Viavi T-BERD MTS 5800 Stücklistenhandbuch

VIAVI//Public

T-BERD/MTS-5800 Handheld Network Tester

T-BERD/MTS-5800 Network Tester

QUICK CARD

► Use the VIAVI P5000i or FiberChek Probe

microscope to inspect both sides of every

connection being used (OCC Port, Launch

Cable, bulkhead connectors, patch cables, etc.)

► Focus fiber on the screen. If dirty, clean the

end-face.

► If it appears clean, run inspection test.

► If it fails, clean the fiber and re-run inspection

test. Repeat until it passes.

Figure 2: Inspect Before You Connect

Figure 1: Equipment Requirements

CWDM Expert OTDR

This quick card explains how to connect to a fiber under test, configure EXPERT OTDR

test settings using Quick Setup, run tests, and analyze results with a VIAVI T-BERD/MTS-

5800 equipped with a 4100-series CWDM OTDR module.

Note: The CWDM OTDR module is used to test individual CWDM channels on a

live network. Care must be taken to select and test the correct channel or

wavelength.

► T-BERD/MTS-5800 equipped with the

following:

•Fiber Optics Software Release V21.0 or

greater

•4100 Series CWDM OTDR Module

(E41CWDMC10L-APC, E41CWDMC10L-PC,

E41CWDM10U-APC, E41CWDM10U-PC,

E41CWDM8U-APC or E41CWDM8U-PC)

► Fiber optic cleaning and inspection tools

►20-meter Fiber optic patch cable (Launch

Cable)

► Optical Coupler to connect Launch Cable to

Fiber Under Test

VIAVI//Public

T-BERD/MTS-5800 Handheld Network Tester

T-BERD/MTS-5800 Network Tester

QUICK CARD

CONNECT TO FIBER UNDER TEST (FUT)

All fibers and connectors should be inspected and clean prior to connection, as described on page 1.

The OTDR may be connected to the FUT via an optical patch panel (OPP) or a coupler:

Figure 4: Connecting to the Fiber Under Test

1. Inspect the OTDR port on top of the test set.

2. Inspect the fiber end face of the Launch Cable.

3. Connect the Launch Cable to the OTDR port.

4. If the interface to the FUT is a patch cord,

connect the patch cord to an optical coupler.

5. Inspect the fiber end face of the Launch Cable.

6. Connect the Launch Cable to the coupler or

OPP.

7. Disconnect or disable the far end SFP on this

channel/wavelength.

LAUNCH TEST

1. Press the Power button to start the test

instrument.

2. Tap the Fiber Optics icon

in the Status Bar at the top of the screen.

3. If a purple symbol is displayed on the left

screen side, tap it to display the Fiber Optics

home screen.

4. Tap the OTDR SM icon until it is yellow and

highlighted .

Figure 5: Fiber Optics Home Screen

Figure 3: Inspecting the OTDR Port

VIAVI//Public

T-BERD/MTS-5800 Handheld Network Tester

T-BERD/MTS-5800 Network Tester

QUICK CARD

CONFI G U RE T E ST

Figure 6: Setup, Display

1. Tap the Setup soft key .

2. Tap Display and set Distance Unit to your

desired unit of measure.

3. Tap Acquisition and configure the following

basic settings for the trace:

►Laser: Select the wavelength to test.

►Acquisition Mode:

–Select Manual to manually to enter

Range and Pulse width settings.

–Select Auto to automatically configure

Range, Pulse width, and Resolution

settings.

–Select SmartAcq to perform an

acquisition with a short pulse width,

followed by an acquisition with a longer

pulse width. The first acquisition allows

events at the beginning of the fiber to be

detected more precisely.

►Acq. Time: Select Realtime, Auto or the

desired time to sample the fiber.

►Launch Cable: Select and enter Length

if you are using a Launch Cable.

Enter 20 meters or 66 feet for Viavi

supplied 20-meter launch cables.

4. Tap Alarms and configure pass/fail criteria:

►Set Alarm Level to Fail.

►Set Threshold to Default, or select

alternate alarm thresholds (TIA-568.3,

User, etc.)

Figure 7: Setup, Acquisition

Figure 8: Setup, Alarms

VIAVI//Public

T-BERD/MTS-5800 Handheld Network Tester

T-BERD/MTS-5800 Network Tester

QUICK CARD

Figure 10: SmartLink View, Summary Results

RUN TES T

1. Press the Start soft key to start the test.

After auto-configuration, the OTDR will perform

a connection check to ensure that the

connection is Good. If the Connection is Bad,

disconnect the launch cable, and reconnect as

described on pages 1 and 2, cleaning every fiber

that fails the inspection test.

2. The OTDR will perform an acquisition at the

configured wavelength.

Figure 11: SmartLink View, Event Results

Figure 9: Connection Check

1. Tap the SmartLink tab at the left screen top to

select SmartLink view.

2. Set the toggle switch at the right screen top to

Event Line.

3. View SmartLink results:

►The FUT is displayed as a series of icons

representing events (Mux, Demux, splices,

bends, connectors, etc.) and distances.

Swipe left or right to view additional icons

on spans with more than 4 events.

►The center of the display shows summary

results for the entire span for each

acquisition or wavelength. Tap any event

in the upper display to view detailed results

for that specific event.

►Events are marked with a green check or

red xbased on the Alarms setting.

Note: the icon-based view may not be

available on older T-BERD/MTS 5800s when

acquisition Mode = SmartAcq. Rerun the test

with the Mode = Auto or contact VIAVI to

upgrade your unit to add this feature.

VI E W S MARTLI N K MAP

VIAVI//Public

T-BERD/MTS-5800 Handheld Network Tester

T-BERD/MTS-5800 Network Tester

QUICK CARD

VI E W T R A CE

1. Tap the Trace tab at the left screen top to select

Trace view.

2. Set the toggle switch at the screen top to Info.

3. Tap to auto-zoom.

4. View trace results:

►Trace information is shown in the upper

display.

►Graphical results (dB versus distance) are

shown in the center display.

►A color-coded Event table is shown in the

lower display. Swipe up and down to view

all events. Figure 12: Trace view

Figure 13: Table view

1. Tap the Table tab at the left screen top to

select Table view.

2. Set the toggle switch at the right screen top to

the center (off) position.

3. View table results:

►Distance, Loss, and Reflectance are

shown for each event.

►Tap the toggle switch to view All events

or Failed events.

VI E W T A BLE

VIAVI//Public

T-BERD/MTS-5800 Handheld Network Tester

T-BERD/MTS-5800 Network Tester

QUICK CARD

Product specifications and descriptions in this

document are subject to change without notice.

Patented as described at viavisolutions.com/patents

To reach the VIAVI office nearest you,

visit viavisolutions.com/contact

+1 844 GO VIAVI

(+1 844 468-4284)

FAST REP O RT

1. Tap the File soft key and tap the fiber

folder.

2. Tap the Create Directory soft key and

enter a name for your new folder. All trace files

will be saved to this directory.

3. Tap the Exit soft key .

4. Tap the Fast Report soft key and enter

Cable ID, Fiber Number, Locations,

Direction, and Save Mode.

5. Tap Save.

6. Tap to accept the default filename and

save test results.

7. Tap the Fast Report soft key again to return to

the results display.

8. Tap to return to the OTDR Home screen.

Figure 14: File Explorer

Figure 15: Fast Report

Andere Handbücher für T-BERD MTS 5800

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi T-BERD/MTS-5800 OCC-4056C Stücklistenhandbuch

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi OSA-4100 Bedienungsanleitung

Viavi

Viavi MTS 2000 Bedienungsanleitung

Viavi

Viavi Parent Guide Bedienungsanleitung

Viavi

Viavi OCC-4056 Stücklistenhandbuch

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 8000 Stücklistenhandbuch

Viavi

Viavi T-BERD MTS 5800 Bedienungsanleitung

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi 3900 Series Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Bedienungsanleitung

Viavi

Viavi OneAdvisor ONA-800 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS-2000 Stücklistenhandbuch

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi 3900 Series Bedienungsanleitung

Viavi

Viavi T-BERD/MTS 5800 Bedienungsanleitung

Viavi

Viavi PSD90-3 Bedienungsanleitung

Viavi

Viavi HST-3000 Bedienungsanleitung

Viavi

Viavi IFR 6000 Stücklistenhandbuch

Viavi

Viavi CT-X Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-4000 v2 Stücklistenhandbuch

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung