Videx 940ST Bedienungsanleitung

CONTENTS

PAGE 2 - BLOCK DIAGRAM

PAGE 3-5 - INTRODUCTION & DESCRIPTION

PAGE 6 - SENTRY 1 PCB DIAGRAM

PAGE 7- SENTRY 1 PCB CONNECTIONS

PAGE 8 - ISOLATION PCB DIAGRAM

PAGE 9 - ISOLATION PCB DESCRIPTION

PAGE 10 - INSTALLATION & TESTING

PAGE 11 - TELEPHONE CHART

PAGE 12 - ACCESSORIES DIAGRAM

PAGE 13 - WIRING DIAGRAM (VR PANEL)

PAGE 14 - WIRING DIAGRAM (ISOLATION)

PAGE 15 - WIRING DIAGRAM (3 DOOR)

PAGE 16 - WIRING DIAGRAM (VIDEO)

PAGE 17 - TROUBLE SHOOTING GUIDE

PAGE 18 - VR PANEL LAYOUTS

PAGE 19 - USER INSTRUCTIONS (925MSL)

PAGE 20 - USER INSTRUCTIONS (940ST)

SENTRY 1 CONTROL UNIT

Introduction

The information in this manual is intended as an installation and

commissioning guide for the sentry 1 system. This manual should be read

carefully before the installation commences. Any damage caused to the

equipment due to faulty installations where the information in this manual has

not been followed is not the responsibility of VIDEX security UK LTD.

Description

The sentry 1 system can be used as a one or two door audio or video system.

The system comprises of the functional door panels (with the required

number of buttons), a control cabinet, a lock release for each door and the

required number of handsets. The following optional extras can also be used

with the sentry 1 system :-

Fireman's switch•

Busy light•

Codelock•

Sentrykey•

Push to exit•

Door monitoring•

Extension speaker•

Extension strobe•

Battery discharge cut off PCB•

Isolation PCB•

Video•

VproX proximity system•

The sentry 1 system is a two door functional door entry system which can be

expanded to control more doors with the use of additional sentry 1 control

PCB’s (One required for every two doors).

The Door panel can consist of any number of buttons. The vandal resistant or

Brass door panels can be used with this system. The door panel will also

include a diode board which is used to indicate to the control PCB which door

the call has come from. The door panel can also be extended to include

optional extras (i.e. codelock, sentrykey, video etc).

The 431/B control consists of a 24 hour analogue time clock, a 1 amp PSU

and the sentry 1 control PCB all within a lockable cabinet. (There is also

room within the cabinet for a back up battery (max - 12V 7AH).

The 531/B control cabinet contains the same items as the 431/B, but is IP55

rated.

There is a large range of compatible audio Handsets the system will work

with, these are listed in this manual.

Videophones are available with door open button and spare services button.

Other options may be available on request.

The heart of the system is the sentry 1 control PCB, which has the following

features :-

12V DC operation3

Voltage free contacts for the lock outputs. (Double pole 5A 30VDC)3

Timed calltone, speak time and lock open time :-3

CALLTONE LENGTH

SW1 SW2 TIME

ON OFF 1 SECONDS

OFF ON 2 SECONDS

OFF OFF 4 SECONDS

ON ON 8 SECONDS

SPEECH LENGTH

SW3 SW4 TIME

ON OFF 16 SECONDS

OFF ON 32 SECONDS

OFF OFF 60 SECONDS

ON ON 120 SECONDS

LOCK OPEN TIME

SW5 SW6 TIME

ON OFF 2 SECONDS

OFF ON 8 SECONDS

OFF OFF 16 SECONDS

ON ON 40 SECONDS

Timeclock input3

Trade button input3

Busy light output3

Engaged output (for use with multiple door systems)3

Additionally, if video is required on the system an ART893/20 power supply

will be required. This power supply will supply a 20V DC output to both the

videophones and the camera and will be fitted within the control cabinet.

Operation :-

A call will be activated by a visitor pressing the desired flat number on the

door panel. A timed call tone will be heard at the occupants telephone. The

videophone will also switch on at this point for the flats with the video facility).

A reassurance call tone will also be heard at the door panel to indicate the

system has been activated. If the occupant does not answer the telephone,

the call will clear down. If the occupant does answer the telephone, the call

tone will stop as soon as the handset is lifted. A two way conversation can

now take place (This will time out after the preset time). If the occupant does

not want to let the caller into the building, the handset would be put back on

its cradle. If the occupier does want to let the caller into the building, the lock

button would be pressed and the door would open for the preset time. The

lock button will not work at any other time.

The trade buttons only works when the time clock is active. At this time when

a trade button is pressed the door will open for the preset time.

A busy light would be used when more than one door panel is connected to

the system. The busy light will illuminate when a call is activated at any door

panel.

The Sentry 1 PCB incorporates four LED's which are used to indicate what

state the PCB is in. These LED's are labeled D10, D11, D12, D13. They

relate to the following functions :-

D10 : When this is illuminated, the system is awaiting a call.

D11 : When this is illuminated, the system is busy.

D12 : When this is illuminated, the call is from door one.

D13 : When this is illuminated, the call is from door two.

The Sentry 1 PCB includes a link option (JPR1) which when in position A, the

system will only allow one call to be activated at anyone time. The system

must time out before another call can be registered. When the link is in

position B the system will allow another button to be pressed with out waiting

for the system to time out. (The link should only be fitted in position B when

the system is being tested or being used as a one door system).

VIDEX run training courses for engineers who have not installed the sentry 1

system before.

Technical help is also available on 0191 224 3174 during office hours (8:30 -

12:30 and 1:30 - 5:00).

Technical specification :-

Working voltage : 12V DC

Current (Quiescent) : 24mA

Current (During a call) : 195mA

Current (During door open) : 165mA (Not including lock)

Connections :-

JP1 - VIN + 12 VOLTS SUPPLY

- VOUT + 12 VOLTS OUT

- GND NEGATIVE SUPPLY

JP2 - CB BUTTON COMMONS

- 1 RECEIVE SPEECH (DOOR ONE)

- 2 TRANSMIT SPEECH (DOOR ONE)

- 3 SWITCHED + 12 VOLTS, AMP SUPPLY

- 4 NEGATIVE AMP SUPPLY

- A TRIGGER FROM DOOR ONE

JP3 - ENG ENGAGED OUTPUT (HIGH WHEN ENGAGED)

- 1 RECEIVE SPEECH (DOOR TWO)

- 2 TRANSMIT SPEECH (DOOR TWO)

- 3 SWITCHED + 12 VOLTS, AMP SUPPLY

- 4 NEGATIVE AMP SUPPLY

- A TRIGGER FROM DOOR TWO

JP4 - 1 TRANSMIT SPEECH PHONE CONNECTION

- 2 RECEIVE SPEECH PHONE CONNECTION

- 4(T) CALLTONE TO PHONES

- 5(P) LOCK TRIGGER FROM PHONES

- 7(-) NEGATIVE TO PHONES

- +12V 12 VOLTS SUPPLY TO PHONES

JP5 - TC1 TRADE BUTTON FOR DOOR ONE

- TC1 TRADE BUTTON FOR DOOR ONE

- TC2 TRADE BUTTON FOR DOOR TWO

- TC3 TIME CLOCK CONNECTION

JP6 - NO1 NORMALLY OPEN 1 (LOCK, DOOR 1)

- CO1 COMMON 1 (LOCK, DOOR 1)

- NC1 NORMALLY CLOSED 1 (LOCK, DOOR 1)

- NO2 NORMALLY OPEN 2 (LOCK, DOOR 1)

- CO2 COMMON 2 (LOCK, DOOR 1)

- NC2 NORMALLY CLOSED 2 (LOCK,DOOR 1)

JP7 - NO1 NORMALLY OPEN 1 (LOCK, DOOR 2)

- CO1 COMMON 1 (LOCK, DOOR 2)

- NC1 NORMALLY CLOSED 1 (LOCK, DOOR 2)

- NO2 NORMALLY OPEN 2 (LOCK, DOOR 2)

- CO2 COMMON 2 (LOCK, DOOR 2)

- NC2 NORMALLY CLOSED 2 (LOCK,DOOR 2)

4 WAY ISOLATION PCB

Description :-

One PCB required for every four handsets.•

Isolates the speech, lock and call lines with the use of relays.•

protects the +12v supply and door monitoring line with fuses.•

There are LED's on the isolation PCB to indicate which phone has been•

enabled.

All connections are via plugs.•

Operation :-

The selects from the call buttons all go to a separate outputs on JP6 (either

A,B,C or D). When one of these outputs goes high (i.e. with a call to that

output), a thyristor on the isolation PCB is triggered, which in turn energises

the relays for that handset. Each of the four outputs on the isolation PCB

have two relays which reconnects the connections on JP1 with the

connections on that phone output (either JP2, JP3, JP4 or JP5). The thyristor

is held on by the voltage on the SW+ terminal on JP1. This voltage is only

there when a call is in progress.

Technical specification

Number of users : 4

Input voltage : 12VDC

Current (Quiescent) : 0mA

Current (During call) : 47.6mA

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Videx Gegensprechanlage Handbücher

Videx

Videx DIGITAL GSM DOOR INTERCOM SYSTEM Bedienungsanleitung

Videx

Videx VK8K Systemhandbuch

Videx

Videx VRVK Series Systemhandbuch

Videx

Videx VK4K/5456 Series Systemhandbuch

Videx

Videx VK8K/6256 Series Systemhandbuch

Videx

Videx VX2200 Bedienungsanleitung

Videx

Videx 4000 Series Bedienungsanleitung

Videx

Videx 4000 Series Bedienungsanleitung

Videx

Videx 4000 Series Bedienungsanleitung

Videx

Videx 4000 Series Bedienungsanleitung

Videx

Videx 3000 Series Bedienungsanleitung

Videx

Videx VIDEOKIT ESVK/6286 Series Systemhandbuch

Videx

Videx IP videokit IPVK/6296 Series Systemhandbuch

Videx

Videx IP videokit IPVK/6296 Series Systemhandbuch

Videx

Videx 5178 Bedienungsanleitung

Videx

Videx 5178N Bedienungsanleitung

Videx

Videx VRDK1 (25H) Bedienungsanleitung

Videx

Videx 6200 Series Bedienungsanleitung

Videx

Videx VX2300 Bedienungsanleitung

Videx

Videx 4000 Series Bedienungsanleitung

Videx

Videx 5418 Bedienungsanleitung

Videx

Videx 4000 Series Bedienungsanleitung

Videx

Videx Door Intercom System Bedienungsanleitung

Videx

Videx KRV98 Gebrauchsanweisung

Beliebte Gegensprechanlage Handbücher anderer Marken

Bticino

Bticino LINEA 3000 Bedienungsanleitung

MSI

MSI MSI-140 Bedienungsanleitung

golmar

golmar Stadio Plus Bedienungsanleitung

CyberData

CyberData 011211 series Handbuch

Vidos

Vidos duo M1021 Bedienungsanleitung

Vimar

Vimar ELVOX 7539/E Bedienungsanleitung

SSS Siedle

SSS Siedle BTSV 850-03 Bedienungsanleitung

Dahua

Dahua VTO Series Bedienungsanleitung

Elvox

Elvox 5651 Bedienungsanleitung

Rocom

Rocom Doortello Business FW T2.05W2.04 Bedienungsanleitung

Viking

Viking E-35-EWP Bedienungsanleitung

Safeguard Supply

Safeguard Supply LRA-EX1000 Bedienungsanleitung

SSS Siedle

SSS Siedle BFCV 850 Series Bedienungsanleitung

GRD

GRD MAX V2 Bedienungsanleitung

Alecto

Alecto ADI-250 Bedienungsanleitung

Aiphone

Aiphone IE-8MD Bedienungsanleitung

Perel

Perel EDB4 Bedienungsanleitung

Bticino

Bticino Classe 300 Bedienungsanleitung