Videx 3676 Bedienungsanleitung

66251010-EN - V2.1 - 31/05/16

3600 Series

Art.3676 - Installation instructions

161

178

218

Fig. 1

678

1235

SW1

1234

SW2

123

SW3

Fig. 2

DESCRIPTION

Intelligent videophone for the VX2200 digital system incorporating a 3,5”full colour active matrix LCD monitor, with“camera recall”,

“door open”, “privacy/service” buttons plus 3 LEDs related to the operation of the buttons. Programmable settings: video mode

(coax or balanced), melody, number of rings and privacy duration.

Adjustments: call tone volume (3 levels), hue and brightness. Connection terminals are compatible with Art.3678.

PUSH BUTTONS AND CONTROLS  OPERATION

Camera recall button.

When the system is in standby, (No calls on the system) operation of this button will open the speech to the door station.

The related LED will illuminate. Press as many time as the ID value of the door panel to connect to.

Door-open button.

• During a conversation, operation of this button will release the door from where the call originated. This will be con-

rmed by an acoustic tone. If terminal“DL”is connected, the“door open”LED next to the button will also be illuminated.

• When the system is in stand-by, a button press will book a call to the concierge (If available).

Privacy ON-OFF button.

• When the system is in stand-by, press this button to enable the service for the programmed time: the related LED

will illuminate to signal the service enabled. During an incoming call, with the service enabled, the device does not

emit any acoustic signal. The service is disabled when the programmed time expires or pressing again the button.

• During a conversation, press this button to enable the auxiliary service: by pressing the button terminal“12/SB” is

internally linked to ground for 2 seconds.

Adjusts call tone volume (3 levels): low, medium and high.

Adjusts the picture hue: right rotation to increase, left rotation to decrease.

Adjusts the picture brightness: right rotation to increase, left rotation to decrease.

Art.3676 Digital videophone for VX2200 Digital System

66251010-EN - V2.1 - 31/05/16

3600 Series

Art.3676 - Installation instructions

PROGRAMMING AND ADJUSTMENTS

The programmable settings are:

• Melody (9 available);

• Number of rings (3 or 6);

• Video mode (coax or balanced);

• Privacy duration (15minutes – 16 hours or unlimited);

• Videophone address (Phone ID).

TO SET MELODY

Press and hold (for approx 10 seconds) the “ ” button un-

til the unit plays the current programmed melody and emits a

beep at the end. Press again the “ ” button to listen to the

available melodies (maximum 9). Once the selected melody has

been reached, wait 5 seconds for a beep. The new melody will

be stored.

TO SET THE NUMBER OF RINGS 6 OR 3

Default setting is 6, to set 3 proceed as follows:

a. Turn o the videophone by unplugging the at cable from

the PCB connection board;

b. Make a short between terminals 8 and 9 (signals “GND” and

“LB”) of the PCB connection;

c. Plug the at cable onto the PCB connection board and wait for

a beep before removing the short between terminals 8 and 9;

d. To go back to 6 rings, do the same but two beeps will be emitted.

TO SET THE VIDEO MODE

The videophone can operate with ei-

ther composite video signal (coax cable)

or balanced video signal (two wires).

Switches 1 & 2 of SW2 are used to set vid-

eo mode while switches 3 & 4 are for vid-

eo termination. When more videophone

have a pass through connection for the

video signal, you must enable the video

termination only for the last videophone.

VIDEO MODE  SW2

Switches 1,2 Mode

Coax

Balanced

75 OHM VIDEO TERMINATION  SW2

Switches 3,4 Termination

Enabled

Disabled

TO SET THE PRIVACY DURATION

The privacy duration is set by the 3 way dip-switch bank SW3. PRIVACY DURATION  SW3

SW3 Dip-Switch Duration

123

o o o Unlimited

on o o 15 min

o on o 30 min

on on o 1 hour

o o on 2 hours

on o on 4 hours

o on on 8 hours

on on on 16 hours

Art.3676 Digital videophone for VX2200 Digital System

66251010-EN - V2.1 - 31/05/16

3600 Series

Art.3676 - Installation instructions

VIDEOMONITOR/INTERCOM ADDRESS, VIDEO MODE AND TERMINATION SETUP

Each intercom is addressed in binary (PHONE ID) using the 8 way dipswitches located on the rear of the unit. Each switch corre-

sponds to one bit which can have a value 0 (OFF) or 1 (ON). Each bit corresponds to a decimal weight depending on the position:

Switch 1 = decimal 1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. I.E. to set the address 37, put switches 1, 3 and 6 on (1+4+32=37).

SWITCHES DECIMAL WEIGHT ADDRESS

8 7 6 5 4 3 2 1 128 64 32 16 8 4 2 1

OFF OFF OFF OFF OFF OFF OFF ON 0 0 0 0 0 0 0 1 1

OFF OFF OFF OFF OFF OFF ON OFF 0 0 0 0 0 0 1 0 2

OFF OFF OFF OFF OFF OFF ON ON 0 0 0 0 0 0 1 1 3

OFF OFF OFF OFF OFF ON OFF OFF 0 0 0 0 0 1 0 0 4

OFF OFF ON OFF OFF ON OFF ON 0 0 1 0 0 1 0 1 37

ON OFF ON ON OFF ON OFF OFF 1 0 1 1 0 1 0 0 180

SIGNALS ON CONNECTION BOARD

+20V 1 Video power supply 17÷20Vdc

+20V 2 Video power supply 17÷20Vdc

GND 3 Video power supply ground reference

GND 4 Video power supply ground reference

V2/V 5 Balanced video signal V2 sync.(balanced video signal mode)

Composite video signal (coax video signal mode)

V1 6 Balanced video signal V1 sync.(balanced video signal mode)

L 7 BUS line

GND 8 BUS line ground reference

LB 9 Local bell input (active low)

AL 10 Alarm input (active low)

SB 12 Service Push button (close to ground when pressed)

EXTC 13 Call tone output for extension sounder like Art.512A

+VD 15 +12Vdc output to supply the video distributor Art.894/Art.894N

GND 16 Ground

LDO 19 Auxiliary LED ( button) power supply input

GND 20 Ground

TECHNICAL SPECIFICATION

Working Voltage: 17÷20Vdc

Power Consumption: Standby: 12mA

During a conversation: 250mA Max (on 20Vdc)

Working Temperature: -10°C +50°C

Art.3676 Digital videophone for VX2200 Digital System

66251010-EN - V2.1 - 31/05/16

3600 Series

Art.3676 - Installation instructions

Art.3676 Digital videophone for VX2200 Digital System

66251010-EN - V2.1 - 31/05/16

3600 Series

Art.3676 - Installation instructions

Art.3676 Digital videophone for VX2200 Digital System

66251010-EN - V2.1 - 31/05/16

3600 Series

Art.3676 - Installation instructions

Fig. 2

3600 Series Videophone wall mounting instructions

135cm

Fig. 1

Fig. 3

Fig. 4

Fig. 5

1. Cables must be fed through the opening E(Fig. 2) of the mounting plate C, which should be tted approximately 135cm from

nished oor level as shown in Fig. 1;

2. Place the mounting plate Cagainst the wall feeding the wire group Dthrough opening Eof the mounting plate and mark the

xing holes A(Fig. 2);

3. Drill the xing holes A, insert the wall plugs Bthen with the cables threaded through opening Ex the mounting plate Cto the

wall with the 4 screws provided F(Fig. 2);

4. Hook the PBC connection board Gto the mounting plate Cas shown in Fig. 3 and connect the wires (using the screwdriver

provided) to the terminals as shown in the diagram provided;

5. Once the wires are connected, hook the videophone Hto the mounting plate Cas shown in Fig. 3;

6. Connect the Plug Ion the ribbon cable from the videophone to the plug Lon the PCB connection board G;

7. Place the videophone Hagainst the 4 hooks Mon the mounting plate C(in line with the 4 openings Non the rear side of the

videophone Fig. 5) and push down as suggested by the pointers in Fig. 4, the videophone will lock into place;

8. To remove the videophone, hold it rmly and push the unit in an upward direction until the videophone Hunlocks from the

mounting plate C.

66251010-EN - V2.1 - 31/05/16

3600 Series

Art.3676 - Installation instructions

Note

MANUFACTURER

VIDEX ELECTRONICS S.P.A.

Via del Lavoro, 1 - 63846 Monte Giberto (FM) Italy

Tel (+39) 0734 631669 - Fax (+39) 0734 632475

www.videx.it - inf[email protected]

CUSTOMER SUPPORT

All Countries:

VIDEX ELECTRONICS S.P.A.

www.videx.it - technical@videx.it

Tel: +39 0734-631669 - Fax: +39 0734-632475

UK Customers:

VIDEX SECURITY LTD

www.videx-security.com

Tech Line: 0191 224 3174 - Fax: 0191 224 1559

The product is CE marked demonstrating its conformity and is for distribution

within all member states of the EU with no restrictions. This product follows

the provisions of the European Directives 2014/30/EU (EMC); 2014/35/EU

(LVD); 2011/65/EU (RoHS): CE marking 93/68/EEC.

Main UK oce:

VIDEX SECURITY LTD

1 Osprey Trinity Park

Trinity Way

LONDON E4 8TD

Phone: (+44) 0870 300 1240

Fax: (+44) 020 8523 5825

www.videx-security.com

marketing@videx-security.com

Northern UK oce:

VIDEX SECURITY LTD

Unit 4-7

Chillingham Industrial Estate

Chapman Street

NEWCASTLE UPON TYNE - NE6 2XX

Tech Line: (+44) 0191 224 3174

Phone: (+44) 0870 300 1240

Fax: (+44) 0191 224 1559

Greece oce:

VIDEX HELLAS Electronics

48 Filolaou Str.

11633 ATHENS

Phone: (+30) 210 7521028

(+30) 210 7521998

Fax: (+30) 210 7560712

www.videx.gr

[email protected]

Danish oce:

VIDEX DANMARK

Hammershusgade 15

DK-2100 COPENHAGEN

Phone: (+45) 39 29 80 00

Fax: (+45) 39 27 77 75

www.videx.dk

[email protected]

Benelux oce:

VIDEX BENELUX

E3 Iaan, 93

B-9800 DEINZE

Phone: (+32) 9 380 40 20

Fax: (+32) 9 380 40 25

www.videxbenelux.be

[email protected]

Inhaltsverzeichnis

Andere Videx Telefon Handbücher

Videx

Videx 6400 SERIES Bedienungsanleitung

Videx

Videx 6778 VX2200 Bedienungsanleitung

Videx

Videx 3000 Series Bedienungsanleitung

Videx

Videx 3311 Bedienungsanleitung

Videx

Videx 6300 Series Bedienungsanleitung

Videx

Videx 3000 Series Bedienungsanleitung

Videx

Videx 3686 Bedienungsanleitung

Videx

Videx 6700 Series Bedienungsanleitung

Videx

Videx 3000 Series Bedienungsanleitung

Videx

Videx 3000 Series Bedienungsanleitung

Videx

Videx 280N1 Bedienungsanleitung

Videx

Videx 6231 Bedienungsanleitung

Videx

Videx 3000 Series Bedienungsanleitung

Videx

Videx 3000 Series Bedienungsanleitung

Videx

Videx 3000 Series Bedienungsanleitung

Videx

Videx 6400 SERIES Bedienungsanleitung

Videx

Videx 3000 Series Bedienungsanleitung

Videx

Videx 6276 Bedienungsanleitung

Videx

Videx 4KC Series Bedienungsanleitung

Videx

Videx 3000 Series Bedienungsanleitung

Videx

Videx 6388 Bedienungsanleitung

Videx

Videx 3676 Bedienungsanleitung

Videx

Videx 6700 Series Bedienungsanleitung

Videx

Videx Kristallo Series Bedienungsanleitung

Beliebte Telefon Handbücher anderer Marken

GE 2-9480 Bedienungsanleitung

Geemarc

Geemarc PHOTOPHONE 155 Bedienungsanleitung

D-Link

D-Link DWR-720/PW Bedienungsanleitung

Interquartz

Interquartz Gemini IQ333 Bedienungsanleitung

SSS Siedle

SSS Siedle HT 840-0 Bedienungsanleitung

Motorola

Motorola TITANIUM Bedienungsanleitung

Panasonic

Panasonic ICX Bedienungsanleitung

LG H870DS Bedienungsanleitung

Samsung

Samsung GT-I9500 Bedienungsanleitung

AT&T

AT&T Trimline 205 Bedienungsanleitung

Selta

Selta zenyth 600 Bedienungsanleitung

Doro

Doro AFTI 20 Bedienungsanleitung

UNIQCELL

UNIQCELL A1 Bedienungsanleitung

Panasonic

Panasonic KX Series Bedienungsanleitung

Jabra

Jabra SP5050 - Bluetooth hands-free Speakerphone Bedienungsanleitung

BT Decor 425 Bedienungsanleitung

NEC

NEC SV8500 Bedienungsanleitung

Teledex

Teledex PEARL Bedienungsanleitung