Vicon V2000B-BOX Bedienungsanleitung

Waterproof Rubber Sealing

Holding Bracket Plate

Wall & Surface Mount with Junction Box Kit

V2000B-BOX

For V2000B Bullet & V2360W Panoramic

Cameras

Quick Guide

1. Product Overview

FIGURE 1-1: PHYSICAL DIMENSION

Screw & Waterproof Rubber Sealing Instruction

Since the junction box supports multiple devices, it is recommended

to review the following diagram carefully, which depicts different

screw types and waterproof rubber bushing for each device, prior to

installation.

FIGURE 1-2: SCREW TYPES ILLUSTRATION

FIGURE 1-3: WATERPROOF RUBBER BUSHING ILLUSTRATION

2. Installation and Mounting

Package Content

Check if all items listed below are included in the packing box.

⚫One adaptor plate

⚫Two waterproof bushings

⚫One holding bracket plate

⚫One junction box

⚫One torx wrench

⚫One mounting template

⚫One printed quick guide

⚫Six TP4 tapping screws

⚫Six screw anchors

⚫Three M2.6X5mm screws

⚫Four M4X5mm screws (for V2360W Panoramic)

⚫Six M4X14mm screws (for V2000B Bullet)

Required Tools

The following tools might help during the installation:

⚫A drill

⚫A hammer

⚫A Phillips head screwdriver

⚫Wire cutters

Installation & Mounting Procedure

1. Drill 6 holes on wall or surface based on the mounting

template. Diameter φ3/8” (9.5mm), depth 1/1/2” (40mm).

2. Hammer the 6 screw anchors into the drilled holes.

3. Fix the junction box onto the wall/surface by fastening the 6 TP4

tapping screws with the 6 screw anchors.

FIGURE 2-1: FIX JUNCTION BOX

3. Mounting Procedure

For IR Bullet Camera

1. Pass the camera cable through the adaptor plate, and then

secure the camera to the adaptor plate by fastening the 6

M4X14mm screws.

FIGURE 3-1: SECURE CAMERA WITH ADAPTOR PLATE

2. From the rear, cover the cable with the waterproof rubber

bushing and fasten them to the holding bracket plate using 3

M2.6X5mm screws onto the proper hole.

FIGURE 3-2: CABLE THREAD PREPARATION

3. Place thecable inside the junction box to connect with required

cables coming from either the bottom or side conduit hole of

the camera, depending on type of application, and attach the

junction box with the adaptor plate by fastening the

3 T20 screws with T20 torx wrench.

FIGURE 3-3: ASSEMBLE \JUNCTION BOX WITH ADAPTOR PLATE

4. Finally, install the mounting kit with camera onto a wall or

surface.

FIGURE 3-4: MOUNTING COMPLETE

Be sure that unused ¾ NPT hole

is sealed with the supplied cap.

Ø5.8 (147)

M4X5mm screw

M4X14mm screw

For V2360W

panoramic camera

(Recommended

cable diameter no

less than 5mm)

For V2000B bullet camera

Unit: in. (mm)

Ø5.8 (147)

2.4 (60)

Waterproof Rubber Bushing

For Panoramic Camera

1. Pass the camera cable through the adaptor plate and then

secure the cable with waterproof rubber bushing.

2. Fasten the waterproof rubber bushing to the holding bracket

plate with the 3 M2.6X5mm screws.

FIGURE 3-5: SECURE ADAPTOR PLATE ON JUNCTION BOX

3. Secure the adaptor plate on junction box by fastening with the

3 T20 screws T20 torx wrench.

FIGURE 3-6: SECURE ADAPTOR PLATE ON JUNCTION BOX

4. Secure the bracket on adapter plate by fastening the 4

M4X5mm screws, and then push the cable into junction box.

FIGURE 3-7: SECURE THE BRACKET ON ADAPTOR PLATE

Rotate panoramic camera to secure the screw on the bracket.

Then, rotate the T10 screw on panoramic camera

counterclockwise to make sure panoramic camera does not

rotate.

FIGURE 2-8: SECURE CAMERA ON BRACKET

Notes & Warnings

The holes for wall/surface mount are of diameter φ 10 mm. Use

screws of φ 8~9mm, and make sure the drilled holes are of

correct size to ensure proper installation.

When drilling the hole, make sure the wall/surface thickness is

greater than 50mm in order to maintain its structural integrity.

Make sure there are no damaged parts prior to assembly.

4. Specification

Material

Aluminum

Color

White

Dimensions (WxHxD)

5.8x5.8x2.4 in. (147x147x60 mm)

Weight

2.3 lb (0.85 kg)

Product specifications subject to change without notice.

Vicon part number: 8009-8318-90-00 10/2020

Holding Bracket Plate

Waterproof Rubber Sealing

Waterproof Rubber Bushing

Andere Vicon Rack & Stand Handbücher

Beliebte Rack & Stand Handbücher anderer Marken

Salamander

Salamander Acadia AC/W/L400/WH Bedienungsanleitung

Fohhn

Fohhn VAT-09 Benutzerhandbuch

ricoo

ricoo FS0522 Bedienungsanleitung

AMSOIL

AMSOIL BMK-22 Kurzanleitung

Kargo Master

Kargo Master 48220 Bedienungsanleitung

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Bedienungsanleitung

ricoo

ricoo S1222 Bedienungsanleitung

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Bedienungsanleitung

VidaBox

VidaBox VB MNT FFS2 Bedienungsanleitung

Welch Allyn

Welch Allyn 48960 Bedienungsanleitung

Arkon

Arkon CM035-ST-2 Bedienungsanleitung

PROEL

PROEL PLWIN60C Bedienungsanleitung

Agilent Technologies

Agilent Technologies E2609B Bedienungsanleitung

Mustang

Mustang MV-ARM4 Bedienungsanleitung

Mounting Solutions

Mounting Solutions WRM-320 Bedienungsanleitung

Pyle

Pyle PMKSPAD1 Bedienungsanleitung

ShelterIt

ShelterIt 21208 Bedienungsanleitung

SPL

SPL RackPack?4 1040 Bedienungsanleitung