Viavi OneAdvisor 1000 Bedienungsanleitung

VIAVI//Public

OneAdvisor 1000 High-Speed Network Testing Platform

QUICK CARD

DS3 Bit Error Rate Testing (BERT)

This quick card describes how to configure and run a DS3 Bit Error Rate Test to a hard

loop, or another similarly configured VIAVI Test Instrument.

•OneAdvisor 1000 equipped with the following:

o100G Transport Module

oBERT software release V30.1.0 or greater

oC5DS3STS1 test option: DS3/STS-1 Electrical

oC5DUALPORT test option

•Two (2) mini-BNC to BNC adapters (CB-MINITOBNCQTY1)

•One of the following DS3 cable sets to connect the

T-BERD 5800 DS3 Port(s) to the line under test:

oTwo (2) BNC to BNC cables (CB-30662)

oTwo (2) BNC to WECO 440Acables (CB-015837) Figure 1: Equipment Requirements

LAUNCH TEST

1. Press the Power button to turn on the

OneAdvisor.

2. Press the 100G Module Test icon

at the top of the screen.

3. Tap the Power button and click

to launch the 100G Module.

4. Using the Select Test menu, Quick Launch

menu, or Job Manager, launch the

DS1/DS3►DS3►DS3 BERT►Terminate

test.

Figure 2: Launch 100G Module

Figure 3: Launch Test

VIAVI//Public

OneAdvisor 1000 High-Speed Network Testing Platform

QUICK CARD

•The following Information is needed to

configure the test:

•DS3 Framing (C-BIT or M13)

•Clock Source (Internal or Recovered)

•Test Patterns(s)

•BER Pass/Fail Threshold

1. Tap to open the Tools Panel and

select .

2. Press to continue.

3. Press the Setup soft key on the top right

side of the screen.

4. Select the indicated folders and configure

your test as follows. Leave all other values at

default, unless specified in the work order.

5. Press the Results soft key to view the

Test Results screen.

Figure 4: Work Order

CONFIGURE TEST

Folder

Option

Value(s)

Interface

Rx Input

Term

Clock Source

If unknown,

select “Internal”

Clock Offset

0 ppm

LBO

0 dB

Framing

If unknown,

select “C

-BIT”

Pattern

Pattern Mode

ANSI

Pattern

2^23

-1 ANSI

Figure 5: Reset Test to Defaults

Figure 8: Setup, Pattern

Figure 7: Setup, Framing

Figure 6: Setup, Interface

VIAVI//Public

OneAdvisor 1000 High-Speed Network Testing Platform

QUICK CARD

RUN TEST

1. Using drop-down menus , select

“Interface/Signal” for the right results display.

2. Press the Restart soft key .

3. Verify the following:

►Summary LED is green.

►Signal Present LED is green.

If the LED is red, check your cables.

Tx and Rx may be reversed.

►Frame Sync LED is green.

►RX Frequency (Hz)

= 44736000 +/- 895 Hz.

4. Using drop-down menus , select

“Payload/BERT” for the right results display.

5. Allow the test to run for desired duration and

verify the following:

►Pattern Sync LED is green.

►Bit/TSE Error Rate result does not

exceed your required threshold.

(0.00E+00 if pass/fail threshold unknown)

Figure 10: Results, Interface/Signal

Figure 9: Mini-BNC Connectors

CONNECT TO LINE UNDER TEST

•The OneAdvisor 100G Transport

Module has mini-BNC ports for

DS3 testing.

•CB-MINITOBNCQTY1 adapters

are required to adapt to a

standard BNC connector.

•You may use BNC to BNC or

BNC to WECO cables to connect

the adapter to the line under test.

Figure 11: Results, Payload BERT

VIAVI//Public

OneAdvisor 1000 High-Speed Network Testing Platform

QUICK CARD

Product specifications and descriptions in this

document are subject to change without notice.

Patented as described at viavisolutions.com/patents

To reach the VIAVI office nearest you,

visit viavisolutions.com/contact

+1 844 GO VIAVI

(+1 844 468-4284)

CREATE REPORT

6. In the OneAdvisor’s Quick Config menu,

change “Pattern” to the next value in the test

plan.

7. Press the Restart soft key to reset results.

8. Allow test to run for desired duration and verify

the following:

►Pattern Sync LED is green.

►Bit/TSE Error Rate does not exceed

your required threshold.

(0.00E+00 if pass/fail threshold unknown)

9. Repeat steps 6 through 8 for all Patterns in the

test plan. Patterns may include:

►Delay: Measures Round Trip Delay (RTD)

instead of Bit Errors (RTD values are shown

instead of BER in the “Payload/BERT”

results display)

►Others

Figure 12: Results, Quick Config

Figure 13: Results, Delay

1. Tap to open the Reports Panel and

select . .

2. Tap .

3. A report will be saved to the OneAdvisor 1000

100G Module’s /bert/reports folder.

Figure 14: Create Report

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi OneExpert DSL ONX-580 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 4000 V2 Bedienungsanleitung

Viavi

Viavi HST-3000 Stücklistenhandbuch

Viavi

Viavi SmartOTDR Stücklistenhandbuch

Viavi

Viavi OneAdvisor-800 Bedienungsanleitung

Viavi

Viavi SmartOTDR Mainframe Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-4000 v2 Stücklistenhandbuch

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi OBS-500 Bedienungsanleitung

Viavi

Viavi SmartOTDR Stücklistenhandbuch

Viavi

Viavi IFR 4000 Stücklistenhandbuch

Viavi

Viavi OneAdvisor 800 Platform Bedienungsanleitung

Viavi

Viavi 4100 Series Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS-2000 Stücklistenhandbuch

Viavi

Viavi T-BERD 5800 Bedienungsanleitung

Viavi

Viavi FCOMP/-PRO T-BERD/MTS-2000V2 Bedienungsanleitung

Viavi

Viavi OneAdvisor ONA-800 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS-5800 Stücklistenhandbuch

Viavi

Viavi E4100 Series Stücklistenhandbuch

Viavi

Viavi MTS 2000 Bedienungsanleitung

Viavi

Viavi HST-3000 Stücklistenhandbuch

Viavi

Viavi OTU-8000 Stücklistenhandbuch

Viavi

Viavi ONX 580 Bedienungsanleitung

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung