Vestax PDX-2000 Bedienungsanleitung

PDX-2000 MIDI MOD v2

I´m not be responsible in any way if you damage your turntable

during the installation!

This mod requires some knowhow about soldering.

If you have no experience with soldering and electronics please ask

someone who does to do the mod.

Contact me at contact@djbacktrack.com with any questions.

emove the ultrapitch fader knob

Flip over your turntable. If you don’t

have anything good to support it with

use beer-cans at the corners.

emove the 1 5 screws and pull

away the baseplate.

Disconnect all cables going to the

pitch-PCB.

emove the screws and remove the

PCB.

Position your fader as shown in the

picture and carefully bend the two

legs forward.

Solder the wires as shown in the

pictures. Use the included shrink

tube on the fader pins.

Put the fader back and resolder it to

the pitch-PCB.

emount the PCB.

Solder the wires like shown.

The top black cable is ground and

belongs with the power wire

harness( ed/Black).

Here comes the tricky part. Use the

included desoldering braid and

remove the solder on the points

markerd in the picture.(See here how

to use:

http://www.youtube.com/watch?v=Ac

bezX8TrOU).

If you have a desoldering pump use

that. Its much easier.(Go buy one. Its

a good investment.)

If you can´t get it free. Heat up the

points and pull gently until you can

remove the fader.

emove the slidefader.

Now solder in the other black and

pink cable (its twisted) like this to the

mainboiard PCB. On the pcb it reads

"TO SW33/45"

Mount the mod PCB. Put the washer

under the PCB and use the included

screw.

Solder the red cable to lamp socket

like shown. Make sure you dont

short it to ground

Connect the wires like shown in the

pictures.

125

1 : Pitchfader

2: Board PCB

3: MIDI

4: Button PCB

5: Power

3,4,5 will come in one 6pin connector.

You can place the

midi connector

where ever you

want. But a good

place is the

backplate

Using the mod

Hold 33 and 45 button for 3 seconds to switch between MIDI and

normal mode.

You will hear a slight click every time it switches mode.

The mod always starts in normal when you power on.

Andere Handbücher für PDX-2000

Inhaltsverzeichnis

Andere Vestax Drehscheibe Handbücher

Vestax

Vestax PDX-3000MKII Bedienungsanleitung

Vestax

Vestax PDT-5000 Bedienungsanleitung

Vestax

Vestax PDX-D3MKII Bedienungsanleitung

Vestax

Vestax CONTROLLER ONE Bedienungsanleitung

Vestax

Vestax PDX-8000 Bedienungsanleitung

Vestax

Vestax PDX-2000 Bedienungsanleitung

Vestax

Vestax PDX- a2 Kurzanleitung

Vestax

Vestax BDT-2500 Bedienungsanleitung

Vestax

Vestax PDX-2000 Kurzanleitung

Vestax

Vestax PDX-a1 Bedienungsanleitung

Vestax

Vestax PDX-a2S Bedienungsanleitung

Vestax

Vestax PDX-2300 Bedienungsanleitung

Vestax

Vestax PDX-2300MkII Pro Bedienungsanleitung

Vestax

Vestax HANDY TRAX USB Bedienungsanleitung

Vestax

Vestax PDX-3000 Bedienungsanleitung

Vestax

Vestax PDX-2000 Bedienungsanleitung

Vestax

Vestax WRX-2000 Installationsanleitung

Vestax

Vestax PDX-2000MkII Pro Bedienungsanleitung

Vestax

Vestax PDX-d3S Bedienungsanleitung

Vestax

Vestax PVT-e2 Bedienungsanleitung

Beliebte Drehscheibe Handbücher anderer Marken

Gemini

Gemini CDT-05 MKII Bedienungsanleitung

Rotel

Rotel RP-820 Bedienungsanleitung

Shuman

Shuman MC-250BT Bedienungsanleitung

Stanton

Stanton STR8-150 Bedienungsanleitung

Audio Technica

Audio Technica AT-LPW40WN Bedienungsanleitung

Crosley

Crosley McQueen CR7011-GY Bedienungsanleitung

auna

auna TT-Classic Plus Bedienungsanleitung

COMO AUDIO

COMO AUDIO Turntable Analog Bedienungsanleitung

Dual

Dual 1009 F Bedienungsanleitung

REED

REED Muse3C Bedienungsanleitung

AXIOMTEK

AXIOMTEK OPS883-H Series Bedienungsanleitung

Pioneer

Pioneer PL-71 Bedienungsanleitung

Denon

Denon DP-400 Bedienungsanleitung

Dual

Dual 504 Bedienungsanleitung

Audio-Techica

Audio-Techica AT-LP60XBT Bedienungsanleitung

Goldring

Goldring G99 Bedienungsanleitung

Acoustic Signature

Acoustic Signature Typhoon NEO Bedienungsanleitung

Bryston

Bryston BLP-1 Bedienungsanleitung