air, it should be allowed some time to come to room temperature before alignment.
Whenever possible, alignments should be made with oscillator shields and circuit
boards firmly affixed in place. Also, the test equipment must be thoroughly warmed up
before beginning.
Note: Signal levels in dB referred to in the alignment procedure are based on 0dBµ =
0.5µV.
Test Setup
Set up the test equipment as shown below for transceiver alignment.
Entering the Alignment Mode
Alignment of the FT-2900R is performed using a front panel software-based procedure.
FCC ID: K6620393X50
IC: 511B-20393X50
Alignment
Vertex Standard Co.,Ltd.3
To perform alignment of the transceiver, it must first be placed in the “Alignment
Mode,” in which the adjustments will be made and then stored into memory.
To enter the Alignment mode, press and hold in the [REV(DW)] and [D/MR(MW)] keys
while turning the radio on. Once the radio is on, release these two key. The transceiver
is now in the “Alignment Mode.”
PLL Reference Frequency
Rotate the DIAL knob to set the alignment parameter to “146.000 rF.”
Press the [D/MR(MW)] key to enable adjustment of the “PLL Reference Frequency.”
Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the
counter frequency reading is 146.000 MHz (±100 Hz).
Press the [D/MR(MW)] key.
RF Front-end Tuning
Inject a 145.100 MHz signal at a level of –10 dBµ (with 1 kHz modulation @±3.5
kHz deviation) from the RF signal generator.
Rotate the DIAL knob to set the alignment parameter to “145.100 tn.”
Press the [D/MR(MW)] key to enable adjustment of the “RF Front-end Tuning.”
Adjust the DIAL knob so that the maximum SINAD.
Press the [D/MR(MW)] key.
Squelch Threshold Level
Inject a 145.100 MHz signal at a level of –14 dBµ (with 1 kHz modulation @±3.5
kHz deviation) from the RF signal generator.
Rotate the SQL knob to the 10-o’clocl position.
Rotate the DIAL knob to set the alignment parameter to “145.100 tL.”
Press the [D/MR(MW)] key to enable adjustment of the “Squelch Threshold Level.”
Press the [D/MR(MW)] key three times.
Press the [D/MR(MW)] key.
S-meter Level (S-1)
Inject a 145.100 MHz signal at a level of –5 dBµ (with 1 kHz modulation @±3.5 kHz
deviation) from the RF signal generator.
Rotate the DIAL knob to set the alignment parameter to “145.100 S1.”
Press the [D/MR(MW)] key to enable adjustment of the “S-meter Level (S-1).”
FCC ID: K6620393X50
IC: 511B-20393X50
Alignment
Vertex Standard Co.,Ltd.4
Press the [D/MR(MW)] key three times.
Press the [D/MR(MW)] key.
S-meter Level (S-9)
Inject a 145.100 MHz signal at a level of +23 dBµ (with 1 kHz modulation @±3.5
kHz deviation) from the RF signal generator.
Rotate the DIAL knob to set the alignment parameter to “145.100 S9.”
Press the [D/MR(MW)] key to enable adjustment of the “S-meter Level (S-9).”
Press the [D/MR(MW)] key three times.
Press the [D/MR(MW)] key.
TX Power (High)
Rotate the DIAL knob to set the alignment parameter to “145.000 HP.”
Press the [D/MR(MW)] key to enable adjustment of the “TX Power (High).”
Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the
RF Power Meter reading is 75 W (±3.0W).
Press the [D/MR(MW)] key.
TX Power (Low 3)
Rotate the DIAL knob to set the alignment parameter to “145.000 L3.”
Press the [D/MR(MW)] key to enable adjustment of the “TX Power (Low 3).”
Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the
RF Power Meter reading is 30 W (±1.5 W).
Press the [D/MR(MW)] key.
TX Power (Low 2)
Rotate the DIAL knob to set the alignment parameter to “145.000 L2.”
Press the [D/MR(MW)] key to enable adjustment of the “TX Power (Low 2).”
Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the
RF Power Meter reading is 10 W (±1.0 W).
Press the [D/MR(MW)] key.
TX Power (Low 1)
Rotate the DIAL knob to set the alignment parameter to “145.000 L1.”
Press the [D/MR(MW)] key to enable adjustment of the “TX Power (Low 1).”
Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the
FCC ID: K6620393X50
IC: 511B-20393X50
Alignment
Vertex Standard Co.,Ltd.5
RF Power Meter reading is 5 W (±0.5 W).
Press the [D/MR(MW)] key.
TX Deviation
Inject a 1 kHz, 50 mV signal from the Audio Generator.
Rotate the DIAL knob to set the alignment parameter to “145.000 dU.”
Press the [D/MR(MW)] key to enable adjustment of the “TX Deviation.”
Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the
Deviation Meter reading is 4.2 kHz (±0.1 kHz).
Press the [D/MR(MW)] key.
CTCSS TX Deviation
Rotate the DIAL knob to set the alignment parameter to “145.000 100.”
Press the [D/MR(MW)] key to enable adjustment of the “CTCSS TX Deviation.”
Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the
Deviation Meter reading is 0.6 kHz (±0.05 kHz).
Press the [D/MR(MW)] key.
DCS TX Deviation
Rotate the DIAL knob to set the alignment parameter to “145.000 dC.”
Press the [D/MR(MW)] key to enable adjustment of the “DCS TX Deviation.”
Press the PTT switch to activate the transmitter, adjust the DIAL knob so that the
Deviation Meter reading is 0.8 kHz (±0.05 kHz).
Press the [D/MR(MW)] key.
Closing the Alignment mode
Press the [DW(REV)] key to save the new setting and exit to normal operation.
Inhaltsverzeichnis
Andere Vertex Standard Transceiver Handbücher
Vertex Standard
Vertex Standard VXA-150 Referenzhandbuch
Vertex Standard
Vertex Standard VX-800 Bedienungsanleitung
Vertex Standard
Vertex Standard VX-6000V Bedienungsanleitung
Vertex Standard
Vertex Standard VX-450 series Bedienungsanleitung
Vertex Standard
Vertex Standard VX-4200 Series Bedienungsanleitung
Vertex Standard
Vertex Standard VX-146 Bedienungsanleitung
Vertex Standard
Vertex Standard EVX-5300 Bedienungsanleitung
Vertex Standard
Vertex Standard VX-510 Series Bedienungsanleitung
Vertex Standard
Vertex Standard VX-2100 Series Bedienungsanleitung
Vertex Standard
Vertex Standard VX-180U Bedienungsanleitung
Vertex Standard
Vertex Standard FT-8800R Bedienungsanleitung
Vertex Standard
Vertex Standard VXR-7000 Bedienungsanleitung
Vertex Standard
Vertex Standard VX-7200 Bedienungsanleitung
Vertex Standard
Vertex Standard VX-4107 Bedienungsanleitung
Vertex Standard
Vertex Standard VX-1210 Bedienungsanleitung
Vertex Standard
Vertex Standard VX-2000V Bedienungsanleitung
Vertex Standard
Vertex Standard Pilot VXA-210 Bedienungsanleitung
Vertex Standard
Vertex Standard VX-6000V Bedienungsanleitung
Vertex Standard
Vertex Standard Pilot III Bedienungsanleitung
Vertex Standard
Vertex Standard VX-1700 Series Bedienungsanleitung
