Vertical IP8012 Bedienungsanleitung
IP8000 Remote Phone
Configuration Guide
Release 3.5
June 2010
Release 3.5
June 2010
THIS PAGE INTENTIONALLY LEFT BLANK
SBX IP - IP8000 Phone Configuration Guide
Supported IP Phones page - 1
Remote Phone Set Up Instructions
Remote Phone Set Up Instructions
This document provides the following information about the set up of IP8000 on the SBX IP:
Supported IP Phones
• IP8012 and IP8024
• NomadIP Wireless
• Nomad SP Soft Phone
NOTE:This guide is specifically for setting up IP8000 series telephones.
Minimum Requirements
System
• SBX IP system with VOIP card
• Static IP address for VOIP card. If NAT is used, it must be a 1-to-1 NAT.
• Separate IP address for the KSU’s LAN port for system administration
NOTE:No VoIP communication takes place on the KSU LAN port
• SBX KSU software version 3.5aG or higher
• VOIP card software version B.1Dq
Installed Environment
• CAT5E or higher patch cords from VoIP car to LAN switch
• No hubs
• Adequate bandwidth for the anticipated number of H.323 VoIP calls.
Release 3.5
June 2010
IP Endpoint Licensing page - 2
Remote Phone Set Up Instructions
SBX IP - IP8000 Phone Configuration Guide
IP Endpoint Licensing
Nomad SP requires a per-seat license. Two seats are automatically included. You do not have
to install activation codes for these two seats.
• IP8000 series and NomadIP wireless phones require no license.
NOTE:Entering IP address information to the KSU database from a digital phone is performed differently
from programming IP settings in an IP remote phone.
Digital Keyset on the KSU
Enter digits in groups of three, with no punctuation or decimal.
EXAMPLE:
To program the address 192.168.1.3, dial
192168001001
> Save
IP Phone
Enter digits with an asterisk [] as the decimal.
EXAMPLE:
To program the address 192.168.1.10, dial
192*168*1*10
> Save
IP Addressing
To begin, you will need to:
1. Obtain IP addresses from the network administrator for the location in which you are
setting up the SBX IP system.
2. Make a note here of the information gathered above for reference while programming
the system.
VoIP card
(VOIB)
KSU LAN Port IP Phone
(may be DHCP)
Your PC
(may be DHCP)
IP Address
Subnet Mask
Default Gateway
Release 3.5
June 2010
SBX IP - IP8000 Phone Configuration Guide
IP Endpoint Licensing page - 3
Remote Phone Set Up Instructions
• You will also need a 24-button SBX digital telephone to set up the system.
• For a typical test-bench or demonstration setup, you need four connections to a LAN
switch: each via a straight-through CAT5E patch cord as shown above.
• You may use the following IP addressing information to set up a closed demo of the IP
phone.
NOTE:These addresses will not function in a wide-area network or the Internet, they are for testing
and demonstration purposes only.
VoIP Card KSU LAN Port IP Phone Your PC
IP Address 192.168.1.4 192.168.1.3 192.168.1.5 192.168.1.2
Subnet Mask 255.255.255.0 255.255.255.0 255.255.255.0 255.255.255.0
Default Gateway 192.168.1.1 192.168.1.1 192.168.1.1 192.168.1.1
Release 3.5
June 2010
Preparation page - 4
Remote Phone Set Up Instructions
SBX IP - IP8000 Phone Configuration Guide
Preparation
Before starting:
1. Verify that your VOIP card is installed into the system properly and that the card is
recognized in the KSU database.
NOTE:KSU DIP switches must be set to enable the system to retain programming
changes.
2. Set your PC IP address, default gateway, and subnet mask as shown in the table
above.
3. Set the KSU’s IP addressing using PGM 108 when logged into KSU administration
from the 24-button digital attendant station (station 100 by default).
• This assigns the IP address to the KSU’s LAN port.
• The configuration for the VOIP card begins here.
PCAdmin Connection
Follow the PCAdmin User’s Guide or the Tech Tip regarding setting up PCAdmin to establish
connection to the SBX system from PCAdmin on your PC.
NOTE:Remember that when connecting to the SBX using a LAN switch, a straight-through patch
cable, not a crossover cable, is required.
Configuring the VoIP Card Using PCAdmin
NOTE:Digital phone-based programming is shown on page 2.
1. Double-click Pre-programmedXConfiguration.
Release 3.5
June 2010
SBX IP - IP8000 Phone Configuration Guide
Configuring the VoIP Card Using PCAdmin page - 5
Remote Phone Set Up Instructions
2. Right-click on VoIB, then select Logical Assignment.
In Logical Assignments:
3. Right-click VoIB and Select (Virtual VoIB)XAppend to Station. A notation of 99 will be
entered in the STA Board field. Click Update when finished.
Î
Release 3.5
June 2010
Configuring the VoIP Card Using PCAdmin page - 6
Remote Phone Set Up Instructions
SBX IP - IP8000 Phone Configuration Guide
In VoIB Gateway:
4. Go to VoIB Gatekeeper Settings, then enter the IP Address, Default Gateway and
Subnet Mask that you are assigning to the VOIP card per the worksheet on page 2 of
this document. Then click Update.
In RSG IP Programming:
5. Double-click [VoIB Slot for RSG/IP].
6. Select the VoIB card (10), then click the >button sign.
Î.
• You will now see the card slot appear on the right. Click Update.
Release 3.5
June 2010
SBX IP - IP8000 Phone Configuration Guide
Configuring the VoIP Card Using PCAdmin page - 7
Remote Phone Set Up Instructions
From the VoIB Slot dropdown:
7. Select the card.
From the Channel Number dropdown:
8. Select 2 for the number of channels to be used for IP Phones.
9. Click Update Channel.
From the IP Phone Number dropdown
10. Select the 2, then click Update Num. This tells the system to assign 2 IP stations.
Release 3.5
June 2010
Configuring the VoIP Card Using PCAdmin page - 8
Remote Phone Set Up Instructions
SBX IP - IP8000 Phone Configuration Guide
11. Click Update.
12. Reset the KSU.
13. Double-click RSG/IP Programming > IP Phone Attributes.
14. Double-click on bin #1 (row #1), then enter the MAC address (which you will find
labeled on the bottom of the IP phone).
Release 3.5
June 2010
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Vertical IP-Telefon Handbücher
Vertical
Vertical SUMMIT IP Bedienungs- und Montageanleitung
Vertical
Vertical SUMMIT IP Bedienungsanleitung
Vertical
Vertical Xcelerator IP IP2007 Montage- und Bedienungsanleitung
Vertical
Vertical Xcelerator IP IP2007 Bedienungsanleitung
Vertical
Vertical Edge 120 Bedienungsanleitung
Vertical
Vertical SBX IP 320 Einrichtungshandbuch
Vertical
Vertical SBX IP 320 Bedienungsanleitung
Vertical
Vertical SBX IP 320 Bedienungsanleitung
Vertical
Vertical LDP-9030D Bedienungsanleitung
Vertical
Vertical SBX IP 320 Betriebsanleitung
Vertical
Vertical Edge 120 Bedienungsanleitung
Vertical
Vertical Xcelerator IP IP2007 Bedienungsanleitung
Vertical
Vertical Xcelerator IP2007 Bedienungsanleitung
Vertical
Vertical Xcelerator IP IP2007 Montage- und Bedienungsanleitung
Vertical
Vertical Edge 480i Service-Handbuch
Vertical
Vertical MBX IP Bedienungsanleitung
Vertical
Vertical Edge 5000 Bedienungsanleitung
Vertical
Vertical Xcelerator IP IP2007 Bedienungsanleitung
Vertical
Vertical Edge 5000i-LLCDG Bedienungsanleitung
Vertical
Vertical 9112i Bedienungsanleitung
