Vertiv Liebert GXT4 Series Montage- und Wartungsanleitung

Liebert®

GXT4™ UPS

Installer/User Guide

120V/208V, 500VA – 3000VA

Vertiv | Liebert® GXT4™ Installer/User Guide

Technical Support Site

If you encounter any installation or operational issues with your product, check the pertinent

section of this manual to see if the issue can be resolved by following outlined procedures.

Visit https://www.VertivCo.com/en-us/support/ for additional assistance.

The information contained in this document is subject to change

without notice and may not be suitable for all applications. While

every precaution has been taken to ensure the accuracy and

completeness of this document, Vertiv assumes no responsibility

and disclaims all liability for damages resulting from use of this

information or for any errors or omissions. Refer to other local

practices or building codes as applicable for the correct methods,

tools, and materials to be used in performing procedures not

specifically described in this document.

The products covered by this instruction manual are manufactured

and/or sold by Vertiv. This document is the property of Vertiv and

contains confidential and proprietary information owned by Vertiv.

Any copying, use or disclosure of it without the written permission

of Vertiv is strictly prohibited.

Names of companies and products are trademarks or registered

trademarks of the respective companies. Any questions regarding

usage of trademark names should be directed to the original

manufacturer.

TABLE OF CONTENTS

1 Important Safety Precautions 5

2 GXT4 Description 9

2.1 Features 9

2.2 Available Models 9

2.3 Front Panel and Controls 10

2.4 Rear Panel Features 10

2.5 Major Components 15

2.5.1 Transient Voltage Surge Suppression (TVSS) andEMI/RFIFilters 16

2.5.2 Rectifier/Power Factor Correction (PFC) Circuit 16

2.5.3 Inverter 16

2.5.4 Battery Charger 16

2.5.5 DC-to-DC Converter 17

2.5.6 Battery 17

2.5.7 Dynamic Bypass 17

2.5.8 Battery Cabinet 17

2.6 Operating Modes 18

2.6.1 Mains Mode 18

2.6.2 Manual Bypass Mode 18

2.6.3 Battery Mode 19

2.6.4 Battery Recharge Mode 19

2.6.5 Frequency Converter Mode 19

2.6.6 Active ECO Mode 19

3 Installation 21

3.1 What’s Included 21

3.2 Unpacking and Inspection 21

3.3 Preparation for Installation 21

3.3.1 Installation Environment 21

3.3.2 Installation Clearances 22

3.4 Installing the UPS 22

3.4.1 Tower Installation 22

3.4.2 Rack Installation 23

3.4.3 Connecting Cables 24

3.4.4 Connecting to AC Mains and Loads 24

3.4.5 Connecting Battery Cables 25

3.4.6 Connecting USB Communication Cables 25

3.4.7 Installing the Optional Liebert® IntelliSlot™ Card andCommunication Cables 25

4 Operation and Display Panel 27

4.1 LED Indicators 28

4.2 Control Buttons 28

4.3 LCD 28

Vertiv | Liebert® GXT4™ Installer/User Guide | 3

4.4 Menu Structure 29

4.4.1 Startup Screen 30

4.4.2 Default Screen 30

4.4.3 Main Menu Screen 30

4.5 Prompt List 33

4.6 Warning List 34

4.7 Fault List 34

5 Operation 37

5.1 Startup Checklist for the GXT4 37

5.2 Starting the UPS 37

5.3 Performing a Manual Battery Test 37

5.4 Performing Manual Bypass 38

5.5 Shutting Down the GXT4 38

5.6 Disconnecting Input Power from the GXT4 38

6 Communication 39

6.1 Liebert® IntelliSlot Communication Cards 39

6.2 USB Port Communication 39

6.2.1 Configuration Program 39

6.3 Terminal Block Communication 41

6.3.1 Any Mode Shutdown 41

6.3.2 Battery Mode Shutdown 42

6.3.3 On Battery 42

6.3.4 Low Battery 42

7 Maintenance 43

7.1 Replacing the Internal Battery Pack 43

7.1.1 Battery Replacement Procedures 44

7.2 Charging Batteries 46

7.3 Precautions 46

7.4 Checking UPS Status 46

7.5 Checking UPS Functions 47

8 Troubleshooting 49

8.1 Symptoms that Require Troubleshooting 49

8.1.1 Faults 49

8.1.2 Audible Alarm 50

8.2 Troubleshooting UPS Issues 50

9 Specifications 53

9.1 Auto-Learning Battery Run Times 60

Appendices 63

Appendix A: Technical Support 63

Vertiv | Liebert® GXT4™ Installer/User Guide | 4

1 IMPORTANT SAFETY PRECAUTIONS

SAVETHESEINSTRUCTIONS

This manual contains important safety instructions that must be followed during the installation and

maintenance of the UPS and batteries. Read this manual thoroughly before attempting to install or

operate this UPS.

UPS Safety Notes

This UPS contains no user-serviceable parts except the internal battery pack. The Off/Bypass

pushbutton does not electrically isolate internal parts. Under no circumstances attempt to gain internal

access other than to replace the batteries due to risk of electric shock or burn. Do not continue to use the

UPS if the front panel indications are not in accordance with these operating instructions or if the UPS

performance alters in use. Refer all faults to your local dealer, Vertiv representative or Vertiv Channel

Support.

This UPS has an internal battery, and the output receptacles of the UPS may carry live voltage even if the

UPS is not connected to utility input power.

Before moving or rewiring this UPS, disconnect utility input power and the battery and make sure that the

UPS is completely shut down. Otherwise, the output terminal may carry live voltage, presenting an electric

shock hazard.

To ensure human safety and normal UPS operation, the UPS must be properly grounded before use.

When the UPS is connected to an IT power distribution system, a short-circuit protection device must be

installed on the neutral line.

Install and use the Liebert® GXT4 in the following environments:

•Temperature: 32°F - 104°F (0°C - 40°C), relative humidity: 0% to 95% non-condensing

•Out of direct sunlight

•Away from heat sources

•Stable surface, not subject to vibrations or shocks

•Away from dust and other particulates

•Away from corrosive substances, salts and flammable gases

Keep the air inlet and outlet of this UPS unobstructed. Poor ventilation will increase the internal

temperature of the UPS and can adversely affect the UPS and its batteries.

Keep liquid and foreign objects away from the UPS.

In case of fire, use a dry chemical fire extinguisher to put out the fire. Using a fluid fire extinguisher may

cause electric shock.

This product is designed for commercial/industrial use only. This UPS is not intended for use with life

support and other designated critical devices. Maximum load must not exceed that shown on the UPS

rating label. This UPS is designed for data processing equipment. If uncertain, consult your local dealer or

Vertiv representative.

This UPS is not for use in a computer room as defined in the standard for the Protection of Electronic

Computer/Data Processing Equipment, ANSI/NFPA 75.

1 Important Safety Precautions 5

The Liebert® GXT4-3000RT120™was tested under 30A branch circuit in accordance with the National

Electrical Code, ANSI/NFPA 70. To reduce the risk of fire, connect only to a circuit provided with 30A

maximum branch over-current protection.

The Liebert® GXT4-3000RT208 was tested under 20A branch circuit in accordance with the National

Electrical Code, ANSI/NFPA 70. To reduce the risk of fire, connect only to a circuit provided with 20A

maximum branch over-current protection.

Battery Safety

WARNING! Risk of electric shock and explosion. Can cause equipment damage, injury and

death. Do not dispose of the battery in a fire. The battery may explode. Do not open or damage

the battery. Released electrolyte is toxic and is harmful to skin and eyes. If electrolyte comes

into contact with the skin, wash the affected area immediately with plenty of clean water and

get medical attention.

WARNING! Risk of electric shock. Can cause equipment damage, injury and death. A battery

can present a risk of electrical shock and high short-circuit current.

The following precautions should be observed when working on batteries:

•Remove watches, rings and other metal objects.

•Use tools with insulated handles.

•Wear rubber gloves and boots.

•Do not lay tools or metal parts on top of batteries.

•Disconnect charging source prior to connecting or disconnecting battery terminals.

•If the battery kit is damaged in any way or shows signs of leakage, contact your local Vertiv

representative immediately.

•Handle, transport and recycle batteries in accordance with local regulations.

•Determine if the battery is inadvertently grounded. If it is inadvertently grounded, remove the

source of the ground. Contact with any part of a grounded battery can result in electrical

shock. The likelihood of such shock will be reduced if grounds are removed during installation

and maintenance (applicable to a UPS and a remote battery supply not having a grounded

supply circuit).

ELECTROMAGNETIC COMPATIBILITY The Liebert® GXT4 series complies with the limits for a CLASS A

DIGITAL DEVICE, PURSUANT TO Part 15 of FCC rules. Operation is subject to the following conditions:

•This device may not cause harmful interference.

•This device must accept any interference received, including interference that may cause

undesired operation.

Operating this device in a residential area is likely to cause harmful interference that users must correct

at their own expense.

The Liebert® GXT4 series complies with the requirements of EMC Directive 2004/108/EC and the

published technical standards. Continued compliance requires installation in accordance with these

instructions and use of accessories approved by Vertiv.

Vertiv | Liebert® GXT4™ Installer/User Guide

Information for the Protection of the Environment

UPS Servicing: UPS makes use of components dangerous for the environment (electronic cards,

electronic components). The components removed must be taken to specialized collection and disposal

centers.

NOTICE TO EUROPEAN UNION CUSTOMERS: DISPOSAL OF OLD APPLIANCES—This product has been

supplied from an environmentally aware manufacturer that complies with the Waste Electrical and

Electronic Equipment (WEEE) Directive 2002/96/CE.

The “crossed-out wheelie bin” symbol at right is placed on this product to encourage you to recycle

wherever possible. Please be environmentally responsible and recycle this product through your

recycling facility at its end of life. Do not dispose of this product as unsorted municipal waste. Follow local

municipal waste ordinances for proper disposal provisions to reduce the environmental impact of waste

electrical and electronic equipment (WEEE). C

For information regarding the scrapping of this equipment, please browse

https://www.vertivco.com/en-emea/ or call our worldwide technical support.

•Toll Free: 00 80011554499

•Toll Number Based in Italy: +39 0298250222

SYMBOL DESCRIPTION SYMBOL DESCRIPTION

Risk of electrical shock Recycle

Indicates caution followed by important instructions DC voltage

AC input Equipment grounding conductor

AC output Bonded to ground

Requests the user to consult the manual AC voltage

Indicates the unit contains a valve-regulated lead acid battery

Table 1.1 Glossary of Symbols

1 Important Safety Precautions 7

Vertiv | Liebert® GXT4™ Installer/User Guide

This page intentionally left blank

2 GXT4 DESCRIPTION

The Liebert® GXT4 is a compact, online uninterruptible power system (UPS) that continuously conditions

and regulates its output voltage. The Liebert® GXT4 supplies microcomputers and other sensitive

equipment with clean sine-wave input power.

Upon generation, AC power is clean and stable. However, during transmission and distribution it is subject

to voltage sags, spikes, and complete failure that may interrupt computer operations, cause data loss, and

damage equipment.

The Liebert® GXT4 protects equipment from these disturbances. The Liebert® GXT4 continuously

charges its batteries from the utility power, enabling it to supply power to connected loads, even when the

mains fail.

2.1 Features

•Intelligent battery management to extend the battery life

•LCD for user-friendly operation and local monitoring and configuration of operational

parameters

•Controllable outlet groups

•Fan fault self-inspection and automated diagnostic function

•Intelligent fan operation, automatically changing rotation speed depending on system

requirements, to decrease power consumption and noise

•Input circuit breaker to ease recovery from overloads

•Safety approval from UL and cUL

•Communication options: USB port, Liebert® IntelliSlot™ port and terminal-block communication

•Dry contacts for remote monitoring

•Input power factor greater than0.99

•Output voltage selection function

2.2 Available Models

Available models of the UPS are listed in the following table.

MODEL NUMBER NOMINAL POWER RATING

GXT4-500RT120 500 VA/450 W

GXT4-700RT120 700 VA/630 W

GXT4-1000RT120 1000 VA/900 W

GXT4-1500RT120 1500 VA/1350 W

GXT4-2000RT120 2000 VA/1800 W

GXT4-3000RT120 3000 VA/2700 W

GXT4-3000RT208 3000 VA/2700 W

Table 2.1 UPS models, power ratings

2 GXT4 Description 9

2.3 Front Panel and Controls

The Liebert GXT4 rack/tower models in various power ratings have the same general appearance,

controls and features as shown in the following figure. The various rack/tower and minitower models differ

largely in the type of receptacles each has.

Figure 2.1 Front view

NO. DESCRIPTION

1 Ventilation slots

2 Operation and display panel

2.4 Rear Panel Features

The rear panel of the Liebert® GXT4 has these features:

•Liebert® IntelliSlot™ Port

•USB port

•Input Circuit Breaker

•Input Receptacle

•General Output Receptacles

•Programmable Output Receptacles

•Cable Strain-relief Attachment Hole

•External Battery Connector

•Cooling Fan

•RS-232 port

•Terminal Block Communication

•Output Circuit Breakers (only on 3000VA models)

Vertiv | Liebert® GXT4™ Installer/User Guide

Andere Handbücher für Liebert GXT4 Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vertiv UPS Handbücher

Vertiv

Vertiv Liebert EXM Bedienungsanleitung

Vertiv

Vertiv LIEBERT GXT5-6000IRT5UXL Bedienungsanleitung

Vertiv

Vertiv GXT4-5000RT230 Montage- und Wartungsanleitung

Vertiv

Vertiv Liebert GXT MT+ EX 1-3 kVA Bedienungsanleitung

Vertiv

Vertiv Liebert EXM Bedienungsanleitung

Vertiv

Vertiv Liebert GXT5 Montage- und Wartungsanleitung

Vertiv

Vertiv Liebert EXM2 Bedienungsanleitung

Vertiv

Vertiv Liebert CW Series Benutzerhandbuch

Vertiv

Vertiv Liebert NXL Bedienungsanleitung

Vertiv

Vertiv Liebert NXL Series Bedienungsanleitung

Vertiv

Vertiv Liebert PST5 Series Montage- und Wartungsanleitung

Vertiv

Vertiv Liebert EXM Bedienungsanleitung

Vertiv

Vertiv LIEBERT NXC 60KVA Montage- und Wartungsanleitung

Vertiv

Vertiv LIEBERT PSI5 Series Bedienungsanleitung

Vertiv

Vertiv Liebert EXM TXC Bedienungsanleitung

Vertiv

Vertiv Liebert GXT5-8000HVRT5UXLN Bedienungsanleitung

Vertiv

Vertiv Liebert GXT4 Series Bedienungsanleitung

Vertiv

Vertiv Liebert GXT5-500LVRT2UXL Bedienungsanleitung

Vertiv

Vertiv PSA4-1000MT120 Montage- und Wartungsanleitung

Vertiv

Vertiv Liebert ITA2 Bedienungsanleitung

Vertiv

Vertiv NetSure 48 Series Bedienungsanleitung

Vertiv

Vertiv Liebert NXL Bedienungsanleitung

Vertiv

Vertiv Liebert GXT5 Bedienungsanleitung

Vertiv

Vertiv Liebert PSA Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mecer

Mecer ME-1000-WTU Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung