Viavi T-BERD MTS 5800 Stücklistenhandbuch

VIAVI Solutions

Quick Card

T-BERD®/MTS 5800 Network Tester

Ethernet Layer 3 IPv4 Traffic Loopback

This quick card describes how to set the T-BERD/MTS 5800 up as a Layer 3, IPv4 Loopback device.

Equipment Requirements:

•T-BERD/MTS 5800 equipped with the following:

oBERT software release V26.0 or greater

oEthernet test options:

▪C510M1GE for 10 Megabit to 1 Gigabit Ethernet

▪C510GELAN for 10 Gigabit Ethernet

▪C525GELAN for 25 Gigabit Ethernet

▪C540GELAN for 40 Gigabit Ethernet

▪C5100GELAN for 100 Gigabit Ethernet

oSFP, QSFP, or CFP4 optical transceiver to match the

line under test

•CAT5E cable or fiber optic Jumper cables to match the

optical transceiver and the line under test

•Fiber inspection microscope

(VIAVI P5000i or FiberChek Probe)

•Fiber optic cleaning supplies

Figure 1: Equipment Requirements

The following information is required to complete the test:

•Physical Interface (10/100/1000BASE-T, 1000BASE-LX, 10GBASE-LR, 100GBASE-LR4, etc.)

•Auto Negotiation settings of the port under test (if 1 Gigabit or below)

•Encapsulation (VLAN or None)

•VLAN ID (if Encapsulation = VLAN)

•Source IP Type (Static or DHCP)

•Source IP Address (if Source IP Type = Static)

•Subnet Mask (if Source IP Type = Static)

•Default Gateway (if Source IP Type = Static)

•Destination IP Address

Fiber Inspection Guidelines:

Inspect both sides of every fiber optic connection being used

(bulkhead connectors, patch cords, and SFP ports) prior to

reconnection for each test. Using the VIAVI P5000i or

FiberChek Probe microscope:

•Focus fiber on the screen. If dirty, clean the connector.

•If it appears clean, run inspection test.

•If it fails, clean the fiber and re-run inspection test. Repeat

until it passes.

Figure 2: FiberChek Probe

VIAVI Solutions

•To inspect SFP ports with the P5000i, insert the probe tip

into the SFP port, move the focus wheel all the way to one

end, and slowly move the focus wheel to the other end.

•To inspect SFP ports with the FiberChek Probe, manually

focus with middle toggle switch or pull the trigger to auto-

focus.

•If a fiber stub (a darker circle on a lighter background as

shown in figure 3) is detected, follow standard inspection

and cleaning procedures. If you are unable to focus on a

fiber end face, do not clean the port. The SFP contains a

lens and cannot be cleaned.

Figure 3: Image of Clean Fiber

Connect to Line Under Test:

1. For copper 10/100/1000BASE-T

testing with the T-BERD/MTS

5800v2, connect the Port 1

10/100/1000 RJ-45 jack to the port

under test using CAT 5E or better

cable.

2. For copper 10/100/1000BASE-T

testing with the T-BERD/MTS 5800-

100G, insert a copper SFP into the

Port 1 SFP+/SFP28 slot and connect

to the port under test using CAT 5E

or better cable.

Figure 4: T-BERD 5800v2 Dual Port mainframe

3. For optical interfaces:

•Insert desired SFP, QSFP, or

CFP4 into the Port 1 slot on the

top of the T-BERD/MTS.

•Inspect and, if necessary, clean

all SFPs, fibers, and bulkheads,

as described on page 1.

•Connect the SFP, QSFP, or CFP4

to the port under test using a

Single Mode or Multimode

jumper cable compatible with

the interface under test.

Figure 5: T-BERD 5800-100G mainframe

VIAVI Solutions

Launch and Configure Test:

1. Press the Power button to turn on the

test set.

2. Using the Select Test menu, Quick Launch

menu, or Job Manager, launch an Ethernet,

Layer 3 Traffic, IPv4, Terminate test on port

1 for the desired physical interface.

For example:

Ethernet►10/100/1000►Layer 3 Traffic

►IPv4►P1 Terminate.

3. If the test is not in the default setup, tap

the Tools icon , and select

Press to continue and wait for

test to reconfigure.

4. For 10/100/1000 Electrical and 1GigE

Optical tests, tap the Ethernet tab of the

Quick Configuration menu and set Auto

Neg. to the same value as the Ethernet port

under test.

5. For 1GigE, 10GigE, 25GigE, 40GigE, or

100GigE optical tests, select the Laser tab in

the Actions panel, and press . The

button will turn yellow and be relabeled

6. Press the Restart soft key , on the

right side of the screen.

7. A green Signal Present LED ●indicates the

T-BERD/MTS is receiving an optical signal

from the port under test. Green Sync

Acquired and Link Active LEDs indicate that

the T-BERD/MTS has successfully connected

to the port under test and the link is active.

VIAVI Solutions

(+1 844 468 4284)

To reach the VIAVI office nearest you,

visit viavisolutions.com/contacts.

Product specifications and descriptions in this

document are subject to change without notice.

8. Press the Setup soft key , and select

the Ethernet settings tab. If a VLAN is

present, set Encapsulation to VLAN, tap the

VLAN field, and enter the VLAN ID.

9. Select the IP settings tab and tap the

Source/Destination Address field. Enter

the Source IP Type (Static or DHCP). If

Static, enter the Source IP address, Subnet

Mask, and Default Gateway.

10. Set Destination Address to the IP Address

of the T-BERD/MTS traffic generator,

running the Layer 3 Traffic, RFC-2544, or

Y.1564 SAMComplete test. Tap the PING

button to verify IP connectivity.

11. Press the Results Soft Key , to view

the progress of the test.

Andere Handbücher für T-BERD MTS 5800

Inhaltsverzeichnis

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi OneAdvisor 800 Platform Bedienungsanleitung

Viavi

Viavi OneAdvisor ONA-1000 400G Technisches Handbuch

Viavi

Viavi P5000i Bedienungsanleitung

Viavi

Viavi COSA-4055 Stücklistenhandbuch

Viavi

Viavi SmartClass Fiber MPOLx Stücklistenhandbuch

Viavi

Viavi CT-X Bedienungsanleitung

Viavi

Viavi HST-3000 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi NSC-100 Bedienungsanleitung

Viavi

Viavi AVX-10K Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi HST-3000 Stücklistenhandbuch

Viavi

Viavi IFR 6015 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-2000 Stücklistenhandbuch

Viavi

Viavi IFR 6000 Bedienungsanleitung

Viavi

Viavi ATC-5000NG Bedienungsanleitung

Viavi

Viavi IFR 6000 Bedienungsanleitung

Viavi

Viavi MTS 2000 Bedienungsanleitung

Viavi

Viavi 7200 Series Betriebsanleitung

Viavi

Viavi FBP-HD4i Bedienungsanleitung

Viavi

Viavi IFR 4000 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS 4000 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung