Vestfrost NFG 309 Technisches Handbuch
GLASS DOOR FREEZERS
MANUAL OF INSTRUCTIONS FOR USE AND INSTALLATION
2
CONTENTS
2. HOW TO USE THE
APPLIANCE
Check that the cabinet is undamaged. Please
report any damage immediately to your dealer.
Wash the cabinet and inner lining with a mild
unscented detergent and wipe it dry. Do not use
abrasive scouring powder, steel wool or similar
material. Connection to the electricity supply:
See head 7 and 8.
Operating panel. See fig. 5 page 5.
1.Thermostat knob.
2. Indicator for the connection to the electricity
supply (green).
3. Switch for light.
The thermostat knob is adjustable from 0 (stop)
to 7 (coldest). Find the position of the thermostat
which gives you the desired temperature. Start at
position 4.
The evaporator is automatically defrosted.The
defrost water is led to a tray on top of the com-
pressor where the water evaporates.
Only use an unscented detergent when cleaning
the cabinet inside.
Switch off the appliance and pull out the plug
when cleaning the cabinet.
The skirting board can be removed to facilitate a
vaccuum-cleaning of the floor. See fig. 1 page 5.
Remember to clean the evaporating tray.
1. Before starting the appliance.
2. How to use the appliance.
3. Maintenance.
4. Has the appliance stopped working?
5. Safety.
6. Technical data.
7. Installation.
8. Lighting fixture.
Defrosting
3. MAINTENANCE
1. BEFORE STARTING
THE APPLIANCE
3
4. HASTHE APPLIANCE
STOPPED WORKING? Before calling a repairman, check that
●The plug is properly plugged into the wall
socket.
●The fuse is intact.
●The power has not been cut off.
●All controls are correctly set.
●Do not open the cabinet when unneces-
sary.
Do not store explosive substances in the
cabinet, such as gas, cigarette lighters, petrol,
ether or similar. Scrapped cabinets may
become dangerous to children at play.
Therefore, remove the door or place the
scrapped cabinet in such a way that children
cannot enter it.
Never store liquids with carbon dioxide in the
freezing section.
This appliance meets the provisions of the
following directives: 89/336/EEC
(electromagnetic compatibility), 73/23/EEC
(electrical equipment designed for use within
certain voltage limits) as amended.
The rating plate which is placed inside the
appliance contains technical information
including model and serial numbers.
See the drawing on page 7.
1. Pull the screen to the left.
2. Pull down the right side of the screen and
take it out.
- Remove the strip - possibly with text - by
pulling it out of the tracks along the whole
length of the profile.
- The fluorescent tube can now be replaced.
The mounting is performed in reverse order.
The glow switch can now be replaced without
removing the screen.
5. SAFETY
7. LIGHTING FIXTURE
6. TECHNICAL DATA
4
Install the cabinet in a dry place and so that it is
not exposed to direct sunlight or any other source
of heat.
Place the cabinet in a level position.This is easily
achieved by adjusting the adjustable feet at the
front edge of the base.The cabinet must not rest
against a wall on its hinged side. When placing
the cabinet on a carpet or on a wooden floor you
should adjust it once more after some time as the
cabinet might settle in soft foundations.
If you want to build the appliance into a cupboard
you must consider 2 factors:
1. There must be a sufficient space above, behind
and beside the appliance. See fig. (2a), (2b)
and (2c) page 6.
2. There must be a sufficient space between the
appliance and the wall and the like at the hinge
side. Fig. (2d) page 6.
It is safest to place the earthed wall socket above
the appliance and at least 2.0 m above the floor.
Any local installation rules for appliances of this
kind must be observed.
During a storm the electricity supply might be cut
off.
You should be aware of this when installing the
appliance in weekend cottages or elsewhere
where you would not immediately observe that the
power has been cut off. Construction and details
in the accessories are subject to alteration without
previous notice.
8. INSTALLATION
NOTE
The installation of this upright must be carried out in consultation with an
electrician.You must not use extension leads or connect more appliances to the
same electricity supply bank.The power consumption is 20 amperes at the start.
The mains impedance must not exceed 1 volt/ampere and the voltage must not
be less than 200 volts at the starting moment.
It must be ensured that the heat from the compressor and the condenser can be
given off behind the upright.The minimum distance to the wall is 30 mm.
5
Fig. 1
Fig. 4
➭
➭
Mounting of lock
for one-door uprights
Fig. 5
6
Fig.2a
Fig.2d
Fig.2b
Fig.2c
Fig.2e
min.2000
1850
min.150
30
30
600
600
min.1040
600 648
30
10
7
95.63.327.08
Andere Handbücher für NFG 309
1
Inhaltsverzeichnis
Andere Vestfrost Gefrierschrank Handbücher
Vestfrost
Vestfrost VD200CFM Bedienungsanleitung
Vestfrost
Vestfrost SW 350 M Bedienungsanleitung
Vestfrost
Vestfrost VCF 11186 Bedienungsanleitung
Vestfrost
Vestfrost WV186F Bedienungsanleitung
Vestfrost
Vestfrost VLS 064 RF Bedienungsanleitung
Vestfrost
Vestfrost ULTF-37i Bedienungsanleitung
Vestfrost
Vestfrost IKG 205 Bedienungsanleitung
Vestfrost
Vestfrost VR-BF27912H1S Bedienungsanleitung
Vestfrost
Vestfrost VR-BS16501M0 Bedienungsanleitung
Vestfrost
Vestfrost CFS 344 Bedienungsanleitung
Vestfrost
Vestfrost VIF 10177 S NoFrost Bedienungsanleitung
Vestfrost
Vestfrost VIF 11177 S Bedienungsanleitung
Vestfrost
Vestfrost 30501 Bedienungsanleitung
Vestfrost
Vestfrost VF 20186 NoFrost Bedienungsanleitung
Vestfrost
Vestfrost CNF 289 WB Bedienungsanleitung
Vestfrost
Vestfrost VLS 064A RF AC Bedienungsanleitung
Vestfrost
Vestfrost VR-BF27952H1S Bedienungsanleitung
Vestfrost
Vestfrost VD 204 FW Bedienungsanleitung
Vestfrost
Vestfrost VLS 026 RF SDD Bedienungsanleitung
Vestfrost
Vestfrost NFG 309 Bedienungsanleitung
