Vicon XX214-20-03 Bedienungsanleitung

www.vicon-security.com

XX214-20-03

Surveyor® HD Series Network

Camera Domes

Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the

operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed

to be used in life-critical situations and must not be used for this purpose.

Vicon Industries Inc.

Tel: 631-952-2288 Fax: 631-951-2288 Toll Free: 800-645-9116

24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: 44/(0) 1489-566300

Document Number: 8009-8214-20-03

Product specications subject to change without notice.

Issued: 1013

Quick Guide

Quick Operation Guide | 1

Surveyor HD Camera Dome

Quick Operation Guide

This manual provides a quick overview for the operation of the Surveyor®

HD Series of Camera Domes. Refer to the complete manual, XX214-0X

(installation) and XX214-4X (web browser), for complete details on

installation, setup and operating details.

The Surveyor HD is a compact network dome comprised of a

camera/lens and pan/tilt drive in an attractive covert enclosure. Surveyor

HD is sold in a variety of prepackaged configurations with choices in

environment, mounting configuration, and lower dome types.

The Surveyor HD supports high-profile H.264 or M-JPEG compression.

The dome supports ONVIF open architecture connectivity to enable

integration into third party software recording solutions, as well as Vicon’s

ViconNet.

The Surveyor HD is designed for easy installation and serviceability. The

entire drive assembly simply snaps into the housing. When removed, the

mechanism retains all programmed functions in its on-board memory.

The customer interface board snaps down for easy access and the PCB

provides removable terminal blocks for simple wiring connections. Power

to the indoor units can be provided by PoE+ (Power over Ethernet Plus);

outdoor units require 24 VAC. The Surveyor HD includes a high-definition

1.3 or 2.0 megapixel day/night camera with wide dynamic range (WDR)

and digital noise reduction (DNR/FNR).

2| Quick Operation Guide

Installation

In-Ceiling

Quick Operation Guide | 3

Pendant

4| Quick Operation Guide

Pressurized

Quick Operation Guide | 5

Wiring and Setup

CONNECTOR/PIN

NUMBER

CONNECTOR TYPE CONNECTOR/PIN LABEL SIGNAL NAME

TERMINAL BLOCK POWER (TB2)

TB2-1 AC+ Hot

TB2-2 AC- Neutral

TERMINAL BLOCK ALARM (TB1)

TB1-1 ALARM 1 Alarm I/O 1

TB1-2 Ground

TB1-3 ALARM 2 Alarm I/O 2

TB1-4 Ground

TB1-5 ALARM 3 Alarm I/O 3

TB1-6 Ground

TB1-7 ALARM 4 Alarm I/O 4

TB1-8 Ground

TERMINAL BLOCK COMM/RELAY (TB5)

TB5-1 VSS Ground

TB5-2 CRelay, common

TB5-3 NO Relay, normally open

TB5-4 NC Relay, normally closed

RJ-45 LAN (J6)

J6-1 Transmit +

J6-2 Transmit -

J6-3 Receive +

J6-4 PoE spare

J6-5 PoE spare

J6-6 Receive -

J6-7 PoE spare

J6-8 PoE spare

1/8-IN. PHONO AUDIO (J9)

J9 J9 Audio In

6| Quick Operation Guide

Setting the DIP Switches

There are two DIP switches that must be set on the Surveyor HD. One is

on the Communications Interface (CI) board and one on the Main board.

SW1 4-position DIP switch is on the Communication Interface (CI) board.

For SW1 all poles should be set to OFF (default).

DIP Switch Location on CI Board

Caution

Changing the positions on the DIP switch on the Main board should only

be done by a qualified person. Position 1 is used only if it is necessary to

force the unit into default setup if network or system connections are lost.

Be sure to reset this switch back to the OFF position before the next

power up to avoid a constant return to defaults, resulting in not being able

to enter the camera’s IP to use the Web Browser. The camera dome is

shipped with a default static IP of 1.1.1.2.

The Main board has an 8-position DIP switch SW1. The settings for the

positions of this DIP Switch are:

Position 1 - Set Network Address. OFF = Default Position, do not

set network defaults. ON = Set k default network address (1.1.1.2);

must be reset OFF after reboot and before next power up.

Position 2 – Unused (set to OFF)

Position 3 – For factory use only. OFF is Default.

Position 4 – Unused (set to OFF)

Quick Operation Guide | 7

Position 5 – Unused (set to OFF)

Position 6 - Unused (set to OFF)

Position 7 – Set password. OFF = Default Position. ON = Reset to

default password (password); must be reset to OFF after reboot

and before next power up.

Position 8 – System Mode. OFF = Default Position, ViconNet

Mode. ON = ONVIF/NTCIP Mode.

The main board is located underneath the housing. It may be necessary

to spin the housing mechanism to see the DIP switch, located near the tilt

motor along edge of the board.

DIP Switch Location on Main Board

Communication Ports

If using NTCIP protocol, communicate to the Surveyor HD using ports

3000/UDP or 3001/TCP.

If using ONVIF, use port 8000.

8| Quick Operation Guide

Pressurized Cable Preparation

Using the prefabricated cable

Using a customer prepared cable

Quick Operation Guide | 9

Using the Web Browser Interface

Web Browser Interface

The Web Browser Interface provides a user friendly interface to configure

and control various features and functions of the Surveyor™ HD camera

dome. The interface allows the configuration of camera dome

parameters, viewing live video, using PTZ, setting administrative controls

and collecting camera dome reports and status information.

There are six (6) functional areas (pages) on the Web Browser Interface,

Camera Login, Live Video, Add/Edit Users, Settings, Maintenance and

System Information.

VMS Compatibility

The Surveyor HD Camera Dome is an ONVIF compliant open platform

product designed to be used with multiple Video Management Systems

(VMS). For initial setup when using the ViconNet VMS, refer to Appendix

A in XX214-4X for information on using the “VNSetup” discovery and

configuration application.

VMS specific tools may be necessary to use the dome with each system,

such as a Discovery Tool. Refer to their documentation.

Access the Camera

Open a browser (i.e., Internet Explorer). Enter the IP address or host

name of the camera in the Location/Address field of your browser. The

camera dome is shipped with a default IP static of 1.1.1.2; change your

PC’s IP to match the Subnet if needed.

You may be asked to load ActiveX software; click to download it at this

time.

The Surveyor HD login screen displays.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Vicon Kamerazubehör Handbücher

Vicon

Vicon Roughneck V920D Series Bedienungsanleitung

Vicon

Vicon SURVEYOR4 Series Bedienungsanleitung

Vicon

Vicon SUR4-PH Bedienungsanleitung

Vicon

Vicon ViStar VIST35 Series Bedienungsanleitung

Vicon

Vicon CE102D Bedienungsanleitung

Vicon

Vicon SurveyorVFT Betriebsanleitung

Vicon

Vicon V926-PHS Bedienungsanleitung

Vicon

Vicon roughneck V900 Montage- und Bedienungsanleitung

Vicon

Vicon HOV Bedienungsanleitung

Vicon

Vicon SUR4-PH Bedienungsanleitung

Vicon

Vicon V9312H Series Bedienungsanleitung

Vicon

Vicon V4-H-P Bedienungsanleitung

Vicon

Vicon V910-PH Bedienungsanleitung

Vicon

Vicon V402 Series Benutzerhandbuch

Vicon

Vicon V926-PHS Bedienungsanleitung

Vicon

Vicon ALU-2500/230 Bedienungsanleitung

Vicon

Vicon V9315H Series Bedienungsanleitung

Vicon

Vicon SVFT-PRS Bedienungsanleitung

Vicon

Vicon V896MSH Benutzerhandbuch

Vicon

Vicon V660-TRIM Bedienungsanleitung

Vicon

Vicon V235GLTA-1 Bedienungsanleitung

Vicon

Vicon V8606H-XD Benutzerhandbuch

Vicon

Vicon XX214-60-06 Bedienungsanleitung

Vicon

Vicon ACTIVE WAND Bedienungsanleitung

Beliebte Kamerazubehör Handbücher anderer Marken

Viltrox

Viltrox EF-NEX Montageanleitung

Calumet

Calumet 7100 Series CK7114 Bedienungsanleitung

Ropox

Ropox 4Single Series Bedienungsanleitung

Cambo

Cambo Wide DS Digital Series Betriebsanleitung

Samsung

Samsung SHG-120 Bedienungsanleitung

Ryobi

Ryobi BPL-1820 Bedienungsanleitung

Aegis

Aegis ABL-36020P Bedienungsanleitung

Pentax

Pentax Data Back Fc Bedienungsanleitung

Fantasea

Fantasea EyeGrabber F Series Bedienungsanleitung

Honeywell

Honeywell HDZ20HD Bedienungsanleitung

EGO

EGO BA1400T Bedienungsanleitung

Sima

Sima SRW-62 Bedienungsanleitung

Shape

Shape A7SSMKIT Bedienungsanleitung

Slide Kamera

Slide Kamera HST-2 Bedienungsanleitung

Power works

Power works 2902613 Bedienungsanleitung

SES

SES SE-2047-2 Bedienungsanleitung

Olympus

Olympus PT-EP05L Bedienungsanleitung

Starlite

Starlite OctoDome nxt Bedienungsanleitung