Vestil MRR Series Bedienungsanleitung

rev. 7/12/2016

MRR & MPR Series.docx

VESTIL MANUFACTURING CORP.

2999 North Wayne Street, P.O. Box 507, Angola, IN

46703

Telephone: (260) 665-7586 -or-Toll Free (800) 348-0868

MRR- SERIES &MPR SERIES,MULTIPURPOSE RAMPS

INSTRUCTION MANUAL

MPR-2410

MPR-2313-G

MRR-2310

Receiving instructions:

After delivery, IMMEDIATELY remove the packaging from the product in a manner that preserves the packaging and

maintains the orientation of the product in the packaging; then inspect the product closely to determine whether it

sustained damage during transport. If damage is discovered during the inspection, immediately record a

complete description of the damage on the bill of lading. If the product is undamaged, discard the packaging.

Notes:

1) Compliance with laws, regulations, codes, and non-voluntary standards enforced in the location where the product is

used is exclusively the responsibility of the owner/end-user.

2) VESTIL is not liable for any injury or property damage that occurs as a consequence of failing to apply either: a) the

instructions in this manual; or b) information provided on labels affixed to the product. Neither is Vestil responsible for

any consequential damages sustained as a result of failing to exercise sound judgment while assembling, installing,

using or maintaining this product.

Table of Contents

Hazard identification: explanation of signal words…………………………………………………...……………..…….

Safety Guidelines……………………………………………………………………………………………………….........

Operation…………………………………………………………………………………………………...……….…………

Inspections & Maintenance………………………………………………………………………………………………….

Limited warranty…………………………………………………………………………………………………...…..……..

rev. 7/12/2016

MRR & MPR Series.docx

HAZARD IDENTIFICATION: explanation of signal words

This manual uses SIGNAL WORDS to indicate the likelihood of personal injuries, as well as the probable

seriousness of those injuries, if the product is misused in the ways described. Other signal words call attention to

uses of the product likely cause property damage.

The signal words used appear below along with the meaning of each word:

Each person who assembles, installs, uses, or maintains this product should read the entire manual and fully

understand the directions in advance. If after reading the manual you do not understand an instruction, ask

your supervisor or employer for clarification, because failure to adhere to the directions in this manual might

result in serious personal injury.

SAFETY GUIDELINES

Vestil diligently strives to identify foreseeable hazards associated with the use of its products. However, material

handling is inherently dangerous and no manual can address every conceivable risk. The end-user ultimately is

responsible for exercising sound judgment at all times.

Electrocution might result if any part of the product contacts electrified wires. Reduce the likelihood of

electrocution by applying common sense:

DO NOT contact electrified wires with any part of this device, your body, or clothing.

DO NOT use or store the product where contact with electrified wires is likely.

1. Always inspect the usage area before using the product & implement precautions that account for conditions.

If this product is used improperly or carelessly, the operator and/or bystanders might sustain serious

personal injuries or even be killed. To reduce the likelihood of injury:

Failure to read and understand the entire manual before assembling, installing, using or servicing the

product is a misuse of the product.

Read the manual to refresh your understanding of proper use and maintenance procedures.

DO NOT attempt to resolve any problem(s) with the product unless you are both authorized to do so and certain

that it will be safe to use afterwards.

DO NOT modify the product in any way UNLESS you first obtain written approval from Vestil. Unauthorized

modifications automatically void the Limited Warranty and might make the product unsafe to use.

DO NOT exceed the maximum rated load (see Label 287 on product).

Inspect the product before each use.

A. DO NOT use this product if the inspection reveals structural damage. Examples of structural damage

include, but are not limited to, the following: 1) Cracked, broken or significantly deformed load-bearing

members; 2) cracked welds; 3) missing or deformed safety chain/strap; 3) corrosion, severe wear, or other

condition that affects the ability of the product to support weight or itself. Replace each part that fails to

pass an inspection, and DO NOT use the product until it is fully restored to normal condition.

B. DO NOT use the product if any unusual noise or movement is observed. If a malfunction occurs, remove

the unit from service and notify your supervisor & maintenance personnel about the issue.

DO NOT use this device UNLESS all product labels (see “Label Placement Diagram”) are readable and

undamaged.

Proper use, maintenance, and storage are essential for this product to function properly.

oAlways use this product in accordance with the instructions in this manual and consistent with any training

relevant to machines, devices, etc. used in conjunction with this product.

oKeep the product clean & dry. Lubricate moving parts.

oFOR HYDRAULIC UNITS: Do not use brake fluid or jack oils in the hydraulic system. If oil is needed, use an anti-

wear hydraulic oil with a viscosity grade of 150 SUS at 100°F, (ISO 32 cSt @ 40°C), or Dexron transmission fluid.

oContact the manufacturer for MSDS information.

Identifies a hazardous situation which, if not avoided, WILL result in DEATH or

SERIOUS INJURY. Use of this signal word is limited to the most extreme situations.

Identifies a hazardous situation which, if not avoided, COULD result in DEATH or

SERIOUS INJURY.

Indicates a hazardous situation which, if not avoided, COULD result in MINOR or

MODERATE injury.

Identifies practices likely to result in product/property damage, such as operation that

might damage the product.

rev. 7/12/2016

MRR & MPR Series.docx

Operation

Ramp Application

Do not exceed the ramp’s load rating. The ramp would fail to perform and could result in

equipment damage or personal injury. Reference the Exploded Parts diagram below.

The floor surface should be smooth so the entire ramp sets firmly on the floor. The loads are

distributed across this surface. If the surface is not smooth, the load stresses in the ramp may

exceed the ramp’s capacity and break and result in equipment damage and/or personal injury.

If the ramp’s height and the step’s height need to be the same. A difference in height may result

in a user mis-stepping and result in equipment damage and/or personal injury.

Bridge Application

Do not exceed the bridge’s load rating. The bridge would fail to perform and could result in

equipment damage or personal injury. Reference the Exploded Parts diagram below.

The floor surface should be smooth so the entire bridge sets firmly on the floor. The loads are

distributed across this surface. If the surface is not smooth, the load stresses in the ramp may

exceed the ramp’s capacity and break and result in equipment damage and/or personal injury.

The bridge should not set on or compress the cords, pipe or object(s) being bridged. The objects

should move freely while bridge is in use to prevent their damage.

Curb

Ramp properly positioned

to curb or step

Curb

Ramp improperly positioned

to curb or step

Ramp below Curb

Ramp above Curb

Gap between Ramp and Curb

rev. 7/12/2016

MRR & MPR Series.docx

Exploded Parts Diagram and Bill of Materials

MPR Series

rev. 7/12/2016

MRR & MPR Series.docx

MRR Series

rev. 7/12/2016

MRR & MPR Series.docx

Inspections & Maintenance

Each Use:

Inspect the ramp for cracks, evidence of yields or stretch plastic/rubber.

Inspect the hardware for bridged ramps. The fasteners should be tight and secure to perform their function.

Inspect the bridge features. The walls should be undamaged so cords, pipes and objects can freely move while the

bridge is in use.

If rust is present on the bracket, prepare the surface and paint.

If rust is present on the fasteners, replace with new hardware.

rev. 7/12/2016

MRR & MPR Series.docx

LIMITED WARRANTY

Vestil Manufacturing Corporation (“Vestil”) warrants this product to be free of defects in material and workmanship

during the warranty period. Our warranty obligation is to provide a replacement for a defective original part if the part is

covered by the warranty, after we receive a proper request from the warrantee (you) for warranty service.

Who may request service?

Only a warrantee may request service. You are a warrantee if you purchased the product from Vestil or from an

authorized distributor AND Vestil has been fully paid.

What is an “original part”?

An original part is a part used to make the product as shipped to the warrantee.

What is a “proper request”?

A request for warranty service is proper if Vestil receives: 1) a photocopy of the Customer Invoice that displays the

shipping date; AND 2) a written request for warranty service including your name and phone number. Send requests

by any of the following methods:

Mail Fax Email

Vestil Manufacturing Corporation (260) 665-1339 [email protected]

2999 North Wayne Street, PO Box 507 Phone

Angola, IN 46703 (260) 665-7586

In the written request, list the parts believed to be defective and include the address where replacements should be

delivered.

What is covered under the warranty?

After Vestil receives your request for warranty service, an authorized representative will contact you to determine

whether your claim is covered by the warranty. Before providing warranty service, Vestil may require you to send the

entire product, or just the defective part or parts, to its facility in Angola, IN. The warranty covers defects in the

following original dynamic components: motors, hydraulic pumps, electronic controllers, switches and cylinders. It also

covers defects in original parts that wear under normal usage conditions (“wearing parts”): bearings, hoses, wheels,

seals, brushes, batteries, and the battery charger.

How long is the warranty period?

The warranty period for original components is 30 days. The warranty period begins on the date when Vestil ships the

product to the warrantee. If the product was purchased from an authorized distributor, the period begins when the

distributor ships the product. Vestil may extend the warranty period for products shipped from authorized distributors

by up to 30 days to account for shipping time.

If a defective part is covered by the warranty, what will Vestil do to correct the problem?

Vestil will provide an appropriate replacement for any covered part. An authorized representative of Vestil will contact

you to discuss your claim.

What is not covered by the warranty?

1. Labor;

2. Freight;

3. Occurrence of any of the following, which automatically voids the warranty:

Product misuse;

Negligent operation or repair;

Corrosion or use in corrosive environments;

Inadequate or improper maintenance;

Damage sustained during shipping;

Collisions or other incidental contacts causing damage to the product;

Unauthorized modifications: DO NOT modify the product IN ANY WAY without first receiving written

authorization from Vestil. Modification(s) might make the product unsafe to use or might cause excessive

and/or abnormal wear.

Do any other warranties apply to the product?

Vestil Manufacturing Corp. makes no other express warranties. All implied warranties are disclaimed to the extent

allowed by law. Any implied warranty not disclaimed is limited in scope to the terms of this Limited Warranty.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vestil Hebesystem Handbücher

Vestil

Vestil HDDL-55 Bedienungsanleitung

Vestil

Vestil EHLTD Series Bedienungsanleitung

Vestil

Vestil FTTM-2 Bedienungsanleitung

Vestil

Vestil BBL-4 Bedienungsanleitung

Vestil

Vestil MH-V10 Bedienungsanleitung

Vestil

Vestil EHLT-E Bedienungsanleitung

Vestil

Vestil HDD Series Bedienungsanleitung

Vestil

Vestil CYL-P Series Bedienungsanleitung

Vestil

Vestil VDL-22.5 Bedienungsanleitung

Vestil

Vestil VWS-770-AA Bedienungsanleitung

Vestil

Vestil CYL-P-LUG Series Bedienungsanleitung

Vestil

Vestil FDA-800 Bedienungsanleitung

Vestil

Vestil WP Series Bedienungsanleitung

Vestil

Vestil FLB-D Series Bedienungsanleitung

Vestil

Vestil S-FORK-4/6-RL Bedienungsanleitung

Vestil

Vestil FMDL Series Bedienungsanleitung

Vestil

Vestil EPC Series Bedienungsanleitung

Vestil

Vestil LM-Series Bedienungsanleitung

Vestil

Vestil SST-45 Kurzanleitung zur Einrichtung

Vestil

Vestil CYL-D-1-PN Bedienungsanleitung

Vestil

Vestil SE/HP Series Bedienungsanleitung

Vestil

Vestil HBD Series Bedienungsanleitung

Vestil

Vestil CART-600-S-HR Bedienungsanleitung

Vestil

Vestil FMDL Series Bedienungsanleitung

Beliebte Hebesystem Handbücher anderer Marken

morse

morse 82H-124 Bedienungsanleitung

Braun

Braun NL955 Series Bedienungsanleitung

haacon

haacon 1889.10 Bedienungsanleitung

Protekt

Protekt AT 252 Bedienungsanleitung

R. Beck Maschinenbau

R. Beck Maschinenbau HS 600 Bedienungsanleitung

Nova Technology International, LLC

Nova Technology International, LLC NAS Series Bedienungsanleitung

Genie

Genie Z-60/34 Bedienungsanleitung

Screen Technics

Screen Technics INTERFIT Vertical Up Lift Bedienungsanleitung

Mortuary Lift

Mortuary Lift ULTIMATE 1000 Bedienungsanleitung

Custom Equipment

Custom Equipment Hy-Brid 3 Series Programmierhandbuch

Custom Equipment

Custom Equipment Hy-Brid Lifts 2 Series Programmierhandbuch

Hy-Brid Lifts

Hy-Brid Lifts HB-P3.6 Programmierhandbuch

BERG

BERG BeNomic EasyLeaf Bedienungsanleitung

Powermate

Powermate LiftGate LG-3 Bedienungsanleitung

Snorkel

Snorkel TM12 Series Bedienungsanleitung

Terberg

Terberg OMNIDEKA Bedienungsanleitung

Harmar Mobility

Harmar Mobility AL625 Betriebsanleitung

Rotary

Rotary SPO16 Bedienungsanleitung