Videosec CD-960H Bedienungsanleitung
Analog Camera User’s Manual
CD-960H
Important Safeguards and Warnings
1．Electrical safety
All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1.
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
2．Transportation security
Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.
3．Installation
Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.
If this product is installed in the ceiling, please make sure the installation position can sustain the min
50N.
4．Qualified engineers needed
All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.
5．Environment
This series analog camera should be installed in a cool, dry place away from direct sunlight or strong
light, inflammable, explosive substances and etc.
The working temperature ranges from -10℃to +60℃. Please keep it away from the electromagnetic
radiation object and environment.
Please make sure the CCD component is out of the radiation of the laser beam device. Otherwise it
may result in CCD optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
6. Accessories
Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.
7. Daily Maintenance
Please shut down the device and then unplug the power cable before you begin daily maintenance
work.
Do not touch the CCD optic component. You can use the blower to clean the dust on the lens surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD component when you do not use the camera.
3
1General Introduction
This series analog camera adopts the high sensitivity CCD and advanced circuit design. It is
featuring the high quality video, the lowest distortion, low noise and etc. This series product is
suitable to be used in surveillance system and video process system.
1.1 Features
zHigh-performance SONY CCD, high resolution, 700 TVL, vivid and impressive video
zSupport ICR (IR Cut Removal) auto switch, auto day/nigh mode switch or external activation
to realize the surveillance both in the daytime and at night. (Note: For F481EP, F581EP,
and F781EP series product only.)
zSupport WDR 500X, suitable for backlight environments.
zSupport ATW (auto trace white balance), ANTI CR (anti-color roll), MANUAL PUSH, PUSH
LOCK and etc. Restore high definition and more reliable video
zSupport privacy mask function. Set zone color, transparent, mosaic and etc.
zSupport motion detect function. Set zone sensitivity and block display.
zSupport video mirror, hue and color gain setup.
zSupport backlight compensation, high light compensation, close and etc according to the
actual environments.
zSupport ATR, ATR-EX functions.
zSupport 2D and 3D de-noise. High signal to noise ratio (SNR), clear and impressive video.
(Note: The F480EP, F480CP series product does not support 3D de-noise function.)
zSupport auto electronic gain control, self-adaptive brightness.
zSupport auto aperture function (DC or video drive)
zSupport flange-back adjustment, suitable for multiple models from various brands
zAuto exposure function
zSupport OSD (on-screen display), suitable for user self-defined setup.
zSupport RS485 remote control.
zSupport various languages such as English.
1.2 Functions
Motion detect
An alarm can be generated once there is moving object in the surveillance area. You can select
the various sensitivity levels according to your actual requirements.
Privacy mask
Support privacy mask area setup. Privacy masking area is a user-defined, four-sided area that
can not be viewed by you during the surveillance to protect the privacy information (such as the
keyboard zone of the ATM).
Day/night mode switch (Color and black/white switch)
This function allows the camera to display the color video in the day while the black and white
video at the night. It is to enhance camera sensitivity and definition.
4
Auto gain function
To output the standard video signal in the different illumination environments, the amplifier needs
to adjust in a wide range. The system can enhance the camera sensitivity in low illumination and
enhance the video signal output to get the clear and high definition video.
SNR
It is the ratio value between the signal voltage and the noise voltage. The higher the SNR value,
the lower the adverse effect. It is to guarantee the clear video.
OSD
User-friendly on-screen display for you to select the different functions.
INT and LL
There are two synchronization modes: INT/LL. INT is to use the oscillator of the camera to
generate the synchronization signal to complete the scan and synchronization. The LL is to
provide the AC current to the camera to realize the scan and synchronization.
White Balance
The white balance refers to the camera to restore the white object color. It allows the camera to
adjust the color temperature in indoor and outdoor environment, just like our human eyes does.
ICR
The IR cut removal is to filter the IR light in the daytime and then auto switch to the general fitter
at night. This function allows the camera to output the high sensitivity and clear video.
Auto exposure
System can automatically set shutter speed and iris value according to the snapshot video
exposure condition.
Low illumination
The system can output the proper video even in dark environment.
5
BLC
Once there is strong light at the back of the object, the main object video may become dark.
Backlight compensation technology is to automatically compensate the light to get vivid video.
You can refer to the following two figures to see the result of the backlight compensation
technology function.
Before After
WDR
When there is strong light, shadow and backlight all in one surveillance environment, the camera
output video may become white owning to the extra exposure while some sections become black
owning to the insufficient exposure. All of these will adversely affect the video quality. WDR is to
balance the light between these two sections.
You can compare the follow figure with the above figure on the left.
ATR and ATR-EX
ATR (Adaptive Tone-curve Reproduction) function allows the camera to digitally calculate the
video color again and then adjust the brightness to enhance the video quality. This function can
effectively enhance the color and black zone of the video when there is sharp light contrast in the
environments.
6
HLC
HLC (High Light Compensation) function can effectively remove the risk of over exposure and
guarantee the proper monitor video when there are strong lights.
De-noise (Noise reduction)
There may be too much noise when you are monitor in the low illumination environments. You
can digitally calculate to reduce the noise to get the clear video.
Digital image stabilization
When the installation position is of much vibration, you can enable this function to guarantee
clear and stable video.
Digital zoom
This function can allow you to clearly monitor the remote object. The camera can zoom in the
remote object and then output.
1.3 Specifications
Please refer to the following sheet for specification.
CD-960H
Video Processor 1/3" SONY EX view HAD CCD
Video Format PAL/NTSC
PAL 976（H）×582（V）570K pixels
Effective Pixel
NTSC 976（H）×494（V）480K pixels
Resolution (PAL) 960x576TVL
Color：0.02Lux/F1.2
Min Illumination
Black and white：0.005Lux/F1.2
PAL Auto: 1/50s~1/100,000s
Manual:
1/50s,1/120s,1/250s,1/500,1/1000s,1/2000s,
1/4000s,1/10,000s
Electronic Shutter
NTSC Auto: 1/60s~1/100,000s
Manual:
1/60s,1/100s,1/250s,1/500,1/1000s,1/2000s,
1/4000s,1/10,000s
Iris Control Mode Auto/manual
Lens Connection Type C/CS mount
Day/Night Switch ICR auto switch
Synchronization Mode INT/LL
7
Video Output 1Vp-p Composite Output（75Ohm/BNC）
SNR Above 60dB
LENS Manual/Video/DC
SHUTTER/AGC Auto/Manual
BACKLIGHT
(BLC)
Off/BLC/HLC(High light compensation )
WHITE
BALANCE
ATW/ ANTI CR /manual/push lock/push/user 1/user 2
DAY/NIGHT
MODE
Auto/external trigger/black and white/color
PICTURE
ADJUST
Mirror/brightness/contrast/sharpness/hue/gain
ATR Off/luminance/contrast
MOTION
DETECT
Detect sensitivity/block display/area selection
PRIVACY
MASK
Area selection/color/transparent/mosaic
NR Level/Y level/C level
Camera ID Character/position
Menu
Language English/Japanese and etc
Communication Port RS485
Working Temperature -10ºC ~ +60ºC
Power AC24V±10% / DC12V±10%
Power Consumption 6W Max
Dimension (mm) 131.3（L）×64.6（W）×61.2（H）
Weight 500g
8
2Framework
2.1 Dimension
Please refer to the following figures for dimension information. See Figure 2-1 and Figure 2-2.
Figure 2-1
Figure 2-2
9
2.2 Side Panel
This series analog camera side panel structure is shown as below. See Figure 2-3.
1: Flange-back. 2. Auto aperture port 3.Pedestal to secure the bracket
Figure 2-3
1 Flange-back
Usually the flange-back has been set to the proper position before it is shipped out of the factory.
But sometimes, you may still need to adjust a little bit to let it be suitable for different lens. Please
follow the steps listed below:
zSecure the lens.
zLoosen the screw to unlock the flange-back
zTurn the lens until you see the clear video.
zFix the screw again.
2. Auto aperture port
The auto aperture port interface is shown as below. See Figure 2-4.
Figure 2-4
10
Please refer to the following sheet for detailed information.
The video driver auto aperture uses the three pins: Power, Video and GND. The DC driver auto
aperture uses the four pins: Damp+, Damp-, driver +, Driver -.
Video DC
1 Power Damp-
2 NC Damp+
3 Video Driver+
4 GND Driver-
3. The pedestal to secure the bracket
It is to install the bracket.
Important
Please contact our local retailer if you want to use the video drive lens.
2.3 Rear Panel
2.3.1 CD-960H
This series product rear panel is shown as in Figure 2-5.
Figure 2-5
Inhaltsverzeichnis
Andere Videosec Sicherheitskamera Handbücher
