Vertiv Liebert ITA2 Montage- und Wartungsanleitung

Liebert® ITA2

Installer/User Guide

8 - 10kVA, 60Hz, 208/220V

Vertiv™ | Liebert® ITA2 Battery Cabinet Installer/User Guide

Technical Support Site

If you encounter any installation or operational issues with your product, check the pertinent section of this

manual to see if the issue can be resolved by following outlined procedures.

Visit https://www.Vertiv.com/en-us/support/ for additional assistance.

The information contained in this document is subject to change without notice

and may not be suitable for all applications. While every precaution has been

taken to ensure the accuracy and completeness of this document, Vertiv

assumes no responsibility and disclaims all liability for damages resulting from

use of this information or for any errors or omissions. Refer to other local

practices or building codes as applicable for the correct methods, tools, and

materials to be used in performing procedures not specifically described in this

document.

The products covered by this instruction manual are manufactured and/or sold

by Vertiv. This document is the property of Vertiv and contains confidential

and proprietary information owned by Vertiv. Any copying, use or disclosure of

it without the written permission of Vertiv is strictly prohibited.

Names of companies and products are trademarks or registered trademarks of

the respective companies. Any questions regarding usage of trademark names

should be directed to the original manufacturer.

TABLE OF CONTENTS

Important Safety Information 1

1 Product Description 3

1.1 Rear Panel Components 4

2 Installation 5

2.1 Pre-Installation Preparation 5

2.1.1 Environment of Installation Area 5

2.1.2 Installation Clearances 6

2.1.3 Installation Tools 6

2.2 Equipment Handling and Unpacking 6

2.3 Attaching and Removing the Bezel 6

2.4 Tower Installation 7

2.5 Rack Installation 8

2.6 Connecting a Single Battery Cabinet System 10

2.6.1 Connecting the Cables 10

2.7 Connecting Additional Battery Cabinet Systems 16

3 Specifications 19

Vertiv™ | Liebert® ITA2 Battery Cabinet Installer/User Guide

This page intentionally left blank

IMPORTANT SAFETY INFORMATION

IMPORTANT! This manual contains important safety instructions that must be followed during the installation and

maintenance of the UPS and batteries. Read this manual thoroughly and the safety and regulatory information,

available at https://www.vertiv.com/ComplianceRegulatoryInfo, before attempting to install, connect to supply, or

operate this UPS and equipment.

Vertiv™ | Liebert® ITA2 Battery Cabinet Installer/User Guide

This page intentionally left blank

1 PRODUCT DESCRIPTION

The Vertiv™ Liebert® ITA2 battery cabinet provides DC input power the Liebert ITA2 UPS. The battery cabinet may be

installed in a rack or tower configuration, and a maximum of five battery strings can be connected to the UPS.

When introduced, the battery cabinet was 3U height (U = rack units). Later, to reduce the rack space required by a Liebert

ITA2 UPS system, the battery cabinet was replaced by a 2U cabinet.

1 Product Description 3

1.1 Rear Panel Components

Figure 1.1 3U Battery Cabinet Rear Panel

Item Description

1 RJ-45 communication port (x2)

2 Battery Port A

3 Battery output breaker

4 Battery Port B

Figure 1.2 2U Battery Cabinet Rear Panel

Item Description

1 DIPswitch

2 Battery output breaker

3 RJ-45 communication port (x2)

4 Battery Port B

5 Battery Port A

Vertiv™ | Liebert® ITA2 Battery Cabinet Installer/User Guide

2 INSTALLATION

Installation must be performed by properly trained and qualified personnel. Do not start the UPS until after the installation is

finished and the system is commissioned by an authorized engineer.

WARNING! Risk of electrical shock. Can cause property damage, injury, and death. The unit has several

circuits that are energized with high DC and AC voltages. Check for voltage with both AC and DC voltmeters

before making contact and before working within the UPS. Only properly trained and qualified personnel

wearing appropriate, OSHA-approved personal protective equipment (PPE) should prepare for installation,

install and maintain the equipment. When performing maintenance with any part of the equipment under

power, service personnel and test equipment must stand on rubber mats.

WARNING! Risk of electrical shock. Can cause equipment damage, injury and death. Before beginning

installation, verify that all external overcurrent protection devices are open (Off), and that they are locked out

and tagged appropriately to prevent activation during the installation. After the power cables are connected,

the terminal block’s protective cover must be reinstalled to remove the electric shock hazard.

WARNING! Risk of heavy unit falling. Improper handling can cause equipment damage, injury, and death.

Exercise extreme care when handling unit cabinets and rack-mounted units to avoid equipment damage or

injury to personnel. The battery cabinets weigh approximately 115lb.(52.2kg).

2.1 Pre-Installation Preparation

Before beginning the installation, consider the environmental requirements, service clearances and external protective

devices for installing the equipment.

2.1.1 Environment of Installation Area

Install the UPS battery cabinet in an environment with the ambient temperature within the specifications listed in Table 2.1

below.

The environment must:

•Be clean and well-ventilated.

•Have no direct sunlight on the system.

•Be free from water, heat source and flammable and explosive substances.

•Be free from dust, volatile gases and corrosive materials.

Environmental Conditions Range

Operating Temperature, °F (°C) 32~122 (0 ~ 50)

Storage Temperature, °F (°C) -13 ~ 122) (-25 ~ 50)

Relative Humidity 5%RH ~ 95%RH (non-condensing)

Altitude, ft. (m) 9800 (3000), no derating

Table 2.1 Battery Cabinet Environmental Conditions

2 Installation 5

2.1.2 Installation Clearances

Maintain at least 4in.(102mm) clearance at the front, rear and side of the battery cabinet. Do not obstruct the air inlets on

the front panel and rear panels. Blocking the air inlets reduces ventilation and heat dissipation, shortening the service life of

the unit.

2.1.3 Installation Tools

IMPORTANT! All tools used to install and maintain the Liebert ITA2 battery cabinet and equipment must be

insulated.

The following tools are required to properly install your battery cabinet:

•Phillips-head screwdriver to install the rack rails

•Flat-blade screwdriver to install the battery cable

2.2 Equipment Handling and Unpacking

WARNING! Risk of heavy unit falling. Improper handling can cause equipment damage, injury, and death.

Exercise extreme care when handling unit cabinets and rack-mounted units to avoid equipment damage or

injury to personnel. The battery cabinets weigh approximately 115lb.(52.2kg).

During unpacking:

•Inspect the UPS for damage. If you find any problem, file a damage claim with the carrier immediately and

send a copy to Vertiv.

•Check the accessories and model numbers against the delivery list. If you find any problem, notify your local

Vertiv representative immediately.

2.3 Attaching and Removing the Bezel

To attach the bezel:

1. Obtain the bezel from the accessories package, and align the bezel with the front panel of the battery cabinet,

see Figure 2.1 on the facing page.

2. Press the fittings on both sides of the bezel into the rectangular holes on the battery cabinet.

To remove the bezel, grasp the sides and pull it away from the cabinet.

Vertiv™ | Liebert® ITA2 Battery Cabinet Installer/User Guide

Andere Handbücher für Liebert ITA2

Inhaltsverzeichnis

Andere Vertiv UPS Handbücher

Vertiv

Vertiv Liebert APM Plus Bedienungsanleitung

Vertiv

Vertiv Edge LI Series Bedienungsanleitung

Vertiv

Vertiv LIEBERT PSA-PH Bedienungsanleitung

Vertiv

Vertiv Liebert NXL Bedienungsanleitung

Vertiv

Vertiv Liebert EXL Bedienungsanleitung

Vertiv

Vertiv Liebert ITA2 Bedienungsanleitung

Vertiv

Vertiv Liebert PSA Bedienungsanleitung

Vertiv

Vertiv Liebert GXT MT+ CX 1K SB Bedienungsanleitung

Vertiv

Vertiv Liebert EXS Bedienungsanleitung

Vertiv

Vertiv Liebert EXS Montage- und Wartungsanleitung

Vertiv

Vertiv Liebert GXT4 Series Montage- und Wartungsanleitung

Vertiv

Vertiv Liebert GXT5 Bedienungsanleitung

Vertiv

Vertiv Liebert APM Bedienungsanleitung

Vertiv

Vertiv Liebert EXM Bedienungsanleitung

Vertiv

Vertiv Liebert EXM Bedienungsanleitung

Vertiv

Vertiv Liebert GXT5 Bedienungsanleitung

Vertiv

Vertiv Liebert PSA4 Montage- und Wartungsanleitung

Vertiv

Vertiv Liebert EXS 80kVA UPS Bedienungsanleitung

Vertiv

Vertiv Avocent HMXCC1-G2 Bedienungsanleitung

Vertiv

Vertiv Liebert NXL 500kVA Bedienungsanleitung

Vertiv

Vertiv Liebert GXT5 Montage- und Wartungsanleitung

Vertiv

Vertiv Liebert MicroPOD Montage- und Wartungsanleitung

Vertiv

Vertiv Liebert GXT4 Series Bedienungsanleitung

Vertiv

Vertiv Liebert EXM MBC Bedienungsanleitung

Beliebte UPS Handbücher anderer Marken

Pylontech

Pylontech Victron & Pylontech US5000 Bedienungsanleitung

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Bedienungsanleitung

Mustek

Mustek PowerMust 530(B) Plus Installations- und Betriebshandbuch

Emerson

Emerson Liebert NXL series Bedienungsanleitung

MAKELSAN

MAKELSAN BOXER SERIES Bedienungsanleitung

Block

Block PC-0524-400-0 Bedienungsanleitung

CyberPower

CyberPower CP585LCD Bedienungsanleitung

Eaton

Eaton 3S Montageanleitung

CyberPower

CyberPower Office Tower Series UPS 1000 Bedienungsanleitung

CyberPower

CyberPower BM100 Bedienungsanleitung

Best Power

Best Power 610 Bedienungsanleitung

Best Power

Best Power Unity/I UT3K Bedienungsanleitung

Mustek

Mustek PowerMust 400 Offline Bedienungsanleitung

Xantrex

Xantrex Trace 512 UR-UPS Bedienungsanleitung

Forza

Forza SL-1501UL Bedienungsanleitung

LEGRAND

LEGRAND keor 310081 Bedienungsanleitung

ABB

ABB Conceptpower DPA 500 Bedienungsanleitung

ZincFive

ZincFive BC Series Bedienungsanleitung