Viavi E4100 Series Stücklistenhandbuch

VIAVI Solutions

Quick Card

T-BERD®/MTS-5800 Modular Test Set

E4100-series OTDR SMART TEST

This quick card describes how to connect to a fiber under test, configure SMART TEST OTDR settings,

run tests, and analyze results with a VIAVI T-BERD/MTS-5800 and 4100-series OTDR module.

Equipment Requirements:

•T-BERD/MTS-5800 equipped with the following:

oFiber Optics Software Release V17.22 or

greater

oE4100 Series OTDR Module

•Fiber optic cleaning and inspection tools

•Launch Cable with connectors matching the

OTDR port and Fiber Under Test (a 20-meter

Fiber optic patch cable or leash is recommended)

•Optical Coupler to connect Launch Cable to Fiber

Under Test

Figure 1: Equipment Requirements

The following information is required to complete the

test:

•Type of Fiber (Multimode or Single Mode)

•Type of Connectors (SC UPC, SC APC, LC UPC, etc.)

•Distance unit (feet, meters, miles, kilometers)

Fiber Inspection Guidelines:

•Use the VIAVI P5000i or FiberChek Probe

microscope to inspect both sides of every

connection being used (OTDR Port, Launch Cable,

bulkhead connectors, patch cords, etc.)

•Focus the fiber on the screen. If dirty, clean the

connector.

•If it appears clean, run inspection test.

•If it fails, clean the fiber and re-run inspection

test. Repeat until it passes.

Figure 2: Inspect Before You Connect (IBYC)

Connect Launch Cable to OTDR port:

1. Inspect the OTDR port on top of the test set.

2. Inspect the fiber end face of Launch Cable.

3. Connect Launch Cable to the OTDR port.

VIAVI Solutions

Launch and Configure Smart Test:

1. Press the Power button to start the test set.

2. Tap the Fiber Optics icon in the

Status Bar at the top of the screen.

3. Tap the Home icon to display the Home

view with the SMART TEST icon.

4. Tap the SMART TEST icon until it is yellow and

highlighted .

Figure 3: Fiber Optics Home screen

5. Select the Point_To_Point configuration file and

tap to view the SMART TEST Setup

screen.

Figure 4: SMART TEST Configuration File

6. Laser: Tap the desired wavelength(s) to test.

Select 2 wavelengths to detect bends. Selected

wavelength(s) will turn dark blue.

7. Distance Unit: Tap the desired unit of measure

for the launch cable.

8. Launch Cable:

•Tap YES if you are using a Launch Cable.

•Tap the icon to enter or measure the Launch

Cable length.

•If the launch cable length is known, tap to

clear existing text, enter new value on the keypad

and tap to return.

•To measure the launch cable length, tap Measure

and tap Confirm. The measured value will auto-

populate when measurement is finished.

•Note: The Launch Cable should not be connected

to the Fiber Under Test during measurement.

9. Alarms: Choose Default for Viavi recommended

Pass/Fail limits.

10.Distance Unit: If you wish to use a different unit of

measure for the test results, change the unit of

measure to the desired value.

Figure 5: SMART TEST Setup

Figure 6: Launch Cable Setup

VIAVI Solutions

Connect to Fiber Under Test (FUT):

The Launch Cable may be connected to the FUT

via an optical patch panel (OPP) or an optical

coupler:

1. If the interface to the FUT is a patch cord,

connect the patch cord to an optical coupler

with the same connector type.

2. Inspect the FUT connected to the coupler or OPP.

3. Inspect the other fiber end face of the Launch

Cable.

4. Connect the Launch Cable to the coupler or OPP.

Figure 7: Connecting the Launch Cable to the FUT with a coupler

Figure 8: Connecting the Launch Cable to an OPP

Run Test:

1. Tap to start the test. After auto-

configuration, the OTDR will perform a connection

check to ensure that the connection is Good. If the

Connection is Bad, disconnect the launch cable,

repeat steps 1 through 3 on page 1, and repeat

steps 1 through 4 above on page 3.

2. The T-BERD will perform acquisitions at the

configured wavelengths.

3. Results can be displayed in 2 different formats:

Trace view or SmartLink view. Tap to

toggle between views.

Figure 9: Connection Check

•SmartLink view: The FUT is displayed as a

series of icons representing each event

(connectors, splices, bends, etc.). The center

of the display shows summary results for the

entire span. Acquisitions for which all events

are acceptable are marked with a green check

.Acquisitions with events that exceed

pass/fail thresholds for loss or reflectance are

marked with a red . The lower display

shows each event that exceeds thresholds.

Softkeys can be used to alter the display:

•Tap any icon in the upper display to

show detailed results for the event.

•Detailed results are shown for all

events.

Figure 10: SmartLink View

VIAVI Solutions

(+1 844 468 4284)

To reach the VIAVI office nearest you,

visit viavisolutions.com/contacts.

Product specifications and descriptions in this

document are subject to change without notice.

•Trace view: Results for each wavelength are

shown in different colors in the top section of

the display. Each event is listed in the lower

section of the display. Any events that violate

pass/fail thresholds for loss or reflectance are

shown in RED.

Use the right and left arrow keys in the

control panel to Toggle between results for

each wavelength. Tap the Zoom soft key

to enable the following zoom controls:

•Toggle between automatic zoom and

full trace view

•Expand and contract trace.

Figure 11: Trace View

4. Tap the Save softkey to view File

Recording Information.

5. Enter Fiber Id, Fiber Number, Locations, and Job

ID as follows:

•Tap field to open keyboard

•Tap to clear existing text.

•Enter desired value.

•Tap icon to return.

Note: The Job ID field identifies the Job ID and

creates a folder to save the result by the same

name. The default save location is JOB folder

under disk.

6. Tap to save the OTDR trace in .sor

format. Tap to save OTDR trace in .sor

and .pdf format. One file is saved per

wavelength.

Figure 12: Recording Information

7. The T-BERD/MTS will return to the OTDR

results screen.

8. Tap the Assistant soft key to return to

the SMART TEST Setup menu.

9. Repeat all steps on pages 3 and 4 for all Fibers

under test.

Figure 13: SMART TEST Setup

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi OLP-88 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi CT-X Bedienungsanleitung

Viavi

Viavi OneExpert ONX CATV 620 Bedienungsanleitung

Viavi

Viavi OneAdvisor ONA-800 Stücklistenhandbuch

Viavi

Viavi 3900 Series Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi ONX-220 Bedienungsanleitung

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi IFR 6015 Bedienungsanleitung

Viavi

Viavi SmartClass FBP-OLP-82 Bedienungsanleitung

Viavi

Viavi 3900 Series Betriebsanleitung

Viavi

Viavi T-BIRD-4000 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS-5800 Stücklistenhandbuch

Viavi

Viavi SmartClass Fiber OLTS-85 Bedienungsanleitung

Viavi

Viavi 4100 Series Stücklistenhandbuch

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi 7200 Series Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 8000 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800-100G Stücklistenhandbuch

Viavi

Viavi OneExpert ONX CATV Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 2000 Bedienungsanleitung

Viavi

Viavi FBP-HD4i Bedienungsanleitung

Viavi

Viavi IFR 4000 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung