VEVOR RTP15WS115V Bedienungsanleitung

Technical Support and E-Warranty Certificate https://www.vevor.com/support

Ref Center Tank Pump

USER MANUAL

MODEL:RTP15WS115V/RTP24WS115V

We continue to be committed to provide you tools with competitive price.

"Save Half", "Half Price" or any other similar expressions used by us only represents an

estimate of savings you might benefit from buying certain tools with us compared to the major

top brands and doses not necessarily mean to cover all categories of tools offered by us. You

are kindly reminded to verify carefully when you are placing an order with us if you are

actually saving half in comparison with the top major brands.

- 1 -

MODEL:RTP15WS115V/RTP24WS115V

Have product questions? Need technical support? Please feel free to

CustomerService@vevor.com

NEED HELP? CONTACT US!

This is the original instruction, please read all manual instructions

carefully before operating. VEVOR reserves a clear interpretation of our

user manual. The appearance of the product shall be subject to the

product you received. Please forgive us that we won't inform you again if

there are any technology or software updates on our product.

REF CENTER TANK

PUMP

- 2 -

PACKAGE CONTENTS

Item

Quantity

Ref Center Tank Pump

20 ft flexible Pipe

Instruction Manual

SPECIFICATIONS

Model

RTP15WS115V

RTP24WS115V

Voltage/Frequency

AC115V/60Hz

Current

2.5A

Power

1/50HP

1/30HP

Flow

≥65GPH

≥100GPH

Lift

15ft

24ft

Inlet Diameter

1.0in

Outlet Diameter

0.4in

Water tank volume

1/2 gallon

INTRODUCTION

Your Ref Center Tank Pump is designed as an automatic condensate

removal pump for water dripping off an air conditioner evaporative coil. The

pump is controlled by a float/switch mechanism which turns the pump on

when approximately 2-1/4” of water collects in the tank and automatically

switches off when the tank drains to approximately 1-1/4”. The Ref center

pump you have purchased is of the highest quality workmanship and

material. It has been engineered to give you long and reliable service.

Refcenter pumps are carefully packaged, inspected, and tested to ensure

safe operation and delivery. When you receive your pump, examine it

carefully to determine that there are no broken or damaged parts that may

have occurred during shipment. If damage has occurred, make a notation

and notify the firm that you purchased the pump from. They will assist you

- 3 -

in replacement or repair if required.

READ INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO

INSTALL, OPERATE OR SERVICE THE REFCENTER PUMP. KNOW

THE PUMP APPLICATION, LIMITATIONS, AND POTENTIAL HAZARDS.

PROTECT YOURSELF AND OTHERS BY OBSERVING ALL SAFETY

INFORMATION. FAILURE TO COMPLY WITH INSTRUCTIONS COULD

RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE!

RETAIN INSTRUCTIONS FOR FUTURE REFERENCE. INSTALLATION

AND CONNECTIONS ARE TO BE MADE BY A QUALIFIED PERSON.

SAFETY GUIDELINES

WARNING

DO NOT USE TO PUMP FLAMMABLE OR EXPLOSIVE FLUIDS SUCH

AS GASOLINE, FUEL OIL, KEROSENE, ETC. DO NOT USE IT IN

EXPLOSIVE ATMOSPHERES. THE PUMP SHOULD BE USED WITH

LIOUIDS COMPATIBLE WITH PUMP COMPONENT MATERIALS.

DO NOT HANDLE THE PUMP WITH WET HANDS OR WHEN STANDING

ON A WET OR DAMP SURFACE OR IN WATER. THIS PUMP IS

SUPPLIED WITH A GROUNDING CONDUCTOR AND/OR

GROUNDING-TYPE ATTACHMENT PLUG. TO REDUCE THE RISK OF

ELECTRICAL SHOCK, BE CERTAIN THAT IT IS CONNECTED TO A

PROPERLY GROUNDED GROUNDING-TYPE RECEPTACLE.

IN ANY INSTALLATIONS WHERE PROPERTY DAMAGE AND/OR

PERSONAL INJURY MIGHT RESULT FROM AN INOPERATIVE OF

LEAKING PUMP DUE TO POWER OUTAGES, DISCHARGE LINE

BLOCKAGE, OR ANY OTHER REASON, A BACKUP SYSTEM(S)

AND/OR ALARM SHOULD BE USED.

SUPPORT PUMP AND PIPING WHEN ASSEMBLING AND WHEN

INSTALLED. FAILURE TO DO SO MAY CAUSE PIPING TO BREAK,

PUMP TO FAIL, MOTOR BEARING FAILURES, ETC.

- 4 -

INSTALLATION

1.Before installing the pump, allow the air conditioner to cycle several

times, collecting condensate in a separate container to help flush any

residual oils that may remain in the system.

2.Carefully unpack the pump. Remove the cardboard packing from the

motor cover air slots. Carefully slide the packing away from the pump. This

packing is used to prevent switch movement during shipment (Figure 1).

3.Mounting the pump: the tank has two slots provided to mount the unit.

The slots are located on the ends of the tank (Figure 5). The unit should be

mounted either on the side of the air conditioner unit or a nearby wall. The

pump must be level, and the inlet must be below the coil drain. Conduit

fittings are not compatible with the plastic pump housing.

4.The pump should not be installed in a manner that will subject it

tosplashing or spraying.

5. This pump is not intended for use inside air plenums.

ELECTRICAL CONNECTIONS

WARNING

1.Shut off the electrical power at fuse box before making any connections.

All wiring must comply with local codes.

2.Line voltage: Connect the power cord to the line voltage specified on the

motor and nameplate. The power cord must be connected to a constant

source of power (not a fan or other device that runs intermittently). If the

power cord does not have a plug, wiring is as follows: green (or

green/yellow)-ground. Black (or brown)-line. White (or blue)-neutral.

3.Safety switch: The safety overflow switch should be connected to a class

- 5 -

II low-voltage circuit. To control a thermostatic circuit, the COM and NO

connections from the safety switch are to be wired in series with the

low-voltage thermostat circuit to shut down the heating/AC circuit. The

COM and NC switch contacts may be used to actuate a low-voltage alarm

circuit (connected in series) if the heating/cooling system cannot be

disrupted. The safety switch comes from the factory with leads connected

to the COM and NO switch terminals. Typical hook-up of “NC” circuits

would be (Figures 2 & 3),

- 6 -

PIPING

1.Run flexible tubing or pipe from the evaporator drain into one of the three

pump inlets. Be sure inlet piping is sloped downward to allow gravity flow

(Figure 4). Extend the inlet piping into the tank from 1 to 3 inches to ensure

that it will not interfere with proper float operation. Be sure that the inlet

piping is cut at an angle where it enters the tank.

2.The outlet piping should be flexible tubing secured with a hose Clamp

(not provided) or pipe (3/8 inch ID. maximum to prevent excessive flow

back to the unit). From the condensate unit, extend the discharge piping

straight up as high as necessary. Do not extend this line above the

head/GPH of the particular model being installed. From this high point,

slope the discharge line down slightly to a point above the drain area, then

turn down and extend to a point below or approximately level with the

- 7 -

bottom of the condensate unit. This will give a siphoning effect which will

improve the efficiency of the condensate unit and will, in most cases,

eliminate the need for a check valve (Figure 5). If it is not possible to slope

the discharge line down, make an inverted “U” trap directly above the pump

at the highest point.

SERVICE INSTRUCTIONS

WARNING

1.Make certain that the unit is disconnected from the power source

before attempting to service or remove any component!

2.Be sure the floats move freely. Clean as necessary (Figure 6).

3.Clean the tank with warm water and mild soap.

4. Check the inlet and outlet piping. Clean as necessary. Be sure there are

no kinks in the line that would inhibit flow.

- 8 -

TESTING

1. Turn on the power.

2. Remove the motor/tank cover assembly and hold level.

3. Test the motor switch by raising the motor switch float with a finger

(Figure 6). The motor should turn on just before the float contacts cover.

4. Test the safety switch by raising the safety switch float with a finger. The

safety switch should activate before the float contacts cover.

5. Replace the motor/tank cover assembly on the tank.

This pump is suitable for gas furnace condensate applications. Caution

must be taken to ensure the acidity of condensate does not increase below

the average pH of 3.4 (to prevent localized pocket of acid that acts like a

battery causing pitting) by routinely cleaning or flushing the tank with fresh

water.

LIMITED WARRANTY

Your product is guaranteed to be in perfect condition when it leaves our

factory. It is warranted against defective materials and workmanship for a

period of 12 months from the date of purchase by the user.

Any product that should fail for either of the above two reasons and is still

within the warranty period will be repaired or replaced at the option of the

Ref center. All defective products returned under warranty will be fully

inspected to determine the cause of failure before the warranty is

approved.

DISCLAIMER: THE FOREGOING WARRANTY IS AN EXCLUSIVE

WARRANTY IN LIEU OF ANY OTHER EXPRESS WARRANTIES. ANY

IMPLIED WARRANTIES (INCLUDING, BUT NOT LIMITED TO, ANY

IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE) TO THE EXTENT EITHER APPLIES TO A

PUMP SHALL BE LIMITED IN DURATION TO THE PERIODS OF THE

EXPRESS WARRANTIES GIVEN ABOVE.

- 9 -

Warranty will be VOID if any of the following conditions are found:

1.Sealed motor housing opened.

2.Product connected to a voltage other than indicated on the nameplate.

3.Cord cut off to a length of fewer than three feet.

4.Pump allowed to operate dry (fluid supply cut off).

5.Pump used to circulate anything other than water.

6.Product abuse by Customers.

Any oral statements about the product made by the seller, the

manufacturer, the representatives, or any other parties, do not constitute

warranties, shall not be relied upon by the user, and are not part of the

Contract for sale. The seller’s and manufacturer’s only obligation, and the

buyer’s only remedy, shall be the replacement and/or repair by the

manufacturer of the product as described above. NEITHER SELLER NOR

THE MANUFACTURER SHALL BE LIABLE FOR ANY INJURY, LOSS, OR

DAMAGE, DIRECT, INCIDENTAL, OR CONSEQUENTIAL (INCLUDING,

BUT NOT LIMITED TO, INCIDENTAL OR CONSEQUENTIAL DAMAGES

FOR LOST PROFITS, LOST SALES, INJURY TO PERSON OR

PROPERTY, OR ANY OTHER INCIDENTAL OR CONSEQUENTIAL

LOSS), ARISING OUT OF THE USE OR THE INABILITY TO USE THE

PRODUCT AND THE USER AGREES THAT NO OTHER REMEDY

SHALL BE AVAILABLE TO IT. Before using, the user shall determine the

suitability of the product for the intended use, and the user assumes all risk

and liability whatsoever in connection therewith.

Some states and Countries do not allow limitations on how long an implied

warranty lasts or the exclusion or limitation of incidental or consequential

damages, so the above limitations or exclusions may not apply to you. This

warranty gives you specific legal rights, and you may also have other rights

which vary from state to state and country to country.

*There are any minor changes to the numbers included in the user manual

without prior notice.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere VEVOR Wasserpumpe Handbücher

VEVOR

VEVOR YOILP-HG0015A Bedienungsanleitung

VEVOR

VEVOR YMK40107A Bedienungsanleitung

VEVOR

VEVOR AP-20A Bedienungsanleitung

VEVOR

VEVOR DC666-120V Bedienungsanleitung

VEVOR

VEVOR FLO500 Bedienungsanleitung

VEVOR

VEVOR 2KQ-2G Bedienungsanleitung

VEVOR

VEVOR KQ-1K Bedienungsanleitung

VEVOR

VEVOR KQ-1K Bedienungsanleitung

VEVOR

VEVOR JC15G-15 Bedienungsanleitung

VEVOR

VEVOR 15PBG-6A Bedienungsanleitung

VEVOR

VEVOR Q1CZ-800C1 Bedienungsanleitung

VEVOR

VEVOR VP245 Bedienungsanleitung

VEVOR

VEVOR KXD1810G Bedienungsanleitung

VEVOR

VEVOR FPY Series Bedienungsanleitung

VEVOR

VEVOR FLO700 Bedienungsanleitung

VEVOR

VEVOR PAS-30AC Bedienungsanleitung

VEVOR

VEVOR NMDPA33-G33-45-110 Bedienungsanleitung

VEVOR

VEVOR KQ-1K Bedienungsanleitung

VEVOR

VEVOR FLO300 Bedienungsanleitung

VEVOR

VEVOR VVPS215BUS Bedienungsanleitung

VEVOR

VEVOR NMDP52-G55-70-12 Bedienungsanleitung

VEVOR

VEVOR GYB-630B Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung

STA-RITE

STA-RITE ST33APP Bedienungsanleitung