Viavi T-BERD MTS 5800 Stücklistenhandbuch

VIAVI Solutions

Quick Card

T-BERD®/MTS-5800 Network Tester

Ethernet Layer 3 Multicast Traffic Analysis

This document outlines how to use the T-BERD 5800 to join Layer 3 Multicast groups and receive and

analyze multicast traffic. Multicast traffic generation is covered in a separate Quick Card.

Equipment Requirements:

•T-BERD/MTS-5800 equipped with the

following:

oBERT software release V27.2 or

greater

oC510M1GE Gigabit Ethernet test

option

oSFP, QSFP, or CFP4 optical

transceiver to match the line under

test

•Patch Cables to match the T-BERD/MTS

optics and the line under test

•Fiber optic inspection microscope

(VIAVI P5000i or FiberChek Probe)

•Fiber Optic Cleaning supplies

Figure 1: Equipment Requirements

The following information is required to complete the test:

•Physical Interface (10/100/1000BASE-T, 1000BASE-LX, 10GBASE-LR, 100GBASE-LR4, etc.)

•Auto Negotiation settings of the port under test

•VLAN ID, if VLAN tagging is used

•IP Address Parameters (DHCP or Static, Source IP, Default Gateway, Subnet Mask)

•IP address for the Multicast Router that handles Multicast Group registration.

•One or more Multicast Group IP Address to receive multicast test traffic.

Fiber Inspection Guidelines:

•All fiber end-faces must be clean and

pass an inspection test prior to

connection.

•Use the VIAVI P5000i, FiberChek Probe,

or Sidewinder microscope to inspect

both sides of every connection being

used (SFP Port, bulkhead connectors,

patch cords, etc.)

Figure 2: Inspect Before You Connect

VIAVI Solutions

Connect to Fiber Under Test (FUT):

1. For copper 10/100/1000BASE-T

interface testing with the T-BERD/MTS

5800v2, connect the Port 1

10/100/1000 RJ-45 jack to the port

under test using CAT 5E or better cable.

2. For copper 10/100/1000BASE-T

interface testing with the T-BERD/MTS

5800-100G, insert a copper SFP into the

Port 1 SFP+/SFP28 slot and connect to

the port under test using CAT 5E or

better cable.

Figure 3: T-BERD 5800v2 Dual Port mainframe

3. For optical interfaces:

•Insert SFP compatible with your

physical interface into the Port 1

slot on the top of T-BERD.

•Inspect and, if necessary, clean all

fibers and bulkheads, as described

on page 1.

•Connect the SFP to the port under

test using a Single Mode or

Multimode jumper cable compatible

with the interface under test.

Figure 4: T-BERD 5800-100G mainframe

Launch and Configure Test:

1. Press the Power button to turn on the test set and view the startup screen.

2. Using the Select Test menu, Quick Launch menu, or Job Manager, launch an Ethernet, Layer 3

Traffic, IPv4, Terminate test on port 1 for the desire physical interface. For example:

Ethernet►10/100/1000►Layer 3 Traffic►IPv4►P1 Terminate.

3. If the test is not in the default settings, tap the Tools icon and select .

Tap and wait for test to reconfigure.

4. Tap the Setup Soft Key to display the Interface settings tab.

5. If you are testing a 10/100/1000 Electrical or 1GigE Optical tests with auto negotiation disabled,

select the Physical Layer tab and configure settings to match the Ethernet port under test.

6. If the network under test uses VLAN tagging, select the Ethernet settings tab, set Encapsulation

to VLAN, tap [VLAN] and enter your VLAN ID.

VIAVI Solutions

7. Select the IP settings tab.

8. Select the Source/Destination

Addresses field.

•Enter the Source IP, Default

Gateway and Subnet Mask values.

•Set Destination IP to the Multicast

Router IP address.

•The T-BERD/MTS will resolve the

destination IP address using the

Address Resolution Protocol (ARP).

Once resolved, the button

becomes available and you can use it

to verify connectivity to the

Multicast Router.

9. Select the IGMP settings tab.

10. Set IGMP Mode to Enabled.

11. Tap the Address Book button to

configure the Multicast Group

Membership.

Figure 5: IP Settings

Figure 6: IGMP Settings

12. Under the New Entry, enter the source

IP address of the T-BERD/MTS Source IP

address in the Source IP field and enter

the Multicast Group IP address in the

Dest. IP field. Optionally, enter a name

for the new entry.

13. Tap on the Add Entry button to save

the Multicast Group entry.

14. If more Multicast Groups need to be

joined during the test, repeat Steps 12

and 13 for all additional Multicast

Groups.

15. Tap on Save and Close button to save

the Address Book information.

16. Tap on the Results button in the upper

left screen corner to move to the

Results screen.

Figure 7: Address Book

VIAVI Solutions

(+1 844 468 4284)

To reach the VIAVI office nearest you,

visit viavisolutions.com/contacts.

Product specifications and descriptions in this

document are subject to change without notice.

Join Multicast Groups:

1. If using the optical test port on

T-BERD/MTS press the Laser Off button

at the bottom of the screen to turn on

the laser. The button will turn yellow

and be relabeled Laser On.

2. Check LEDs: A green Signal Present LED

● indicates the T-BERD/MTS is receiving

an optical signal from the port under

test. Green Sync Acquired and Link

Active LEDs indicate that the T-

BERD/MTS has successfully connected

to the port under test and the link is

active.

3. Use one of the two Results boxes in the

middle of the screen to display the

Ethernet/L3 Link Counts results view to

analyze received multicast traffic.

4. Tap on the Join Streams… button in the

Actions tab at the bottom of the screen

to join the Multicast Groups.

5. Select one or more Multicast Group

entries under Address Book and tap the

Add button to add the entry to the To

Join list.

6. Tap the Join Steams button to join the

selected stream(s).

Figure 8: Results

Figure 9: Join Steams...

Analyze Multicast Traffic:

1. Once one or more Multicast Groups are

successfully joined, the T-BERD/MTS

will start receiving multicast test traffic

as indicated by the Multicast Packets

counter on the Ethernet -> L3 Link

Counts results view.

2. You can now use other available results

views to analyze the multicast traffic

performance.

Figure 10: Results view

Andere Handbücher für T-BERD MTS 5800

Inhaltsverzeichnis

Andere Viavi Prüfgeräte Handbücher

Viavi

Viavi ONX 580 Bedienungsanleitung

Viavi

Viavi T-BERD 5800 Bedienungsanleitung

Viavi

Viavi SmartOTDR Stücklistenhandbuch

Viavi

Viavi OneAdvisor 800 Series Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-5800 Stücklistenhandbuch

Viavi

Viavi OneAdvisor ONA-800 Technisches Handbuch

Viavi

Viavi T-BERD/MTS-4000 v2 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS-580 Installationsanleitung

Viavi

Viavi HST-3000 Bedienungsanleitung

Viavi

Viavi AVX-10K Bedienungsanleitung

Viavi

Viavi T-BERD/MTS-4000 v2 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS 5800 Bedienungsanleitung

Viavi

Viavi 8000 V2 Platform Bedienungsanleitung

Viavi

Viavi OneAdvisor ONA-800 Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS 5800 Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Bedienungsanleitung

Viavi

Viavi 3900 Series Bedienungsanleitung

Viavi

Viavi SmartClass Fiber MPOLx Stücklistenhandbuch

Viavi

Viavi T-BERD/MTS 5800 Installationsanleitung

Viavi

Viavi OneAdvisor 1000 Bedienungsanleitung

Viavi

Viavi COSA-4055 Stücklistenhandbuch

Viavi

Viavi ATC-5000NG Bedienungsanleitung

Viavi

Viavi T-BERD MTS 5800 Stücklistenhandbuch

Viavi

Viavi T-BERD 5800 Stücklistenhandbuch

Beliebte Prüfgeräte Handbücher anderer Marken

SMART

SMART KANAAD SBT XTREME 3G Series Bedienungsanleitung

Agilent Technologies

Agilent Technologies BERT Serial Bedienungsanleitung

Agilent Technologies

Agilent Technologies N3280A Bedienungsanleitung

Lifeloc

Lifeloc R.A.D.A.R. Bedienungsanleitung

Fluke

Fluke T5-600 Bedienungs- und Montageanleitung

Mercury

Mercury TSL01 Bedienungsanleitung

MAHA

MAHA MBT Series Bedienungsanleitung

Fuji Electric

Fuji Electric P-61 Bedienungsanleitung

ETC

ETC SealerAtor Bedienungsanleitung

Skyfine

Skyfine ETHYWAY V2 Bedienungsanleitung

Appion

Appion G5 Twin Bedienungsanleitung

PCB Piezotronics

PCB Piezotronics 8159-0112A Bedienungsanleitung

BW Technologies

BW Technologies MicroDock II Bedienungsanleitung

Sun Nuclear

Sun Nuclear 1027 Bedienungsanleitung

Biomark

Biomark HPR LITE READER Bedienungsanleitung

Hioki

Hioki 3169-20 Bedienungsanleitung

Ashcroft

Ashcroft ATE-100 Bedienungsanleitung

Rohde & Schwarz

Rohde & Schwarz RTA4000 Bedienungsanleitung