Viconics VTR7300 Series Bedienungsanleitung

1 | PIR Ready VTR7300 Series-Installation Guide

CONTENTS

Installation 2

Location 2

Installation 2

Operation Overview 3

Model Chart 5

Network ready 6

Terminal, Identification and Function 6

Communication wiring to VC3xxxX Relay Pack 6

Network wiring topology 7

VC3xxx LED Operation 7

Wiring of local inputs to VTR73xxA Terminal Equipment Controller 8

Configuring and Status Display Instructions 8

Status display 8

User Interface 10

Local keypad interface 10

Dual occupied setpoints adjustment 11

Single occupied setpoints adjustment 11

Unoccupied and stand-by setpoints adjustments 11

Mode button menu sequence. 11

Installer Configuration Parameter Menu 12

Configuration interface 13

PIR Ready VTR7300 Series

Terminal Equipment Controller

Installation Guide

For Commercial and Lodging HVAC

Fan Coil Applications

May 3rd, 2012 / 028-0298-R8

2 | PIR Ready VTR7300 Series-Installation Guide

INSTALLATION

Remove the security screw on the bottom of

Terminal Equipment Controller cover.

Open unit by pulling on the bottom

side of Terminal Equipment Controller

(fig. 1).

Remove wiring terminals from sticker.

Please read the FCC ID and IC label

installed in the cover upon removal of

cover for the wireless products.

Location

1. Should not be installed on an outside

wall.

2. Must be installed away from any

direct heat source.

3. Should not be installed near an air

discharge grill.

4. Should not be affected by direct sun

radiation.

5. Nothing should restrict vertical air

circulation to the Terminal Equipment

Controller.

Installation

1. Swing open the Terminal Equipment

Controller PCB to the left by pressing

the PCB locking tabs (fig. 2).

2. Pull out cables 6” out from the wall.

3. Wall surface must be flat and clean.

4. Insert cable in the central hole of the

base.

5. Align the base and mark the location

of the two mounting holes on the wall.

Install proper side of base up.

6. Install anchors in the wall.

7. Insert screws in mounting holes on

each side of the base (fig. 2).

8. Gently swing back the circuit board on

the base and push on it until the tabs

lock it.

9. Strip each wire 1/4 inch from end.

10. Insert each wire according to wiring

diagram.

11. Gently push excess wiring back into

hole (fig. 3).

3 | PIR Ready VTR7300 Series-Installation Guide

12. Re-Install wiring terminals in their correct locations (fig. 3).

13. Re-install the cover (top side first) and gently push extra wire length back into the

hole in the wall.

14. Install security screw.

OPERATION OVERVIEW

The VC3xxxX Series Line Voltage Switching Transformer Relay Pack(s) operate as slave

unit(s) under the control of a single master VTR73xxA Terminal Equipment Controller.

Fan operation can be configured and wired for the following:

3 Speed configuration using 3 fan relays ( Low - Med - High )

2 Speed configuration using 2 fan relays ( Low - High )

3 Speed configuration with auto fan speed mode using 3 fan relays

( Low - Med - High - Auto )

2 Speed configuration with auto fan speed mode using 2 fan relays

( Low - High - Auto )

Single fan speed configuration.

The VTR7300 Controller can be configured for typical 2 or 4 pipe heating / cooling FCU

(Fan Coil Unit) applications.

2 or 4 pipe only operation can be configured and wired for the following:

oCooling only

oHeating only

oCooling / Heating with network or local auto changeover

If replacing an existing Line Voltage FCU Thermostat, label the wires

before removal of the thermostat.

Electronic controls are static sensitive devices. Discharge yourself

properly before manipulating and installing the Terminal Equipment

Controller.

A short circuit or wrong wiring may permanently damage the Terminal

Equipment Controller or the equipment.

All VTR7300 series controls are designed for use as operating controls

only and are not safety devices. These instruments have undergone

rigorous tests and verification prior to shipping to ensure proper and

reliable operation in the field. Whenever a control failure could lead to

personal injury and/or loss of property, it becomes the responsibility of

the user / installer / electrical system designer to incorporate safety

devices ( such as relays, flow switch, thermal protections, etc…) and/or

an alarm system to protect the entire system against such catastrophic

failures. Tampering with the devices or unintended application of the

devices will result in a void of warranty.

4 | PIR Ready VTR7300 Series-Installation Guide

2 or 4 pipe only with electric reheat can be configured and wired for the following:

oCooling only

oHeating only

oCooling / Heating with network or local auto changeover

oOn-Off electric reheat only

oCooling with On-Off or modulating VDC pulsed electric reheat

( model dependent )

oHeating with On-Off or modulating VDC pulsed electric reheat

( model dependent )

oCooling / Heating with network or local changeover with On-Off

or modulating VDC pulsed electric reheat ( model dependent )

The VC3xxxX Relay Pack supplies power to the wall VTR73xxA Terminal

Equipment Controller.

The VTR73xxA Controller controls the VC3xxxX Relay Pack(s) via a simple

communication bus.

A maximum of 10 VC3xxxX Relay Pack can be used under a single VTR73xxA

Terminal Equipment Controller.

3 wires minimum are required between the VTR73xxA Controller and the first

VR7300 Relay Pack.

The 3 wire functions are known as the following:

o1 Tx / Rx Communication

o2 Power Hot 7.0 VDC 4 Watts maximum ( required for the

VTR73xxA Controller power )

o3 Power common

Commands for fan speed and valve operation are issued from the VTR73xxA

Terminal Equipment Controller to the VC3xxxX Relay Pack(s)

5 | PIR Ready VTR7300 Series-Installation Guide

MODEL CHART

6 | PIR Ready VTR7300 Series-Installation Guide

Network ready

All Viconics VTR7300 series Terminal Equipment Controllers are designed for

stand-alone operation.

They can be fully integrated into your choice of automation systems using the

available communication adapter options.

If required, stand-alone (Network Ready) Terminal Equipment Controllers can be

field retrofitted with the following communication adapters:

oVCM7000V5000W, Terminal Equipment Controller wireless

communication adapter

oVCM7300T5000B, Terminal Equipment Controller BACnet™ MS-TP

communication adapter

TERMINAL,IDENTIFICATION AND FUNCTION

TERMINAL

IDENTIFICATION

ALL VTR73XXA5X00(X)

TERMINAL EQUIPMENT CONTROLLER

Terminal 3

Tx –Rx Communication

Terminal 4

Power Hot 7.0 VDC

Terminal 5

Power Common

Terminal 13

BI 1 ( Configurable )

Terminal 14

Scom

Terminal 15

BI 2 ( Configurable )

COMMUNICATION WIRING TO VC3XXXXRELAY PACK

Only ONE VC3xxxX Relay Pack with remote monitoring inputs can be used under a single

VTR73xxA Controller. All other slave units must be VC3xxxX Relay Pack(s) WITHOUT

remote inputs. A maximum of 10 VC3xxxX Relay Packs can be used for a single

VTR73xxA Terminal Equipment Controller.

7 | PIR Ready VTR7300 Series-Installation Guide

From the VTR73xxA to the first VC3xxxX Relay Pack

Uses existing or new field wires

A minimum of 3 wires are required 14-22 Ga Solid or Stranded. Shield not

necessary.

From the first VC3xxxX to all other slave VC3xxxX Relay Pack(s)

Uses existing or new field wires

A minimum of 2 wires are required 14-22 Ga Solid or Stranded. Shield not

necessary.

Connect only wires #1 Power Common and #2 Tx/Rx Communication

Network wiring topology

VC3XXX LED OPERATION

LED / Time (Status operation)

Condition of the Status LED

Cause

Solution

2 short blinks

No communication between

the VTR73xxA and the

VC3xxxX relay pack. The

VC3xxxX Relay Pack will

resume its output “no

communication active” status

Check communication

wiring and or power

cycle the controllers

2 short blinks and a

longer blink

Normal communication

between the VTR73xxA and

the VC3xxxX relay pack.

N/A

0.2

2.5

0.6

0.4

0.0

1.0

5.0 sec

Power On

Online to

VTR73xxA

8 | PIR Ready VTR7300 Series-Installation Guide

Wiring of local inputs to VTR73xxA Terminal Equipment Controller

CONFIGURING AND STATUS DISPLAY INSTRUCTIONS

Status display

The VTR73xxA Terminal Equipment Controller features a two-line, eight-character display.

There is a low-level backlight that is always active and can only be seen at night.

When left unattended, the Terminal Equipment Controller has an auto scrolling display

that shows the status of the system. There is an option in the configuration menu to

lockout the scrolling display and to only display the room temperature and conditional

outdoor temperature to the user. With this option enabled, no local status of mode,

occupancy and relative humidity is shown.

Each item scrolls individually with the back lighting in low level mode. Pressing any key

will cause the back light to come on to high level. When left unattended for 10 seconds

after changes are made, the display will resume automatic status display scrolling.

To activate the back light to high level, press any key on the front panel. The back light

display will return to low level when the Terminal Equipment Controller is left unattended

for 45 seconds.

Sequence of auto-scroll status display:

ROOM &

HUMIDITY

SYSTEM MODE

SCHEDULE

STATUS

OUTDOOR

TEMPERATURE

ALARMS

x.x °C or °F

XX % RH

Sys mode

auto

Occupied

Outdoor

x.x °C or °F

Service

If humidity display

enabled

Sys mode

cool

Stand-By

Network value only

Filter

RoomTemp

x.x °C or °F

Sys mode

heat

Unoccup

n/a

Window

If humidity display

is not enabled

Sys mode

off

Override

n/a

Low Batt

VTR73xxA

Terminal Controller

BI 1

Scom

BI 2

Local BI 1 Input by configuration:

None (monitoring only)

Remote motion detector: Motion NO or Motion NC

- Remote Night Setback: RemNSB

Local BI 2 Input by configuration:

None (monitoring only)

Door contact: DoorDry

- Window contact Window:

9 | PIR Ready VTR7300 Series-Installation Guide

% RH display is conditional to:

(Humidity display is model and configuration dependent)

Model with RH sensor built in

Display function can be enabled with RH display parameter. Displayed range is

10 to 90 % RH

Outdoor air temperature

Display is only enabled when outdoor air temperature network variable is

received.

Occupancy status

Occupied, Stand-By, Unoccupied and Override status are displayed on the

scrolling display.

Alarms

If alarms are detected, they will automatically be displayed at the end of the

scrolling status display.

When an alarm message is displayed, the backlit screen will illuminate at the

same time as the message and shut off during the rest of the status display.

A maximum of two alarms can appear at any given time. The priority for the

alarms are as follows:

Three status LED’s on the Terminal Equipment Controller cover are used to indicate the

status of the fan (any speed), a call for heat, or a call for cooling.

Fan coil models

When any of the fan speeds are ON, the FAN LED will illuminate

When heating & reheat is ON, the HEAT LED will illuminate

When cooling is ON, the COOL LED will illuminate

Service

Indicates that there is a service alarm as per one of the configurable binary

inputs ( BI2 )

Filter

Indicates that the filters are dirty as per one of the configurable binary

inputs ( BI2 )

Window

Indicates that the outside window or door is opened and that the Terminal

Equipment Controller has cancelled any cooling or heating action ( BI1 )

Low

Batt

Indicates that attached wireless switching devices ( Door or window contact ) have

a low battery condition.

(Only functional when used with a wireless communication adapter)

10 | PIR Ready VTR7300 Series-Installation Guide

USER INTERFACE

Unoccupied mode override

An Override can be made on commercial models during an unoccupied period. If the

Override option is enabled in the lockout configuration, pressing the middle override

button will resume occupied setpoints for a time specified by the parameter “ToccTime”.

Local keypad interface

Any setpoint change can be permanent or temporary based on configuration

parameter (Setpoint Type)

Any setpoint written through the network, will be permanent and cancel any

active temporary setpoints

Lockouts of access to certain functions is made with configuration parameter

(lockout)

Is used to toggle between the different system modes available as per

sequence and menu selected.

Repetitively pressing the button will toggle between all the available modes.

Available menus are dependent on selected sequence of operation.

Is used to toggle between the different fan modes available as per the

sequence and menu selected

Repetitively pressing the button will toggle between all the available modes

Available menus are dependent on selected sequence of operation and menu

selected for Fan

Hotel and lodging applications. Toggles the local user temperature scale

between °F and °C

Commercial and institutional applications. Set a local unoccupied timed

override to occupied mode

In cooling mode only the cooling setpoint is displayed,

In heating mode only the heating setpoint is displayed

In auto mode, (See below)

In cooling mode only the cooling setpoint is displayed,

In heating mode only the heating setpoint is displayed

In auto mode, (See below)

Andere Handbücher für VTR7300 Series

Inhaltsverzeichnis

Andere Viconics Controller Handbücher

Viconics

Viconics VT8000 Series Datenblatt

Viconics

Viconics VT7600E Series Bedienungsanleitung

Viconics

Viconics VT8000 Series Bedienungsanleitung

Viconics

Viconics VT7225 series Bedienungsanleitung

Viconics

Viconics VT7600W Series Bedienungsanleitung

Viconics

Viconics VT8000 Series Bedienungsanleitung

Viconics

Viconics VT8000 Series Bedienungsanleitung

Viconics

Viconics R820 REV2 Series Bedienungsanleitung

Viconics

Viconics VC3000 Series Bedienungsanleitung

Viconics

Viconics VT8000 Series Bedienungsanleitung

Viconics

Viconics VT8000 Series Bedienungsanleitung

Viconics

Viconics VT76 Series Gebrauchs- und Pflegehandbuch

Viconics

Viconics VTR8300 Series Benutzerhandbuch

Viconics

Viconics VT7600 Series Bedienungsanleitung

Viconics

Viconics VT8000 Series Bedienungsanleitung

Viconics

Viconics VZ7260 5 00B Series Benutzerhandbuch

Viconics

Viconics VZ8250 Bedienungsanleitung

Viconics

Viconics VT7200 Series Bedienungsanleitung

Viconics

Viconics VT7225 series Bedienungsanleitung

Viconics

Viconics VTR7300 Series Bedienungsanleitung

Viconics

Viconics ZigBee Pro VT8000 Series Bedienungsanleitung

Viconics

Viconics VT7600F Series Bedienungsanleitung

Viconics

Viconics R851V-4 Bedienungsanleitung

Viconics

Viconics VT8600 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung