Viega Pressgun 5 Bedienungsanleitung
Instructions for Use
Press machinePressgun 5
Model
0798.5
AU
Table of contents
1About these instructions for use 3
1.1 Target groups 3
1.2 Labelling of notes 3
1.3 About this translated version 4
1.4 Note on use of abbreviated terms 4
2Product information 5
2.1 Standards and regulations 5
2.2 General safety advice for electrical tools 5
2.3 Intended use 9
2.3.1 Areas of application 9
2.4 Product description 9
2.4.1 Overview 9
2.4.2 Technical data 10
2.4.3 Operating mode 12
2.4.4 Control elements and indicators at the press
machine 12
3Handling 14
3.1 Transport and storage 14
3.2 Commissioning 15
3.3 Carrying out the pressing process 16
3.4 Aborting the pressing process 17
3.5 Troubleshooting 17
3.6 Care and maintenance 18
3.6.1 Cleaning the press tools 18
3.6.2 Performing checks 19
3.6.3 Inspection and maintenance 19
3.7 Disposal 20
4Appendix 21
4.1 Warranty 21
4.2 Service partners 21
Table of contents
Press machinePressgun 5 2
1 About these instructions for use
Trade mark rights exist for this document; for further information, go to
viega.com/legal.
These instructions are a translation of the original operating instructions.
1.1 Target groups
The information in these operating instructions is directed at the fol‐
lowing groups of people:
nHeating and plumbing experts and trained personnel
This product must not be used by persons who do not have the afore‐
mentioned training or qualifications.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
About these instructions for use
Press machinePressgun 5 3
1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e.g. EN) and/or in Germany
(e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand‐
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
1.4 Note on use of abbreviated terms
For reading comfort, the following abbreviated terms are used in these
instructions for use:
Term Abbreviated form
Viega system press jaws Press jaws
Viega system press rings Press rings
Viega system press tool Press tool
Combinations of for example:
nPress machine and press jaws
nPress machine and
Press Booster
nPress machine with hinged
adapter jaws and press ring or
press chain
nPress machine and press-in
attachment tool
About these instructions for use
Press machinePressgun 5 4
2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe.
National regulations can be found on the relevant web site of your
country at viega.com.au/standards
Regulations from section: Technical data
Scope / Notice Regulations applicable in Ger‐
many
Oscillation emission value
Protection classes
EN 60745-1
2.2 General safety advice for electrical tools
This section contains general safety instructions for numerous different
products and electrical tools. Consequently, not every safety instruction
will apply to this tool.
WARNING!
Read all safety warnings, instructions, illus‐
trations and specifications provided with this
power tool.
Failure to follow all instructions listed below may result in
electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated
(corded) power tool or battery-operated (cordless) power tool.
a) Keep work area clean and well lit.
Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust.
Power tools create sparks which may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
Work area safety
Product information
Press machinePressgun 5 5
a) Power tool plugs must match the outlet. Never modify the plug in any
way. Do not use any adapter plugs with earthed (grounded) power tools.
Unmodified plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators.
There is an increased risk of electric shock if your body is earthed or
grounded.
c) Do not expose power tools to rain or wet conditions.
Water entering a power tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp edges
or moving parts.
Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suit‐
able for outdoor use.
Use of a cord suitable for outdoor use reduces the risk of electric shock.
f) lf operating a power tool in a damp location is unavoidable, use a
residual current device (RCD) protected supply.
Use of an RCD reduces the risk of electric shock.
a) Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired or
under the influence of drugs, alcohol or medication.
A moment of inattention while operating power tools may result in
serious personal injury.
b) Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes, hard
hat or hearing protection used for appropriate conditions will reduce
personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position
before connecting to power source and/or battery pack, picking up or
carrying the tool.
Carrying power tools with your finger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool
on.
A wrench or a key left attached to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper footing and balance at all times.
This enables better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair
and clothing away from moving parts.
Loose clothes, jewellery or long hair can be caught in moving parts.
g) lf devices are provided for the connection of dust extraction and col‐
lection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
Electrical safety
Personal safety
Product information
Press machinePressgun 5 6
h) Do not let familiarity gained from frequent use of tools allow you to
become complacent and ignore tool safety principles.
A careless action can cause severe injury within a fraction of a second.
a) Do not force the power tool. Use the correct power tool for your
application.
The correct power tool will do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
c) Disconnect the plug from the power source and/or remove the bat‐
tery pack, if detachable, from the power tool before making any adjust‐
ments, changing accessories, or storing power tools.
Such preventive safety measures reduce the risk of starting the power
tool accidentally.
d) Store idle power tools out of the reach of children and do not allow
persons unfamiliar with the power tool or these instructions to operate
the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for misalignment or
binding of moving parts, breakage of parts and any other condition that
may affect the power tool's operation. lf damaged, have the power tool
repaired before use.
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean.
Properly maintained cutting tools with sharp cutting edges are less likely
to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with
these instructions, taking into account the working conditions and the
work to be performed.
Use of the power tool for operations different from those intended could
result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and
grease.
Slippery handles and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
a) Recharge only with the charger specified by the manufacturer.
A charger that is suitable for one type battery pack may create a risk of
fire when used with another battery pack.
b) Use power tools only with specifically designated battery packs.
Use of any other battery packs may create a risk of injury and fire.
c) When battery pack is not in use, keep it away from other metal
objects, like paper clips, coins, keys, nails, screws or other small metal
objects, that can make a connection from one terminal to another.
Shorting the battery terminals together may cause burns or a fire.
Power tool use and care
Battery tool use and care
Product information
Press machinePressgun 5 7
d) Under abusive conditions, liquid may be ejected from the battery;
avoid contact. lf contact accidentally occurs, flush with water. lf liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritation or burns.
e) Do not use a battery pack or tool that is damaged or modified.
Damaged or modified batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
f) Do not expose a battery pack or tool to fire or excessive temperature.
Exposure to fire or temperature above 130 °C may cause explosion.
g) Follow all charging instructions and do not charge the battery pack or
tool outside the temperature range specified in the instructions.
Charging improperly or at temperatures outside the specified range may
damage the battery and increase the risk of fire.
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts.
This will ensure that the safety of the power tool is maintained.
b) Never service damaged battery packs.
Service of battery packs should only be performed by the manufacturer
or authorized service providers.
a) Use the correct tools.
Only use the tools and accessories listed in the operating instructions.
Do not use electric tools for purposes or work they are not intended for.
b) Secure the workpiece.
Use clamping devices or a vice to hold the workpiece. lt is held more
securely than it would be by hand and both your hands are free to
operate the tool.
c) Leave protective equipment in place.
d) Hand-held devices must not to be used as stationary equipment.
e) Do not hold the device in the compression area.
f) Do not hold any body parts or foreign objects between the press jaws
when activating the pressing cycle. Do not hold the jaw lever during the
pressing cycle. Danger of crushing!
There is a danger of crushing the Fingers and hands.
g) Observe the safety instructions for the cleaning and corrosion protec‐
tion agents used by you.
h) Ensure that the workpiece is not under tension.
Service
Basic safety rules
Product information
Press machinePressgun 5 8
2.3 Intended use
2.3.1 Areas of application
The Viega system press machine Pressgun 5 is intended for pressing
press connectors into the respective piping systems. In combination
with Viega system press jaws, the press tool is suitable for use with all
Viega plumbing and heating installation systems up to and including
dimension 108 as well as dimension ⅜ up to 2 inches.
2.4 Product description
2.4.1 Overview
Fig. 1: Overview of the machine elements
1 - LED light
2 - Cylinder head with press jaw fixture (180° rotatable)
3 - Retaining bolt
4 - Start button
5 - Bracket for battery or mains adapter
6 - Battery (depends on scope of delivery)
7 - Mains adapter (depends on scope of delivery)
8 - Button for manual release
Product information
Press machinePressgun 5 9
Refer to the model number to see the scope of delivery of your press
machine in the table below:
Model number 2293.2 2293.1 5393.2 5393.1 2295.2 2295.1 0798.5
Pressgun 5 X X X X X X X
Press jaw set PT2 (dimensions
15 / 22 / 28)
X X - - - - -
Press jaw set Raxofix (dimen‐
sions 16 / 20 / 25)
- - X X - - -
Lithium ion rechargeable bat‐
tery (18 V / 2.0 Ah)
X - X - X - X
Battery charger (230 V / 18 V) X - X - X - X
Mains adapter 230 V / 50 Hz - X - X - X -
Case X X X X X X X
Instructions for use X X X X X X X
2.4.2 Technical data
Nominal output 490 W
Voltage 18 V DC
Machine monitoring electronic
Sound pressure level 80 dB(A)
Uncertainty 3 dB(A)
Oscillation level < 2.5 m/s2
Uncertainty (K) 1.5 m/s2
Power transmission hydraulic
Thrust on piston 32 kN
Switch-on duration Maximum three pressings per
minute (≤ DN54)
Weight with rechargeable battery 3.8 kg
Protection class IP 44 *
* pursuant to the applicable directives, see
Ä
‘Regulations from sec‐
tion: Technical data’ on page 5
Scope of delivery
Press machine
Product information
Press machinePressgun 5 10
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Viega Werkzeuge Handbücher
Viega
Viega 2489.1 Bedienungsanleitung
Viega
Viega Pressgun Picco Bedienungsanleitung
Viega
Viega Smartpress Bedienungsanleitung
Viega
Viega 50000 Merkblatt
Viega
Viega PureFlow 50030 Merkblatt
Viega
Viega Megapress Bedienungsanleitung
Viega
Viega MegaPress Z3 Actuator Bedienungsanleitung
Viega
Viega PureFlow Merkblatt
Viega
Viega Pressgun Picco 6 Plus Bedienungsanleitung
Viega
Viega 6 PlusPress Bedienungsanleitung
