Viconics ZigBee Pro VT8000 Series Bedienungsanleitung

ZigBee Pro Module

Installation Guide

VT8000 Series Room Controllers

Optional ZigBee Pro Module (VCM8000V5000P)

ZigBee Module Installation Guide 2

028-0425-01 www.viconics.com | sales@viconics.com November 2014

This guide shows you how to install the ZigBee Pro

wireless module with a VT8000 Series Room Controller.

1. Remove security screw on bottom of Room Controller

cover.

2. Open unit by pulling on bottom of Room Controller

(Figure 1).

3. Carefully remove Room Controllers Motherboard from

casing and turn over.

4. Locate gap in upper-right corner of Room Controllers

Motherboard and locate holes to insert ZigBee Pro

module to Motherboard (Figure 2).

5. Align connector pins on ZigBee Pro module with holes

on Motherboard.

NOTE:ensure alignment of pins is correct so as to not

damage ZigBee Pro module.

6. Gently press ZigBee Pro module into Room Controllers

Motherboard until it ﬁts snugly in place.

NOTE:do not press too hard to avoid damage to ZigBee

Pro module.

7. Gently replace Room Controllers Motherboard into

casing.

8. Gently align cover to top of base and snap in place

from bottom (Figure 3).

9. Install security screw.

Figure-1

Figure-3

Figure-2

ZigBee Module Installation Guide 3

028-0425-01 www.viconics.com | sales@viconics.com November 2014

Quick setup

This short procedure is intended to let you pair a ZigBee sensor with your Room Controller. It assumes that all the back-end conﬁguration

of the stand alone Room Controller acting as coordinator or the Multi-Purpose Manager (MPM) coordinator for the ZigBee network has

already been done, and it assumes that the user is familiar with the Permit Join function and the Wireless Ecosystem screen functions.

PROCEDURE

1. Set Permit Join on your Room Controller (or networked MPM coordinator if used) to On.

2. Go to the ﬁrst unused Zone screen in the Wireless Ecosystem section of the Room Controller’s interface.

3. Insert the battery or remove the pull tab (for contact sensors) to activate the ZigBee sensor

4. Verify that the sensor has joined the network, and that on the Zone screen the Paired ﬁeld status reads Yes.

5. Set the Set function to parameter to the correct setting.

6. Set Permit Join on your Room Controller (or networked MPM coordinator if used) to Off.

7. Conditional to use of door or window contact sensors

a) Go to the ﬁrst screen in the Conﬁguration section of the interface.

b) For window sensor, set UI 16 to Window

c) For door sensor, set UI 17 to Door Dry

8. Physically install the sensor.

TROUBLESHOOTING

If the short procedure described here is insufﬁcient or an MPM or Room Controller needs to be conﬁgured, please refer to the VT8000

Room Controllers ZigBee Pro Wireless Integration Guide available on buildingsdownloads.schneider-electric.com.

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Viconics Controller Handbücher

Viconics

Viconics VT7600F Series Bedienungsanleitung

Viconics

Viconics VT7200 Series Bedienungsanleitung

Viconics

Viconics VT8000 Series Bedienungsanleitung

Viconics

Viconics VT8000 Series Bedienungsanleitung

Viconics

Viconics VT7200 F 5000 B Bedienungsanleitung

Viconics

Viconics COV-PIR-FCU-C-5000 Bedienungsanleitung

Viconics

Viconics VC3000 Series Bedienungsanleitung

Viconics

Viconics VT7225 series Bedienungsanleitung

Viconics

Viconics VZ8250 Bedienungsanleitung

Viconics

Viconics VZ7656F1000W Bedienungsanleitung

Viconics

Viconics VTR7300 Series Bedienungsanleitung

Viconics

Viconics VT7600E Series Bedienungsanleitung

Viconics

Viconics VT8000 Series Bedienungsanleitung

Viconics

Viconics VTR7300 Series Bedienungsanleitung

Viconics

Viconics R851B Bedienungsanleitung

Viconics

Viconics VT7225 series Bedienungsanleitung

Viconics

Viconics R851V-4 Bedienungsanleitung

Viconics

Viconics VZ7656F1000B Bedienungsanleitung

Viconics

Viconics VT8000 Series Bedienungsanleitung

Viconics

Viconics VT8000 Series Bedienungsanleitung

Viconics

Viconics R850 Series Bedienungsanleitung

Viconics

Viconics VTR8300 Series Bedienungsanleitung

Viconics

Viconics VTR8300 Series Benutzerhandbuch

Viconics

Viconics VTR7300 Series Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Rockwell Automation

Rockwell Automation 1769-L31 Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Samson

Samson Type 5824 Service-Handbuch

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Fishman

Fishman TriplePlay Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung